English dropdown-ico

Manual Tyan Computer B5103G12S2

87 pages 4.34 mb
Download

Go to site of 87

Summary
  • Tyan Computer B5103G12S2 - page 1

    1 http://www.TYAN.com Tr ansport GS1 2 / / / B 510 3G 1 2S2 Revision 1.00 Copyright © TYAN Computer Corporation, 2004. All rights reserved. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp . All registered and unreg istered trademarks and company names contained in this manual are propert ...

  • Tyan Computer B5103G12S2 - page 2

    2 http://www.TYAN.com 1 Table of Contents Before You Begin ............................................................................ 5 Safety Precautions ........................................................................... 4 1 Introduction .................................................................................................... ...

  • Tyan Computer B5103G12S2 - page 3

    3 http://www.TYAN.com LCD Driver .................................................................................... 30 Intel Application Accelerator ......................................................... 31 ASF Alert Simulation and WatchDog Drivers ............................... 31 ASF (Alert Standard Format) 2.0 SDK ......................... ...

  • Tyan Computer B5103G12S2 - page 4

    4 http://www.TYAN.com 6.3 About ASF 2.0 ............................................................................... 65 Set up Management Console ......................................................... 65 Check Agent and Management Console Link ............................... 66 Obtain Traps and Push Messages .................................. ...

  • Tyan Computer B5103G12S2 - page 5

    5 http://www.TYAN.com Before You Begin T his manual provides hardware - related information of the s ystem for administrators who use i t to develop and host w eb sites. The administrators should be familiar with operating systems and web brow s ers. Depending on the model purchased, your system may com e with pre - installed software. For software ...

  • Tyan Computer B5103G12S2 - page 6

    ...

  • Tyan Computer B5103G12S2 - page 7

    7 http://www.TYAN.com 1 Introduction Congratulations on purchasing the system. This chapter introduces the features and functions of the product. 1.1 Unpacking After unpacking the shipping carton, you should find these standard items: P/N 431728700002 1× MiSERVER - WS11 2 R case kit P/N 411728700101 (pre - installed) 1× S 5103GNNR motherboard P/N ...

  • Tyan Computer B5103G12S2 - page 8

    8 http://www.TYAN.com And the foll owing accessories : P/N 451715600031 1× rail kit P/N 343728700001 1× heatsink 1× primary IDE cable 1× secondary IDE cable 1× p rimary serial ATA cable 1× secondary serial ATA cable 1× HDD power to pinheader cable 2× SATA power cable 4× rubber feet 2× power cord (USA and Germany) 1× B5103 User ’ s Manu ...

  • Tyan Computer B5103G12S2 - page 9

    9 http://www.TYAN.com 1.2 Specifications NOTE: Specifications are subject to change without notice. Processor • Single s ocket 478 • Intel  Pentium 4 Northwood/Prescott processor • Supports 533 /800 MHz FSB Chipset • Intel 875P MCH • MCH+ICH - 5R • SMC L PC 47 M172 Super I/O chip Memory • T wo 64 - bits wide DDR data channels • S ...

  • Tyan Computer B5103G12S2 - page 10

    10 http://www.TYAN.com 1.3 System View Front View Ref Component Description Œ Power Button Turns the power on and off (soft - off). • Power Indicator Glows green when the power is on . Ž LAN1 Indicator Indicates a network connection on LAN1 (external c onnection). • LAN2 Indicator Indicates a network connection on LAN2 (internal connection). ...

  • Tyan Computer B5103G12S2 - page 11

    11 http://www.TYAN.com Rear View Ref Component Description Œ Ventilation Openings Maintain proper operating tem perature. Do not cover or block the openings. • Power Connector Connects the power cord . Ž Power Switch Turns the main power of the system on and off. • LAN 1 Connector C onnects the LAN cable for in ternal network conne ction . ? ...

  • Tyan Computer B5103G12S2 - page 12

    ...

