-
Omnitron Systems Technology 10/100M - page 1
iConverter ® 10/100M Media Converter and Network Interface Device ST ANDALONE AND PLUG-IN MODULE USER MANUAL Release 3.4 ...
-
Omnitron Systems Technology 10/100M - page 2
Page 2 T able of Contents 1.0 Overview .................................................................................................................... 3 1.1 General Description .................................................................................................... 3 1.1.1 Advanced Features ......................................... ...
-
Omnitron Systems Technology 10/100M - page 3
1.0 OVERVIEW This document describes the installation and configuration of the iConverter 10/100M standalone Network Interface Device and plug-in modules. The dif ference between the module types are indicated using the following legend throughout this User Manual: 1.1 GENERAL DESCRIPTION The Omnitron iConverter ® 10/100M is a carrier -class media ...
-
Omnitron Systems Technology 10/100M - page 4
2.0 PORT STRUCTURE 2.1 OVERVIEW The front panel of the 10/100M provides access to the management (serial console), UTP and fiber ports. The fiber port will vary depending on the connector type; ST , SC, MT -RJ, LC or SFP supporting 100BASE-FX transceivers. The plug-in module features two additional Ethernet ports for connectivity via the chassis ba ...
-
Omnitron Systems Technology 10/100M - page 5
19-Module Chassis 5-Module Chassis 2-Module Chassis 1-Module Redundant Chassis 3.0 INST ALLA TION PROCEDURE 3.1 OVERVIEW The following steps outline the installation and configuration procedures for the 10/100M. Refer to the specified sections for detailed instructions. • Configure DIP-switches (Section 3.2) • Installing the Module and Connecti ...
-
Omnitron Systems Technology 10/100M - page 6
3.2 CONFIGURING DIP-SWITCHES The 10/100M plug-in module has two board-mounted DIP-switches. The standalone unit has one bank of DIP-switches. The locations of the DIP-switches are illustrated below . DIP-switch Locations 3.2.1 Board-Mounted Bank 1 Settings DIP-switch Bank 1 is available on both the plug-in and standalone modules. The table indicate ...
-
Omnitron Systems Technology 10/100M - page 7
the “Off” position (factory default) forces the port to negotiate to No Pause mode with its link partner . Setting the Pause DIP-switch to the “On” position allows the port to negotiate to Symmetrical Pause, or No Pause mode with its link partner . When a port is operating in Manual mode, its Pause operation mode is based on the Pause Disab ...
-
Omnitron Systems Technology 10/100M - page 8
100Mbps “100” p osition (factory default) forces the UTP port to operate at 100Mbps. Setting this DIP-switch to UTP 10Mbps “10” position forces the UTP port to operate at 10Mbps. Adjust the “10/100” DIP-switch to match the speed of the connecting UTP device . When the UTP “AN/Man” DIP-switch is in the auto-negotiate “AN” positio ...
-
Omnitron Systems Technology 10/100M - page 9
3.2.2 Board-Mounted Bank 2 Settings DIP-switch Bank 2 is only available on the plug-in module. S w itc h Le ft (Fa c to ry D e fau lt) R ig h t SW1 A - D S: Backp lan e P o rt A Di sa bled A -EN: Por t A En abl ed SW 2 B- DS: Backp lan e P o rt B D i sa bled B- EN: Por t B En abl ed SW3 Re served Reserved SW 4 M/ SL: Ma s t e r /S la ve A uto- S e ...
-
Omnitron Systems Technology 10/100M - page 10
3.3 INST ALLING PLUG-IN MODULES AND CONNECTING CABLES a. Carefully slide the module into an open slot in the chassis. Align the module with the installation guides and ensure that the module is firmly seated against the backplane. Secure the module by fastening the front panel thumbscrew (push in and turn clockwise to tighten) to the chassis front. ...
-
Omnitron Systems Technology 10/100M - page 11
3.4 CONFIGURE THE MODULE VIA COMMAND LINE INTERF ACE T o configure, attach the 10/100M to a DB-9 serial (RS-232) equipped computer with terminal emulation software such as HyperT erminal. The 10/100M Serial Console Port (DCE) is a mini DIN-6 female connector which can be changed to a DB-9 connector with the included adapter (Part #8082-0). Attach t ...
-
Omnitron Systems Technology 10/100M - page 12
The Management Options screen will be displayed. Management Options iConverter, Serial Agent Network Management 1: Chassis and Module Management 2: Set Module Identifier Management Module Preferences 3: IP and Control Preferences 4: SNMP Preferences 5: Abandon Preference Changes 6: Save Preference Changes 7: Restore to Factory Defaults 8: Restart M ...
-
Omnitron Systems Technology 10/100M - page 13
3.4.1 Setting IP and Control Preferences An IP address is required for the SNMP manager to address the 10/100M. The factory default setting is 192.168.1.220. The IP address can be configured manually or automatically as a DHCP client. 3.4.1.1 Setting IP Parameters Manually T o manually configure the IP address and control parameters, select 3 from ...
-
Omnitron Systems Technology 10/100M - page 14
Management Options iConverter, Serial Agent Network Management 1: Chassis and Module Management 2: Set Module Identifier Management Module Preferences 3: IP and Control Preferences 4: SNMP Preferences 5: Abandon Preference Changes 6: Save Preference Changes 7: Restore to Factory Defaults 8: Restart Management Module 9: Other Networking Features Man ...
