Echo HCA-260の取扱説明書

35ページ 0.82 mb
ダウンロード

ページに移動 of 35

Summary
  • Echo HCA-260 - page 1

    Shaft Hedge Clipper Operator's Manual MODEL: HCA-261 Serial Number 002001001 - 02999999 W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe opera- tion. Failure to do so could result in serous injury. X7500012 ...

  • Echo HCA-260 - page 2

    1 SUP22203863 SUPPLEMENT TO OPERA TOR'S MANUAL Model HCA-260, HCA-261 Serial Number: All SUPLEMENTO DEL MANUAL DEL OPERADOR Modelo HCA-260, HCA-261 Número de serie: T odas This Supplement contains important information. Please keep with your Operator’s Manual. The following section has been added: 99922203863 08/05 ROT A TE CUTTER ASSEMBL Y ...

  • Echo HCA-260 - page 3

    SUPPLÉMENT AU MANUEL DE L’OPÉRATEUR Modèle: HCA-260, HCA-261 Numéro de série: Tous 2 Ce supplément contient l’information importante. V euillez le garder avec le manuel de votre opérateur . La section suivante a été ajouté: ADVERTENCIA PELIGRO Las hojas del cortasetos están muy afiladas. Lleve guantes para protegerse las manos al gir ...

  • Echo HCA-260 - page 4

    ...

  • Echo HCA-260 - page 5

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 3 M ANUAL S AFETY S YMBOLS AND I MPORT ANT I NFORMA TION Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. This s ...

  • Echo HCA-260 - page 6

    4 Shaft Decal Spanish Decal Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Read and understand Operator's ...

  • Echo HCA-260 - page 7

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 5 • Check that shoulder harness is adjusted for safe, comfortable operation. • Tighten the blade angle adjustment lever before operating. Spark Arrestor - Catalytic Muffler / Muffler • The muffler or catalytic muffler controls the exhaust noise and emissions. The spark arrestor screen prevent ...

  • Echo HCA-260 - page 8

    6 After Refueling; • Wipe any spilled fuel from the unit. • Move at least 3 M (10 ft.) from refueling location before starting. After Use; • DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. PERSONAL CONDITION AND SAFETY EQUIPMENT Physical Condition Your judgment and physical ...

  • Echo HCA-260 - page 9

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 7 Proper Clothing Wear snug fitting, durable clothing; • Pants should have long legs, shirts with long sleeves. • DO NOT WEAR SHORTS, • DO NOT WEAR TIES, SCARVES, JEWELRY. Wear sturdy work shoes with non-skid soles; • DO NOT WEAR OPEN TOED SHOES, • DO NOT OPERATE UNIT BAREFOOTED. Hot Humi ...

  • Echo HCA-260 - page 10

    8 Avoid Hot Surfaces • During operation, the muffler or catalytic muffler and surrounding cover may become extremely hot. Avoid contact during and immedi- ately after operation. Always keep exhaust area clear of flammable debris. Allow the engine and muffler to completely cool before performing any maintenance activity. Keep A Firm Grip • Hold ...

  • Echo HCA-260 - page 11

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 9 EXTENDED OPERA TION / EXTREME CONDITIONS Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensati ...

  • Echo HCA-260 - page 12

    10 D ESCRIPTION The ECHO product you have purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly of Model HCA-261 is required. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. ...

  • Echo HCA-260 - page 13

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 11 1 2 3 4 5 6 7 8 12 14 15 16 17 18 19 20 21 22 23 24 9 11 13 10 25 ...

  • Echo HCA-260 - page 14

    12 1. OPERATORS MANUAL - Read and understand this manual before operation. Keep manual in a safe location for future reference, i.e., operation, maintenance, storage and specifications. 2. SAFETY MANUAL - Read and understand this manual before operation. Keep manual in a safe location as a reference for safe operating techniques. 3. HEDGE CLIPPER S ...

  • Echo HCA-260 - page 15

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 13 S PECIFICA TIONS MO D E L Len gt h 20 Wi d t h 2 5 Heigh t 2 5 W e i g ht (d ry) * 6 E n gin e T y pe A i r c ool ed, t wo- st r o k Bo r e 3 4 St r ok e 2 8 D ispl acem en t 2 5 . 4 Ex h au s t Sy s t em Sp ar k Ar r C a rb ure t o r W a l b ro D ia p hra I gn i t i on Sy st em Fl y wh eel Magn ...

  • Echo HCA-260 - page 16

    14 A SSEMBL Y GEAR HOUSING ASSEMBL Y / DRIVE SHAFT Tools Required: 8mm x 10mm Open End Wrench Parts Required: Power Head/Drive Shaft Assembly and Gear Housing Assembly. NOTE Hedge Clipper Blades are very sharp. Wear gloves to protect hands. 1 . Slide the Gear Housing Assembly on the Drive Shaft. Be certain the Flex Drive Shaft engages the hole in D ...

  • Echo HCA-260 - page 17

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 15 THROTTLE LINKAGE AND IGNITION LEADS 1 . Close choke and remove air filter cover. 2 . Loosen nut (A) and place threaded end of throttle linkage in bracket slot. Finger tighten nut (A). 3 . Place inner cable in slot of carburetor swivel (B) and tighten nut (A). 4 . Check throttle for freedom of mo ...

  • Echo HCA-260 - page 18

    16 Handling Fuel W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to ...

  • Echo HCA-260 - page 19

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 17 EQUIPMENT CHECK Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found. • Check th ...

