-
Hans Grohe Talis S 32111XX1 - page 1
T alis S² 32110XX1 32112XX1 T alis S² 32111XX1 32113XX1 Installation Instructions / W arranty ...
-
Hans Grohe Talis S 32111XX1 - page 2
2 T echnical Information Recommended water pressure 15 - 72 psi Max. water pressure 116 psi Max. hot water temp. 176 o F* Recommended hot water temp. 120 o F - 140 o F* Flow rate 1.6 gpm Batter y (32210/32212 only) CR-P2 / 6 V Lithium Automatic shutoff after 1 min. *Please know and follow all local plumbing codes when setting the temperature on the ...
-
Hans Grohe Talis S 32111XX1 - page 3
3 Do not install this faucet on a sink with a raised lip. Do not bend or twist the supply hoses! ok! no! ...
-
Hans Grohe Talis S 32111XX1 - page 4
4 Installation notes • Flush the hot and cold supplies thoroughly before installing the faucet. Damage to the faucet caused by debris is not covered under the warranty . • The hot and cold supplies should be of equal pressure. • The faucet should not be used with a con- tinuous flow water heater . • Do not install the faucet on a sink with ...
-
Hans Grohe Talis S 32111XX1 - page 5
5 Installation Position the faucet on the sink or countertop (1). Install and tighten the mounting nut (2). T ighten the tensioning screws (3). Connect the 3/8” adapters to the stops (4). Connect the hoses to the adapters (5). T ighten the hoses with two wrenches, as shown, to prevent the hoses from twisting. 1 2 3 4 5 ...
-
Hans Grohe Talis S 32111XX1 - page 6
6 T emperature adjustment - 32111XX1 / 32113XX1 only T urn the water supplies off (1). Disconnect the faucet power cable from the batter y pack or AC power pack (2). Remove the screw from the rear of the faucet (3). Connect the faucet power cable to the batter y pack or AC power pack (1). Plug the AC power pack in. T urn the hot and cold supplies o ...
-
Hans Grohe Talis S 32111XX1 - page 7
7 Remove the faucet body (1). T urn the temperature screw for ward to make the water cooler , backward to make it warmer (2). Dr y any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). T urn the water supplies on (3). Reconnect the power cable (4). W ait 30 seconds (1). Place your hand in front ...
-
Hans Grohe Talis S 32111XX1 - page 8
8 Battery replacement -- models 32110XX1 / 32111XX1 only If the LED in the sensor window flashes, the batter y is low , but the faucet can still be used. If the LED lights continuously , the batter y must be changed before the faucet can be used. Remove the four screws and the batter y pack cover . Remove the old batter y (1). Install the new batte ...
-
Hans Grohe Talis S 32111XX1 - page 9
9 Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and the filters (b). T urn the water supplies off (1). Disconnect the power cable (2). Unscrew the aerator (a) with the ser vice key . Disconnect the hot and cold supply hoses from the adapters. Remove the filters (b). At another sink, rinse ...
-
Hans Grohe Talis S 32111XX1 - page 10
10 W ait 30 seconds (1). Place a hand in front of the sensor to turn the faucet on (2). ...
-
Hans Grohe Talis S 32111XX1 - page 11
11 Cleaning The faucet may be turned off temporarily so that the sink may be cleaned. Cover the sensor window with a hand for approximately 10 seconds. The faucet will turn off for approximately 60 seconds, so that the sink may be cleaned. The LED in the sensor window will flash. When the LED no longer flashes, the faucet may be used normally . ...
-
Hans Grohe Talis S 32111XX1 - page 12
12 Reduce the sensor range The sensor is set for maximum range at the factor y . If the faucet is used on a ver y small or highly reflective lavator y , the sensor range may be reduced by ap- proximately 2”. Disconnect the power cable for approximately 10 seconds (1). Reconnect the power cable (2). The LED will blink once to indicate that it is i ...
-
Hans Grohe Talis S 32111XX1 - page 13
13 Replacement Parts 1 aerator 98802XX0 2 fixing set 13961000 3 AC adapter 4 batter y , lithium CR-P2 / 6V 5 batter y box 98801000 6 connection hose 98809000 7 electronics 98803000 8 check valve 96456000 9 aerator ser vice key 98808000 Maintenance note : the check valves (item #8) should be removed and checked yearly . XX = color 00 = chrome 82 = b ...
-
Hans Grohe Talis S 32111XX1 - page 14
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe Talis S 32111XX1 - page 15
15 the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A. Conditions, malfunctions ...
-
Hans Grohe Talis S 32111XX1 - page 16
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No. 90423121 • Revised 11/2007 ...
Do you have a question concerning Hans Grohe Talis S 32111XX1?
Use the form below
If you did not solve your problem by using a manual Hans Grohe Talis S 32111XX1, ask a question using the form below. If a user had a similar problem with Hans Grohe Talis S 32111XX1 it is likely that he will want to share the way to solve it.