English dropdown-ico

Manual Stanton DJLab.3

12 pages 6.52 mb
Download

Go to site of 12

Summary
  • Stanton DJLab.3 - page 1

    S T A N T O N M A G N E T I C S , I N C + 1 9 5 4 - 6 8 9 - 8 8 3 3 w w w . s t a n t o n d j . c o m information@stantondj.c om DJLab.3 OWNER'S MANUAL ...

  • Stanton DJLab.3 - page 2

    IMPORTANT TO SAFETY 1. Read these Instructions 2. Keep these Instructions 3. Heed all W arnings 4. Follow all Instructions 5. Do not use this apparatus near w ater 6. Clean only with dry cloth 7. Do not block any ventilation ope nings. Install in accordance with the manufacturer ’s instructions. 8. Do not install near any heat sources such as rad ...

  • Stanton DJLab.3 - page 3

    LINE VOLTAGE SELECTION 1 15V 230V 1) The desired volt age of your turntable may be set with the VOL T AGE SELECT OR switch on the rear panel of the main unit, using a screwdriver . 2) Do not twist the VOL T AGE SELECTOR switch wi th excessive force as this may cause damage. 3) If the VOL T AGE SELECTOR switch does not mo ve smoothly contact a quali ...

  • Stanton DJLab.3 - page 4

    M.202 CONTENTS 1) Input fader - Controls individual source levels/volume (channels) in the mix. 2) Input toggle switch - Selects which sou rce will be active based on what you have connected to the rear panel input section (phono/line). 3) Channel EQ - Adjust s the high, mid and low frequency levels of the input channels for good sound. 4) Channel ...

  • Stanton DJLab.3 - page 5

    QUICK SETUP DIA GRAM S tudy this setup diagram. Make sure all faders are at "zero" and all devices are off. First, conne ct all input sources. Next, connect your microphone a nd monitor headpho nes. Finally , connect the stereo outputs to the pow er amplifier(s) and/or a udio receivers such as t ape decks. Plug your mixer into AC po we r ...

  • Stanton DJLab.3 - page 6

    SPECIFICA TIONS M.202 INPUT / OUTPUT IMPEDANCE & SENSITIVITY : LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV PHONES MORE THAN +21dBV CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2 ...

  • Stanton DJLab.3 - page 7

    CONNECTIONS 1) Connect the power cord to an AC outlet. 2) Connect the RCA cable to the PHONO input of your mixer. You can also use a line input by setting the phono/line switch at the rear of the turntable to Line. Note: This turntable has separate analog and digital circui ts. If you are looking for a purely analog signal, use the Phono output. Fo ...

  • Stanton DJLab.3 - page 8

    T .80 TURNT ABLE CONTENTS 1) S tart/S top 2) S trobe Dots 3) Slipmat 4) Center S pindle 5) Motor ON/OFF Switch 6) Platter Revolution S peeds (RPM) 7) T arget Light Base 8) Key Lock 9) Pitch Lock 10) Pitch Slider 11) Headshell Locking Nut 12) T onearm 13) Pitch Select 14) T one Arm Base 15) Counterweight 16) 45-rpm Adaptor Holder 17) Extra S tylus H ...

  • Stanton DJLab.3 - page 9

    SPECIFICA TIONS T .80 POWER SOURCE AC 100V , 50/60Hz (For Japan) AC 1 10V , 60Hz (For T aiwan) AC 120V , 60Hz (For U.S.A.,Canada,Mexico) AC 220V , 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V , 60Hz (For Philippines) AC 230V , 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V , 50Hz (For Australia,U.K.) POWER CONSUMPTIO ...

  • Stanton DJLab.3 - page 10

    St anton Magnetics, Inc. – W arrant y Provision – Returns for Rep airs or Replacement W ARRANT Y Through S tanton’ s authorized dealers around the W orld, S tanton, or one of S tanton’ s authorized distributo r s outside the U.S., will, without charge, rep air o r replace, at the sole discretion of the entity responsible for making the rep ...

  • Stanton DJLab.3 - page 11

    ST ANTON W ARRANTY REGISTRA TION CARD PERSONAL INFO PRODUCT INFO Name Address City State Zip Country T elephone Model Number Serial Number Date of Purchase Where did you buy this product? If you have internet access, please register your product at www .stantondj.com. Otherwise, return this card completely filled out in order to validate your warra ...

  • Stanton DJLab.3 - page 12

    PLACE ST AMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A. ...

Manufacturer Stanton Category DJ Equipment

Documents that we receive from a manufacturer of a Stanton DJLab.3 can be divided into several groups. They are, among others:
- Stanton technical drawings
- DJLab.3 manuals
- Stanton product data sheets
- information booklets
- or energy labels Stanton DJLab.3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanton DJLab.3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanton DJLab.3, service manual, brief instructions and user manuals Stanton DJLab.3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanton DJLab.3.

Similar manuals

A complete manual for the device Stanton DJLab.3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanton DJLab.3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanton DJLab.3.

A complete Stanton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanton DJLab.3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanton DJLab.3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanton DJLab.3, that we can find in the current document
3. Tips how to use the basic functions of the device Stanton DJLab.3 - which should help us in our first steps of using Stanton DJLab.3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanton DJLab.3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanton DJLab.3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanton DJLab.3?

Use the form below

If you did not solve your problem by using a manual Stanton DJLab.3, ask a question using the form below. If a user had a similar problem with Stanton DJLab.3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)