日本語 dropdown-ico

ICP DAS USA SST-2450の取扱説明書

26ページ 1.84 mb
ダウンロード

ページに移動 of 26

Summary
  • ICP DAS USA SST-2450 - page 1

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 1 SST - 2450 Wireless Modem User ’ s Manua l Warranty All products manufactured by ICP DAS are warranted against defective materials for a period of one year from the date of delivery to the original purchaser. Warning ICP DAS assume s no liability for d amage ...

  • ICP DAS USA SST-2450 - page 2

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 2 Table of Contents 1. Introduction ........................................................................................................... 3 2. Specifications .................................................................................................. ...

  • ICP DAS USA SST-2450 - page 3

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 3 1. Introduction SST - 24 5 0EXT is a spread spectrum radio modem with controlling an RS - 232/RS - 485 interface port. It is designed for data acquisition and control application s between a host and remote sensors. It is also usefu l for those applications wh ...

  • ICP DAS USA SST-2450 - page 4

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 4 2. Specifications Frequency Range: 2.4GHz ( 2410.496MHz ~ 2471.936MHz ) Channel Spacing: 4.096MHz Output Power: 0.1W Transmit po wer : 19dBm 土 1 dBm Modulation technique: GMSK Radio technique: D irect sequence spread spectrum Duplex Mode: TDD (for Full - dup ...

  • ICP DAS USA SST-2450 - page 5

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 5 3. Product D escription 3.1. Pin assignment Radio Modem Frequency Range : 2410~2471MHz Channel Space : 4,096 Mhz Communication Range : 100-300M Interface :RS-232/RS-485 SST-2450 SET GND RX TX GND (Y)DATA+ (G)DATA- (R)+Vs (B)GND (RS-232) (RS-485) 1 10 20 11 ...

  • ICP DAS USA SST-2450 - page 6

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 6 3.2. Block diagram The SST - 2450 wave signal cannot pass through metallic obstacle s. So this produ ct is not suitable for this type of metallic environment . The signal can pass thorough a cement wall, but will be weakened to half its efficiency for every 15 ...

  • ICP DAS USA SST-2450 - page 7

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 7 4. Applications 4.1. Peer to Peer There are three types of peer to peer operational modes to choose from. The following table outlines the settings information and limitation s. Mode Description: 1 In this mode, the SST - 2450 can accept and transmit any signa ...

  • ICP DAS USA SST-2450 - page 8

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 8 4.1.1. PC to PC connections -- Using Mode 1 Full - Duplex Asynchronous Master Baudrate: 9600bps Max. Full - Duplex Asynchronous Slave Baudrate: 9600bps Max. ...

  • ICP DAS USA SST-2450 - page 9

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 9 4.1.2. Connecting a PC to the 7000 module – Using Mode 2 Full - Duplex S ynchronous Master Baudrate: 57600 bps Max. Full - d uplex S ynchronous Slave Baudrate: 57 600bps Max. ...

  • ICP DAS USA SST-2450 - page 10

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 10 4.1.3. Connecting the 7188 Embedded Controller to the 7000 module – Using Mode 3 Both SST - 2450 modules are setting as follows: Half - Duplex S ynchronous Slave Baudrate: 57600 bps Max. ...

  • ICP DAS USA SST-2450 - page 11

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 11 4.1.4. Connecting a PC to a PLC – Using Mode 3 Both SST - 2450 modules settings are as follows: Half - Duplex S ynchronous Slave Baudrate: 57600 bps Max. ...

  • ICP DAS USA SST-2450 - page 12

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 12 4.1.5. Using the 7188 as a Bridge -- Using Mode 3 Both SST - 2450 modules settings are as follows: Half - d uplex S ynchronous Slave Baudrate: 57600 bps Max. ...

  • ICP DAS USA SST-2450 - page 13

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 13 4.2. Network communication 4.2.1. Application 1 All SST - 2450 modules settings are as follows: Half - Duple x S ynchronous Slave Baudrate: 57600 bps Max. ...

  • ICP DAS USA SST-2450 - page 14

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 14 4.2.2. Application 2 All SST - 2450 modules settings are as follows: Half - d uplex S ynchronous S lave Baudrate: 57600 bps Max. Data Format: E,8,1 ...

  • ICP DAS USA SST-2450 - page 15

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 15 5. Quick Start instructions for the SST - 2450 The SST - 2450 is set by using a software utility . By using this tool, you are able to avoid disassembl ing the case. The utility not only provides a setting interface but also a testing interface. When you have ...

