-
Davis Instruments 600E - page 1
Driv eRight OBDII Installation Guide ...
-
Davis Instruments 600E - page 2
FCC Part 15 Class B Registration Warning This equipment has been tested an d found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable prot ection against harmful inte rference in a residential instal- lation. This equipment generat es, uses, and can radiate ...
-
Davis Instruments 600E - page 3
1 Introduction This manual provides instructions an d information necessary to i nstall the OBD version o f the DriveRight 600 E device. The DriveRight OBD plugs into your vehicle’ s OBDII (On-Board Diagnostics II) port for a quick and easy installation. Note: DriveRight OBD only functions in vehicles equipped with a compatible OBDII port. See ? ...
-
Davis Instruments 600E - page 4
2 Cables Wiring Components Additional DriveRight Document ation Refer to the following documents fo r informati on on configuring and using your DriveRigh t: • The DriveRight 600 E User ’ s Guide included with your un it. • The Online Hel p System in the DriveRigh t software. • The DriveRight FMS User ’ s Manual located in an Adobe Acroba ...
-
Davis Instruments 600E - page 5
3 Installations using Adapter Cable Digital Inputs If you are using t he adapter cable digital inputs in your installatio n, the following additional tools and ot her it ems may also be required: • Crimping T ool • Multimeter • Fuse T ap - Required to obtain +12 V from the fuse panel. Planning the Inst allation Installation of theDriveRight O ...
-
Davis Instruments 600E - page 6
4 Wiring Diagra m The diagram below is an exampl e of DriveRight OBD wiring. Procedure 1: Connect OBD Cable to OBDII Port. 1. Locate the OBDII port in the vehicle. The OBDII port will be located within 3 feet of the steering wheel, usually within the general area indicated by the dotted li ne in the illustration below . The port should be easily ac ...
-
Davis Instruments 600E - page 7
5 Look in the follow areas if you have trouble finding the OBDII port: • Under the dash • In front of the passenger seat • Behind the ash tray • Behind a small access panel in the dash • In or around the center console 2. Plug the OBD cab le into the port. Note: The indicator light blinks three times when first plugged in, then blinks tw ...
-
Davis Instruments 600E - page 8
6 1. If you are installing a DriveRight 600 E OBD but not using the digital inputs, go to Step 10 of this procedure. 2. Butt splice the red fuse holder to the red wire from the adapter cable. 3. T ap the red fuse holder to an unswitched +12 V source using the in- line splice provid ed with your Driv eRight or using a fuse tap con- nector (not inclu ...
-
Davis Instruments 600E - page 9
7 7. Use the in-line butt splices to connect th e blue wires with fuses to the Green (Digital Input 1) and Y ellow (Digital Input 2) wires from th e adapter cable. 8. Connect Digital Input 1 to the desired circuit. 9. Connect Digital Input 2 to the desired circuit. 10.Connect the digital input cable to the OBD cable. It is easiest to make the conne ...
-
Davis Instruments 600E - page 10
8 T op of Dashboard Mountin g Using Brackets or V elcro™ Sun Visor Mounting 2. Insert the battery into the DriveRigh t console. Pan Head Self-T apping Screw Split-Lock Washer Flat Washer Hex Nut Split-Lock Washe r Flat Washer Right Angle Adapter Bracket Mounting Bracket Flat Head Machine Screw Bracket Mounting Loops Hooks V elcro Mounting 3 Bumps ...
-
Davis Instruments 600E - page 11
9 3. Connect the DriveRight console cable to the adapter cable. Note: T o disconnect the cables, hold the bot h cables by the c onnector housing and pull apart. The sliding housing on the console cable connecto r will release the lock and allow the cables to be separated. Once plugged in, the console should “wake-up” into the Current Readings s ...
-
Davis Instruments 600E - page 12
10 Appendix 1: OBDII Comp atibility Use this list to verify the compatibility of your vehi cle’ s OBDII port with DriveRight OBD. Supported OBDII Protocols • J1850-41.6 (PW M) • J1850-10.4 (VPW) • ISO9141 • KWP2000 (ISO 14230) • CAN (Controller Area Network - ISO1 1898) Supported US V ehicles • Most domestic and i mport vehicles, 1996 ...
-
Davis Instruments 600E - page 13
11 T echnical Support If you are experiencing prob lems with your Dri veRight, first check the cable connections and veri fy the calibration sett ings. If you are unable to solve the problem, please call Da vis T echnical Support. W e’ll be glad to help. Most questions can be answered on the phone. Y ou can also email us for support, o r visit ou ...
-
Davis Instruments 600E - page 14
12 Inst allation Notes: ...
-
Davis Instruments 600E - page 15
13 Inst allation Notes: ...
-
Davis Instruments 600E - page 16
14 Inst allation Notes: ...
Davis Instruments 600Eについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもDavis Instruments 600Eの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDavis Instruments 600Eで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。