  • Tyan Computer B5103G12S2 - page 13

    13 http://www.TYAN.com 2 Hard ware Installation This chapter , which is divided into two sections, provides instructions on the hardware installation of the sy stem . System Assembly section illustrates how to assembl e each component of the system . Rack Mounting section describes the procedures for mounting the system into the rack. You can use t ...

  • Tyan Computer B5103G12S2 - page 14

    14 http://www.TYAN.com System Assembly Flowchart The following flowchart shows the basic procedures of system assembly: FINISH START INSTALL SYSTEM MEMORY REMOVE CA BINET COVER INSTALL C PU AND HEATSINK INSTALL HARD DISK DRIVE CONNECT H ARD DISK DRIVE CABLE AND POWER CORD CHECK IF ALL PARTS ARE PROPERLY CONNECTED REPLACE CA BINET COVER ...

  • Tyan Computer B5103G12S2 - page 15

    15 http://www.TYAN.com 2.1 S ystem Assembly When insta lling a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. Safety Considerations l Static electricity can destroy electronic devices. Whenever you handle an option outside of its protective p ackaging, first discharge any static ...

  • Tyan Computer B5103G12S2 - page 16

    16 http://www.TYAN.com 3. L ift the socket arm up to the vertical position. Align the new CPU so its Pin 1 corner (beveled corner) is at the Pin 1 corner of the socket. 4. Insert the CPU pins into the socket. Press the arm downward to the horizontal position. You will feel some resistance while doing so. This is normal as the pressure starts to sec ...

  • Tyan Computer B5103G12S2 - page 17

    17 http://www.TYAN.com 6. Replace the cabinet cover. Installing System Memory Your system has four 184 - pin DIMM (Dual In - line Memory Module) sockets to support a max imum of 4 G B. You must follow these requirements for the DIMM to be used with the system: l Unbuffered DDR - SDRAM ( Double Data Rate Synchronous DRAM) with ECC l PC 21 00/PC 2700 ...

  • Tyan Computer B5103G12S2 - page 18

    18 http://www.TYAN.com 3. To install the DIMM, make sure the retaining clips are in the unlocked position, then align the DIMM ’ s notched end with the socket ’ s corresponding end and firmly insert the DIMM into the socket. Finally p ush the retaining clips inwards to lock the DIMM in place. 4. Replace the cabinet cover. Installing a Hard Disk ...

  • Tyan Computer B5103G12S2 - page 19

    19 http://www.TYAN.com 4. Fit the bracket with a hard disk drive bac k into place and secure with one screw. If using an Ultra ATA/100 hard disk drive, c onnect the corresponding end of the included HDD power to pin header cable to the motherboard ( Œ ) and the other end to the hard disk drive ( • ) . Connect the included prim ary IDE data cable ...

  • Tyan Computer B5103G12S2 - page 20

    20 http://www.TYAN.com 5. Replace the cabinet cover. 6. You can create or rebuild RAID for the hard disk drive (see chapter 6 for information). 2.2 Adding a CD Drive You will need to use a CD drive when installing an operating system and its corresponding drivers (see chapter 3). WARNING : You are advised not to make frequent connection and disconn ...

  • Tyan Computer B5103G12S2 - page 21

    21 http://www.TYAN.com Without a Secondary Ultra ATA/100 Hard Disk Drive Installed 1. Remove the cabinet c over (see the previous section in this chapter). 2. Connect one end of the data cable to the secondary IDE connector and the other end to the re ar of the CD drive ( Œ ). 3. Connect the power cord to the rear of the CD drive ( • ). NOTE : Y ...

  • Tyan Computer B5103G12S2 - page 22

    22 http://www.TYAN.com You should find these st andard items: l 2 mounting ears l 2 rack slides (inner and outer slides) l 4 post slide mount adapters l hex screws (+) and hex nuts (for outer slides) l hex screws (for slide mount adapter – dark colored) Cabinet Slides and Ears 1. Attach the mounting ears to the side near the front of the cabinet. ...