  • ICP DAS USA SST-2450 - page 16

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 16 The following screen will then be shown. 1. We recommend installing the software into the default directo ry. However, you may choose a different directory by clicking the “ Change Directory” button and selecting the directory where you want to install th ...

  • ICP DAS USA SST-2450 - page 17

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 17 5.2. SST - 2450 Settings When setting the SST - 2450, you should first use a wire to connect the SET and GND pins. Quickly power off and power on the SST - 2450, then launch the setting software program . There are only 3 steps required to make your settings. ...

  • ICP DAS USA SST-2450 - page 18

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 18 1. Select a COM port from which your SST - 2450 is connected to the PC. In the setting mode, the baud rate must be set at 9600bps and the Line control values must be N , 8,1 . Click the “ Open ” button to open a connection to the device then click the “ ...

  • ICP DAS USA SST-2450 - page 19

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 19 5.3. Te sting the SST - 2450 This tool is for testing the transmissions between two PCs using the SST - 2450. Please note that before you use this function, you must make sure that you have removed the wire that you used to connect the SET and GND pins. The t ...

  • ICP DAS USA SST-2450 - page 20

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 20 6. Troubleshooting Setting error If you are attempting to set your SST - 2450 using the software, but are unable to acc ess the setting tool, the following screen will appear. Follow the steps shown on the error screen. Testing error If you are attempting to ...

  • ICP DAS USA SST-2450 - page 21

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 21 7. Dimension s 111 10.5 Back View Top View From View Side View O4.5X4 56.00 25.00 40.50 7.30 88.50 35.30 33.00 72.00 25.00 58.50 72.00 56.00 29.50 33.00 2-SCREW M3 8 Front View Rear View ...

  • ICP DAS USA SST-2450 - page 22

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 22 8. Din - rail Mounting ...

  • ICP DAS USA SST-2450 - page 23

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 23 9. External Antenna Using an external antenna in conjunction with the SST - 2450 allows the device to be used outdoors. The antenna is even water resistant. Simply replac e the default antenna with an external antenna and you will be able to transmit data acr ...

  • ICP DAS USA SST-2450 - page 24

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 24 9.2. ANT - 8 ( Omni directional ) Gain: 8 dBi Polarization: Linear Power handling: 10 W Impedance: 50 Ohms Connector: SMA Cable: RG - 58, 100cm Gain Pattern Usage Diagram H - Plane Field Patterns V - Plane Field Patterns ...

  • ICP DAS USA SST-2450 - page 25

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 25 9.3. ANT - 12P (Directional) Gain: 12 dBi Pol arization: Linear Power handling: 10 W Impedance: 50 Ohms Connector: SMA Cable: RG - 58, 100cm Gain Pattern Usage Diagram H - Plane Field Patterns V - Plane Field Patterns ...

  • ICP DAS USA SST-2450 - page 26

    SST - 2450 Wireless Modem User ’ s Manual Ver1. 5 , Feb /200 3 , OMH - 0 30 - 10, --- 26 10. Appendix How should I communicate between the SST - 2450 and the SST - 2400? If you want to use the SST - 2400 t o communicate with the SST - 2450, you need to contact the local distributor to get new chip with new firmware. Then refer to Figure 10.1 , Fi ...

メーカー ICP DAS USA カテゴリー Modem

ICP DAS USA SST-2450のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SST-2450の取扱説明書
- ICP DAS USAの製品カード
- パンフレット
- またはICP DAS USA SST-2450の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、ICP DAS USA SST-2450の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、ICP DAS USA SST-2450の取り付け説明書、サービスマニュアル、簡易説明書、またはICP DAS USA SST-2450のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、ICP DAS USA SST-2450の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

ICP DAS USA SST-2450デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがICP DAS USA SST-2450を使用するのを助ける技術的文書のことです。説明書は通常、全てのICP DAS USA SST-2450ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

ICP DAS USAの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. ICP DAS USA SST-2450の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははICP DAS USA SST-2450の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。ICP DAS USA SST-2450に関してこのドキュメントで見つけることができる全てのヒントの目次
3. ICP DAS USA SST-2450デバイスの基本機能を使うにあたってのヒント。 ICP DAS USA SST-2450のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。ICP DAS USA SST-2450に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるICP DAS USA SST-2450のメーカー/サービスへの連絡先に関する情報。

ICP DAS USA SST-2450についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもICP DAS USA SST-2450の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがICP DAS USA SST-2450で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)