  • Echo HCA-260 - page 20

    18 O PERA TION W ARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions which can cause serious injury or death. • Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Before starting the unit, equip yourself and ...

  • Echo HCA-260 - page 21

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 19 ST ARTING COLD ENGINE W ARNING DANGER The blades should not move at idle. If blades move, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch - Start/Run. Move stop sw ...

  • Echo HCA-260 - page 22

    20 ST ARTING W ARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. W ARNING DANGER When engine starts, the cutting attachment may move even with the throttle trigger in idle (released) position. 1. Stop Switch - Start/Run. Move stop switch ...

  • Echo HCA-260 - page 23

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 21 STOPPING ENGINE 1. Release Throttle . Allow engine to idle down and blades stop moving with throttle trigger disengaged. 2. Release "Idle Start Interlock Lever" (D) - Move "Stop Switch" to STOP position. W ARNING DANGER The engine does not stop when idle start interlock lever ...

  • Echo HCA-260 - page 24

    22 MAINTENACE INTER V ALS C omp on en t / System M ai nt enanc e Procedu re D a ily o r Bef o r e Use Air Fil t er Cl ean / R epl ace I / C Fu el St rain er C l ean / R epl ace Fu el Lin e I n s pec t / R epl ace I Car bu r et or I n s pect / R ebu i l d/ Re p lac e Ch ok e Sy s t em I n s pec t / Cl ean / R ep l ac e I / C Cool i n g Sy st em I n ...

  • Echo HCA-260 - page 25

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 23 AIR FIL TER Level 1. Tools required: 25 or 50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90030 REPOWER TM Air & Fuel Filter Kit.. 1 . Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated d ...

  • Echo HCA-260 - page 26

    24 W ARNING DANGER Catalytic mufflers operate at extremely high temperatures. Muffler area must be kept clean. Do not perform maintenance on engine or muffler until engine and muffler are completely cool, otherwise serious personal injury may occur. SP ARK PLUG Level 2. Tools Required: Scrench (combination socket wrench and screw driver supplied wi ...

  • Echo HCA-260 - page 27

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 25 1 . Remove spark plug lead. 2 . Remove two (2) muffler cover screws and muffler cover (A). 3 . Remove screw and arm rest (B). 4 . Remove cylinder cover (C). IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins. 5 . Use brush to remove dirt from the cylinder fins. 6. Remove ...

  • Echo HCA-260 - page 28

    26 1 . Remove two (2) muffler cover screws and muffler cover (A). 2 . Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder. 3 . Remove spark arrestor screen cover (B), gasket (C), gasket (D) and screen (E) from muffler body. 4 . Clean carbon deposits from screen and muffler components. NOTE When cleaning carbon deposi ...

  • Echo HCA-260 - page 29

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 27 Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with California Emission Regulations. This carburetor does not have acceleration and high speed adjustment needles. 1 . C ...

  • Echo HCA-260 - page 30

    28 4 . Wipe excess oil from the blade before putting the unit back in service. 5. Check blade tightness. Tighten blade bolts (A) until snug with 10 mm wrench. Loosen bolts 1/2 turn. Hold bolts (A) from turning and tighten locknuts (B) with other 10 mm wrench. Gear Housing Assembly Level 2 Tools required: Grease Gun with Echo Lube TM 14 oz. cartridg ...

  • Echo HCA-260 - page 31

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 29 1 . Loosen gear housing locating screw (A) and mounting screws (C). Remove the gear housing assembly from the drive shaft housing. 2 . Pull the drive shaft (B) from the housing, wipe clean and re-coat with a thin coating [1/2 oz. (15 ml)] of grease. 3. Slide the flexible shaft back in the drive ...

  • Echo HCA-260 - page 32

    30 T ROUBLESHOOTING W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result. Probl em E n g i ne -- s tarts hard E n gi n e - - does n ot st ar t Ca us e En gi n e Cr an k s Fu el at car b u r et or No fu el a ...

  • Echo HCA-260 - page 33

    S HAFT H EDGE C LIPPER O PERA TOR ' S M ANUAL 31 S TORAGE W ARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long T erm Storage (over 30 days ...

  • Echo HCA-260 - page 34

    S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them i ...

  • Echo HCA-260 - page 35

    M ONT AJE INST ALACION DE LA EMPUÑADURA DELANTERA IMPORTANTE Guarde y transporte siempre los cortasetos de eje en una posición horizontal estable. Soporte la caja de engranajes y las hojas de corte para impedir una flexión excesiva que puede causar daños en el accesorio de corte. Instale siempre la tapa de la hoja al transportar o guardar la un ...

メーカー Echo カテゴリー Hair Clippers

Echo HCA-260のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HCA-260の取扱説明書
- Echoの製品カード
- パンフレット
- またはEcho HCA-260の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Echo HCA-260の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Echo HCA-260の取り付け説明書、サービスマニュアル、簡易説明書、またはEcho HCA-260のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Echo HCA-260の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Echo HCA-260デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEcho HCA-260を使用するのを助ける技術的文書のことです。説明書は通常、全てのEcho HCA-260ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Echoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Echo HCA-260の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEcho HCA-260の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Echo HCA-260に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Echo HCA-260デバイスの基本機能を使うにあたってのヒント。 Echo HCA-260のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Echo HCA-260に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEcho HCA-260のメーカー/サービスへの連絡先に関する情報。

Echo HCA-260についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEcho HCA-260の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEcho HCA-260で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)