  • Tyan Computer B5103G12S2 - page 23

    23 http://www.TYAN.com 4. Attach a post slide mount adapter to the front end of the outer slide by securing 2 sets of hex screws and hex nuts together. 5. Attach a post slide mount adapter to the rear end by moving the inner rails to expose the scr ew holes. Do the same for the other outer slide. 6. Attach the newly assembled outer slide with the p ...

  • Tyan Computer B5103G12S2 - page 24

    24 http://www.TYAN.com Locking Tab To prevent the system chassis from sliding on its rails, secure the system cabinet to the rack with a screw on each of the mounting ears Ž (optional – refe r to the figure above). 2.4 Setting Up the System To use the s ystem, you need : l A 10Base - T, 10/100Base - TX, 100Base - TX or 1 000 Bas e - T TCP/IP - b ...

  • Tyan Computer B5103G12S2 - page 25

    25 http://www.TYAN.com Making the Connection 1. Connect one end of a Category 5 Ethernet cable to the LAN1 connector on the system and the other end to the network socket that connects to the external network. 2. Connect one end of a Category 5 Ethernet cable to the LAN2 connector on the sy stem and the other end to the network socket that connects ...

  • Tyan Computer B5103G12S2 - page 26

    26 http://www.TYAN.com 7. Press the power button to turn on the system. The h ard disk drive spins up, the fan turns on, and the LCD screen lights up. A number of status messages are displayed on the screen during the boot process. CAUTION: It is important to follow the proper power - down procedure for turning off the system. ...

  • Tyan Computer B5103G12S2 - page 27

    27 http://www.TYAN.com 3 S oft ware Installation You need to install an operating system and its corresponding software drivers using the CD supplied with your system. The drivers are required for taking full advantage of its unique features. As of the publication of this User ’ s Manu al, the drivers presently available on the CD and the OS supp ...

  • Tyan Computer B5103G12S2 - page 28

    28 http://www.TYAN.com Driver OS Available on CD SuSE Linux 8.1 Not Available Turbo Linux 8 Not Available ASF Alert Simulation FreeBSD 4.7 Not Available Windows 2000 ü Windows 2000 SBS ü Windows 2003 ü Windows 2003 SBS ü Windows XP ü RedHat Linux 9.0 Not Available SuSE Linux 8.1 Not Available Turbo Linux 8 Not Available ASF (Alert Standard For ...

  • Tyan Computer B5103G12S2 - page 29

    29 http://www.TYAN.com 3.1 In stallation Instructions for Windows Windows Installation Notes Proceed with the normal Windows operating system installation but i f you are installing Windows on to a Serial ATA hard disk drive with RAID function, do the following first : 1. Create a RAID driv er floppy disk by inserting a blank floppy disk and the dr ...

  • Tyan Computer B5103G12S2 - page 30

    30 http://www.TYAN.com 2. Run the wxp-ragex1-5-10-2600-6009.exe program in the ATI_RageXL XP directory. 3. Follow the onscreen instructions to complete the installation. 4. When finished installing, choose the “Yes” option to reboot and click “Finish” to restart your system. The driver should now be loaded. LAN Driver 1. Insert the driv ...

  • Tyan Computer B5103G12S2 - page 31

    31 http://www.TYAN.com Whe n installation ask s for the CD, just click " OK " and browse the path again to LCDGS12WindowsdriverLCDDriver.sys , th e n click Open - > OK to finish the LCD driver installation. 3. Sta rt the LCD s ervice in Windows Operating System For Windows 2000 Small Business Server system, run LCD GS12Windows ...

  • Tyan Computer B5103G12S2 - page 32

    32 http://www.TYAN.com Clic k on “ Have Disk ” to browse and point the folder to the driver location at ASFWindowsdriverASF_Simulationhwdriverchecked.inf and click Open - > OK . Wh en installation ask s for the CD, just click on "OK" and browse the path again to ASFWindowsdriverASF_Simulation th e n click on Open - > O ...

  • Tyan Computer B5103G12S2 - page 33

    33 http://www.TYAN.com 3.2 Installation Instructions for Linux (RedHat /SuSE/Turbo Linux) NOTE: Do not allow USB devices to be hot p lugged during installation of the Linux operating system . RedHat Linux 9.0 Installation Notes Proceed with the normal installation of RedHat Linux 9.0 operating system. If you are using the SMP kernel, in order to al ...

  • Tyan Computer B5103G12S2 - page 34

    34 http://www.TYAN.com 4. Use the command uname – r to check which kernel the system is using. If the kernel is 2.4.18-5smp , modify the file /boot/kernel.h as follows: #define __BOOT_KERNEL_SMP 1 If you are using the SMP kernel, in order to allow a complete system shutdown, then perform the following : 1. M odify the /boot/grub/ grub.conf by add ...

  • Tyan Computer B5103G12S2 - page 35

    35 http://www.TYAN.com LCD Driver 1. Insert the driver CD into the CD drive. 2. Copy MiSM_LLCDxx_for_yyy.tar.gz of the /LCD/GS12/Linux/ directory to the directory of your choice (where xx refers to the version and yyy refers to the operating system). 3. Un tar/un zip archiv e: tar zxf MiSM_LLCD xx_for_yyy.tar.gz . 4. Change to the driver SRC direct ...

  • Tyan Computer B5103G12S2 - page 36

    36 http://www.TYAN.com 3. Un tar/un zip archive: tar xfvz asfm-x.x.tar.gz . 4. Change to the driv er directory: cd asfm-x.x . 5. Install the WatchDog driver: make make install . 3.3 Installation Instructions for FreeBSD 4.7 NOTE: Do not allow USB devices to be hot plugged during installation of the Linux operating system . FreeBSD 4.7 Installation ...

  • Tyan Computer B5103G12S2 - page 37

    37 http://www.TYAN.com Then save and exit . /usr/sbin/config MYKERNEL cd ../../compile/MYKERNEL make depend make make install vi /etc/rc A dd the line apm -e 1 before the last line exit 0 . T hen save and exit . Reboot the system. Y ou can now use the new kernel . Run the command halt -p to shutdown the system completely . LAN Driver NOTE: To compi ...

  • Tyan Computer B5103G12S2 - page 38

    38 http://www.TYAN.com dev/em/if_em_hw.c optional em Remove the following lines from the /usr/src/sys/conf/files.i386 file if they exist: dev/em/if_em_fxhw.c optional em dev/em/if_em_phy.c optional em Edit the kernel configuration file (i .e., GENERIC or MYKERNEL ) in /usr/src/ sys/i386/conf and ensure the following line is present: device em Compi ...

  • Tyan Computer B5103G12S2 - page 39

    39 http://www.TYAN.com USB Floppy Drive Usage If your U SB floppy drive cannot be used normally, please add one line on /etc/sysctl.conf : kern.cam.da.no_6_byte=1 . Then reboot your system. 3.4 Installation Instructions for Solaris 9 Solaris 9 Installation Notes Proceed with the normal Solaris 9 operating system installation but since Serial ATA co ...

  • Tyan Computer B5103G12S2 - page 40

    ...

  • Tyan Computer B5103G12S2 - page 41

    41 http://www.TYAN.com 4 Using the LCD Console This chapter tells you how to use the LCD console to make various system configurations . 4.1 Configuring the System After you have made the network and power connections, you can configure the network settings using the LCD console . Before You Begin NOTE : To take advantage of the LCD console f eatur ...

  • Tyan Computer B5103G12S2 - page 42

    42 http://www.TYAN.com The Down arrow button decreases the digit located at the cursor position. The S (Select) button accepts the data entered or selects the option displayed. The C (Cancel ) button cancels the data entered or the option displayed . 4.2 Setting the Configuration For Windows Press the correspondin g button according to the number o ...

  • Tyan Computer B5103G12S2 - page 43

    43 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow four (4) times HW Monitor Display Upon each succeeding press of the Right arrow, the value of the following appear, depending on your settings under HW Monitor List Configure (down arrow sixth time – see below): Do you want to display? (default is Yes ) CPU Temp Local Temperature System ...

  • Tyan Computer B5103G12S2 - page 44

    44 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow seven (7) times Performance List Configure Upon each succeeding press of the Right arrow, the following appears. Select which value(s) to di splay under Performance Display (down arrow fifth time – see above): Do you want to change? (default is Yes ) CPU Usage Memory Load Total Memory Av ...

  • Tyan Computer B5103G12S2 - page 45

    45 http://www.TYAN.com 4.3 Setting the Configuration For Linux Press the corresponding but ton according to the number of times specified on the following tables, and you will see the corresponding prompt . NOTE: If you press the C (Cancel) button at any time to cancel the configuration, you must go through the entry process for a particular se tti ...

  • Tyan Computer B5103G12S2 - page 46

    46 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow five (5) times HW Monitor Display Upon each succeeding press of the Right arrow, the value of the following appear, depending on your settings under HW Monitor List Configure (down arrow eighth time – see below): HWM Display (default is Yes ) VCC 2.6V VCCP VCC 3.3V VCC 5V Fan 1 Fan 2 Fan ...

  • Tyan Computer B5103G12S2 - page 47

    47 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow nine (9) times Performance List Configure Upon each succeeding press of the Right arrow, the following appears. Select which value(s) to display under Performance Display (down arrow sixth time – see above): Perfor Config (default is Yes ) CPU Usage Memory Usage Disk Usage ETH0 Flow Spee ...

  • Tyan Computer B5103G12S2 - page 48

    48 http://www.TYAN.com 4.4 Setting the Configuration For FreeBSD Press the corresponding button according to the number of times specified on the following tables, and you will see the corresponding prompt . NOTE: If you press the C (Cancel) button at any time to cancel the configuration, you must go through the entry process for a particular setti ...

  • Tyan Computer B5103G12S2 - page 49

    49 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow five (5) times HW Monitor Display Upon each succeeding press of the Right arrow, the value of the following appear, depending on your settings under HW Monitor List Configure (down arrow eigh th time – see below): HWM Display (default is Yes ) Temp1 Temp2 Temp3 Rot1 Rot2 Rot3 VC0 VC1 V3. ...

  • Tyan Computer B5103G12S2 - page 50

    50 http://www.TYAN.com KEY PRESS PROMPT FUNCTION Down arrow nine (9) times Performance List Configure Upon each succeeding press of the Right arrow, the following appears. Select which value(s) to display under Performance Display (down arrow sixth time – see above): Perfor Config (default is Yes ) CPU Usage Memory Usage Disk Usage em0 Flow Speed ...

  • Tyan Computer B5103G12S2 - page 51

    51 http://www.TYAN.com 5 BIOS Setup 5.1 BIOS Setup Program BIOS Setup (SCU or Setup Configuration Utility) is a program for configuring the BIOS (Basic Input/Output System) settings of the system. You need to run the BIOS Setup program when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory defa ...

  • Tyan Computer B5103G12S2 - page 52

    52 http://www.TYAN.com Key Function Enter Pops up an option window for the highlighted field. Esc 1) Returns to the mai n menu from a sub - menu. 2) Exits Setup. F9 Restores the Setup defaults. F10 Saves changes and exits Setup. Main Menu The Main menu contains the basic configuration settings of your system. System Time sets the system time (Hour, ...

  • Tyan Computer B5103G12S2 - page 53

    53 http://www.TYAN.com Legacy USB Support enables or disables support for Legacy Universal Serial Bus in non - USB - aware operating systems like DOS. Spread Spectrum enables or disables the S pread S pectrum functi on to reduce the EMI (Electro - Magnetic Interference) effect . Advanced Chipset Control Graphics Aperture sets the memory size of AGP ...

  • Tyan Computer B5103G12S2 - page 54

    54 http://www.TYAN.com CAUTION : Set this item to disabled before installing an operating system, running Fdisk or Format program, or when re - installing software. Otherwise, the intended action will fail . Virus Check Reminder displays the virus check reminder message during system boot up. System Backup Reminder displays the system back up remin ...

  • Tyan Computer B5103G12S2 - page 55

    55 http://www.TYAN.com Fan Mode Configuration allow s you to select the system f an ’s working mode . When set at Disabled (default) , a ll system fans will run at full speed . When set at Smart mode , the fan will autom atically adjust its speed according to the set temperature . The advantages of choosing Smart mode are reduced noise, reduced w ...

  • Tyan Computer B5103G12S2 - page 56

    56 http://www.TYAN.com 5.2 Resetting BIOS Setup When you want to reset the BIOS configuration, you need to change the jumper setting. See the next figure for jumper location and the table that follow for jumper definition. CAUTION: Jumpers not describ ed in this section are reserved for factory use only. Do not change the default settings. Jumper D ...

  • Tyan Computer B5103G12S2 - page 57

    57 http://www.TYAN.com 6 Using RAID and ASF 2.0 6.1 About RAID NOTE: You need to install two Serial ATA hard disk drive and running Windows XP or Windows 2000 in order for your system to support RAID (Redundant Array of Inexpensive Disk). The purpose of RAI D is to combine multiple small, inexpensive disk drives into an array of disk drives that ap ...

  • Tyan Computer B5103G12S2 - page 58

    58 http://www.TYAN.com 6.2 Creating an Array 1. Make sure that you have installed the Intel Application Accelerator program (refer to chapter 3 ) . Also, you need to install two Serial ATA disk drives to the motherboard (refer to chapter 7 ). 2. Boot up with Windows 2000 or Windows XP. 3. Run the Intel Application Accelerator program . 4. Create yo ...

  • Tyan Computer B5103G12S2 - page 59

    59 http://www.TYAN.com 2. Select RAID 0 under the item Select RAID Level , then click on Next . 3. Click on Yes (Y) to continue . ...

  • Tyan Computer B5103G12S2 - page 60

    60 http://www.TYAN.com 4. Click on Create to create the new RAID volume . 5. Click on OK to finish . ...

  • Tyan Computer B5103G12S2 - page 61

    61 http://www.TYAN.com Creating a Sec urity Array (RAID 1) 1. With the Intel Application Accelerator program running, select RAID , then click on Create Volume Manually . 2. Select RAID 1 under the item Select RAID Level , then click on Next . ...

  • Tyan Computer B5103G12S2 - page 62

    62 http://www.TYAN.com 3. Click on Yes (Y) to continue . 4. Click on Yes (Y) to cont inue . ...

  • Tyan Computer B5103G12S2 - page 63

    63 http://www.TYAN.com 5. Click on Create to create the new RAID volume . 6. Click on OK to finish. Creating RAID With an Existing Data Drive Use this method if you have a Serial ATA disk drive that already contains data or is the boot device in your system. You will need another Serial ATA disk drive of identical or larger storage capacity. ...

  • Tyan Computer B5103G12S2 - page 64

    64 http://www.TYAN.com 1. With the Intel Application Accelerator program running, select RAID , then click on Create Volume from Existing Disk . 2. Select a source disk, then click on Next . 3. Then, follow the steps outlined in the previous sections Creating an Array for Performance (RAID 0) and Creating a Security Array (RAID 1). ...

  • Tyan Computer B5103G12S2 - page 65

    65 http://www.TYAN.com 6.3 About ASF 2.0 NOTE: You need to be running Windows XP , Windows 2000 or Windows 2003 in order for your system to support ASF 2.0 (Alert Sta ndard Format). ASF 2.0 enables remote systems to activate security features as well as control your system (e.g., power on, power off, system reset, power cycle, etc.) whether with or ...

  • Tyan Computer B5103G12S2 - page 66

    66 http://www.TYAN.com Check Agent and Management Console Link 1. To check the link between the Agent and the Management Console, ping each other ’ s IP address ( ipconfig and ping ). 2. Run the alertAPP.exe file located on the Agent ’ s system and log in directly without having to type anythin g, then check that the following configurations ar ...

  • Tyan Computer B5103G12S2 - page 67

    67 http://www.TYAN.com 3. Run the ASFMgmtConsole.exe f ile on the Management Console, then check if the data from the Agent is correct. ...

  • Tyan Computer B5103G12S2 - page 68

    68 http://www.TYAN.com Obtain Traps and Push Messages 1. Run AlertApp to set Heartbeat . 2. Run ASFMgmtConsole to obtain Alert from the Agent. ...

  • Tyan Computer B5103G12S2 - page 69

    69 http://www.TYAN.com Remote Control 1. To generate Key from Management Console , run ASFMgmtConsole to generate the Administrator Key . 2. Save the Key from Management Console into a floppy disk. 3. Run AlertApp to load the Security Key to the Agent. ...

  • Tyan Computer B5103G12S2 - page 70

    70 http://www.TYAN.com 4. Run AlertApp to select the Remote Control functions supported by the system. 5. Run ASFMgm tConsole to select and execute Remote Control operations (send secured RMCP). ...

  • Tyan Computer B5103G12S2 - page 71

    71 http://www.TYAN.com 7 Expanding the System You can expand the capabilities of the system by adding or upgrading internal devices . When install ing a device, be sure to read the instructions accompa nying the device together with the relevant section in this chapter. 7.1 Opening the Cover CAUTION: l Static electricity can destroy electronic devi ...

  • Tyan Computer B5103G12S2 - page 72

    72 http://www.TYAN.com 7.2 Installing an Expansion Card Your system support s one PCI slot located on a ri ser card. You can install a PCI expansion card for additional or enhanced functions. Follow this procedure to install an expansion card: 1. Before you purchase a PCI expansion card to add to the system, make sure that the card is less than 7 i ...

  • Tyan Computer B5103G12S2 - page 73

    73 http://www.TYAN.com 5. Replace the cabinet cover. NOTE : According to the standard X86 structure , there is only 128 k (C0000h - DFFFFh) shadow RAM for system option ROM. For thi s system, the RAID card option ROM engross es 64 k, the onboard ATI VGA card engross es 32 k, the onboard LAN engross es more than 10 k, so the remain ing space for opt ...

  • Tyan Computer B5103G12S2 - page 74

    74 http://www.TYAN.com 3. Secure the hard disk drive to the bracket w ith four bottom screws. 4. Fit the bracket with the hard disk drive back into place and secure with one screw. 5. If using an Ultra ATA/100 hard disk drive, c onnect one end of the included secondary IDE data cable to the secondary IDE connector (see figure abo ve ) and the other ...

  • Tyan Computer B5103G12S2 - page 75

    75 http://www.TYAN.com 6. You can create RAID for the hard disk drives (see Chapter 6 for information). ...

  • Tyan Computer B5103G12S2 - page 76

    ...

  • Tyan Computer B5103G12S2 - page 77

    77 http://www.TYAN.com 8 System Parts Replacement In case the need arises, y ou can replace various system components. When removing and install ing a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. 8.1 Opening th e Cover CAUTION: l Static electricity can destroy electronic device ...

  • Tyan Computer B5103G12S2 - page 78

    78 http://www.TYAN.com 8.2 Removing the Front Bezel Care must be taken to ensure that the latches on the front bezel used to attach it to the system chassis does not break . Follow this procedure to detach it from the system chassis: 1. Open the cabinet c over (see the previous section in this chapter ). 2. Remove the primary hard disk drive (see c ...

  • Tyan Computer B5103G12S2 - page 79

    79 http://www.TYAN.com Reverse t he above sequence when installing the new button board . 8.4 Replacing the Fan There are two fans located at the front of the system. To replace either one, follow these procedures. 1. Remove the cabinet c over (see the previous section in this chapter ). 2. Remove th e front bezel (see the previous section in this ...

  • Tyan Computer B5103G12S2 - page 80

    80 http://www.TYAN.com 8.5 Replacing the USB Board The USB board contains the circuitry for the two USB ports located on the system ’ s front panel. To replace it, follow these procedures. 1. Remove the cabinet c over (see the previous section in this chapter ). 2. Remove the front bezel (see the previous section in this chapter ). 3. Remove the ...

  • Tyan Computer B5103G12S2 - page 81

    81 http://www.TYAN.com Reverse the above sequence when installing the new LCD module . 8.7 Replacing the Power Supply To replace the system ’ s power supply, follow these procedures. 1. Remove the cabinet c over (see the previous section in this chapter ). 2. Remove the secondary hard disk drive (see chapter 7 on Adding a Secondary Hard Disk Driv ...

  • Tyan Computer B5103G12S2 - page 82

    82 http://www.TYAN.com Reverse the above sequence when installing the new power supply . 8.8 Replacing the Blower To rep lace the system ’ s blower, follow these procedures. 1. Remove the cabinet c over (see the previous section in this chapter ). 2. Remove the two screws securing the blower to the system chassis and detach the blower to pin - he ...

  • Tyan Computer B5103G12S2 - page 83

    83 http://www.TYAN.com 5. Remove the heatsink screws following a diagonal s equence to detach the heatsink and remove the CPU from its socket. 6. Detach the DIMM from the socket on the motherboard. 7. Detach the riser card from the PCI slot on the motherboard. 8. Remove the four hex screws on the serial and VGA ports on the rear panel. 9. R emove t ...

  • Tyan Computer B5103G12S2 - page 84

    ...

  • Tyan Computer B5103G12S2 - page 85

    85 http://www.TYAN.com 9 Appendix Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagti g h åndtering. Udskiftning m å kun ske med batteri af samme fabrikat og type. Lev ér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt ...

  • Tyan Computer B5103G12S2 - page 86

    86 http://www.TYAN.com FRENCH ATTENTION: II y a danger d ’ explosion s ’ il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d ’ un type équivalent recommand é par le constructeur. Mettre au rebut les batteries usag ées conformément aux instructions du fabricant. Technical Support If a pro ...

  • Tyan Computer B5103G12S2 - page 87

    87 http://www.TYAN.com Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure ) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including ...

Manufacturer Tyan Computer Category Computer Hardware

Documents that we receive from a manufacturer of a Tyan Computer B5103G12S2 can be divided into several groups. They are, among others:
- Tyan Computer technical drawings
- B5103G12S2 manuals
- Tyan Computer product data sheets
- information booklets
- or energy labels Tyan Computer B5103G12S2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tyan Computer B5103G12S2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tyan Computer B5103G12S2, service manual, brief instructions and user manuals Tyan Computer B5103G12S2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tyan Computer B5103G12S2.

Similar manuals

A complete manual for the device Tyan Computer B5103G12S2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tyan Computer B5103G12S2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tyan Computer B5103G12S2.

A complete Tyan Computer manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tyan Computer B5103G12S2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tyan Computer B5103G12S2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tyan Computer B5103G12S2, that we can find in the current document
3. Tips how to use the basic functions of the device Tyan Computer B5103G12S2 - which should help us in our first steps of using Tyan Computer B5103G12S2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tyan Computer B5103G12S2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tyan Computer B5103G12S2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tyan Computer B5103G12S2?

Use the form below

If you did not solve your problem by using a manual Tyan Computer B5103G12S2, ask a question using the form below. If a user had a similar problem with Tyan Computer B5103G12S2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)