-
Omnitron Systems Technology 10/100M - page 15
Page 15 NOTE: When the NMM is installed into the chassis and is set to Remote OAM, the chassis number of the 10/100M is automatically assigned by the NMM. IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 1 ...
-
Omnitron Systems Technology 10/100M - page 16
IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 10/100M 6: Enable/Disable TELNET Enabled 7: Enable/Disable FTP Disabled 8: Enable/Disable Soft Switch Reload Disabled 9: TELNET Password ***** 10: FTP Passw ...
-
Omnitron Systems Technology 10/100M - page 17
SNMP Preferences Screen iConverter, Serial Agent Chassis Number = 1 SNMP Engine ID 80001CAE03000687003B19 1: sysContact Omnitron (949) 250-6510 2: sysLocation Irvine, CA USA 3: SNMP Writes Enabled SNMP v1/v2c ------------------------------------------------------------------- 4: Read Community ***** 5: Write Community ***** 6: Agent Enabled SNMP V3 ...
-
Omnitron Systems Technology 10/100M - page 18
authNoPriv provides authentication based on the HMAC-MD5 algorithm and authPriv provides DES 56-bit encryption based on the HMAC-MD5 algorithm. T o set User 1 security , select 10 at the SNMP Preferences screen, press < ENTER > and then follow the screen prompts. T o set the User 2 security , select 13 at the SNMP Preferences screen, press &l ...
-
Omnitron Systems Technology 10/100M - page 19
Page 19 3.4.3 Management Processor VLAN Support The 10/100M Management Processor can independently transmit and receive Management Data with an IEEE 802.1Q tag. T o enable and configure this feature, type 9 from the Management Options screen to access the Other Networking Features screen. Management Options iConverter, Serial Agent Network Manageme ...
-
Omnitron Systems Technology 10/100M - page 20
(non-management modules) are determined by their hardware DIP-switch settings following a return of power . When the Soft-switch Reload is enabled, the configurations of the 10/100M and the other managed modules are determined by the previous software settings stored in the FLASH memory of the 10/100M following a return of power . Each of the hardw ...
-
Omnitron Systems Technology 10/100M - page 21
Page 21 3.4.5 Access the 10/100M Remotely Remote access to the 10/100M is provided via SNMP , T elnet, FTP or an external serial modem connected to the Serial Console Port. 3.4.5.1 Accessing the 10/100M via NetOutlook (SNMP) The 10/100M module can be remotely accessed by SNMP-client software such as NetOutlook or third- party SNMP management softwa ...
-
Omnitron Systems Technology 10/100M - page 22
IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 10/100M 6: Enable/Disable TELNET Enabled 7: Enable/Disable FTP Disabled 8: Enable/Disable Soft Switch Reload Disabled 9: TELNET Password ***** 10: FTP Passw ...
-
Omnitron Systems Technology 10/100M - page 23
When the upload is complete, the 10/100M displays the update status and then automatically restarts with the newly loaded firmware. 3.4.5.4 Up dating the 10/100M Firmware via FTP Using an FTP application, upload the new firmware into the FTP root directory of the 10/100M. When the file transfer is complete, the 10/100M verifies the file and then au ...
-
Omnitron Systems Technology 10/100M - page 24
4.0 DET AILED MODULE CONFIGURA TION 4.1 OVERVIEW The 10/100M has module parameters that require configuration depending on the application. The Module configuration screen is accessible by selecting the module slot number from the Chassis V iew screen. T o access the Module configuration menu, select 1 at the Management Options screen, press < E ...
-
Omnitron Systems Technology 10/100M - page 25
Chassis View 19 Slot iConverter, Serial Agent Chassis Number = 1 Slot Model Type | Slot Model Type 1 8000-0 NMM | 16 N/A 2 8903-1 10/100M | 17 N/A 3 8911-1 10/100M | 18 N/A 4 N / A | 1 9 N / A 5 8919-0 10/100M | 20 N/A 6 N/A | 21 8200-9 Power Supply 7 N / A | 2 2 N / A 8 N / A | 9 N / A | 10 N/A | 11 N/A | 12 N/A | 13 N/A | 14 N/A | 15 N/A | Module ...
-
Omnitron Systems Technology 10/100M - page 26
Module - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON Condition OFF Condition H/W Actual Slot Number = 1 1: Pause Enabled Pause Disabled Off Off Model Number = 8919-0 2: Fiber HDX Fiber FDX Off Off 3: UTP Manual UTP Auto-Neg Off Off Serial Number = xxxxxxxx 4: UTP 10 Mbps UTP 100 Mbps Off Off Manufacturing D ...
-
Omnitron Systems Technology 10/100M - page 27
4.2 MODULE MANAGEMENT MODE From the Module configuration screen, the management mode can be changed. Select option 18 to change the mode. The management mode options will be displayed. Module - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON Condition OFF Condition H/W Actual Slot Number = 1 1: Pause Enabled Pa ...
-
Omnitron Systems Technology 10/100M - page 28
4.3 PORT CONFIGURA TION The Port configuration screen provides access to the port level configuration parameters, such as, Port Access, Bandwidth Control, SFP information, 802.3ah, Port VLANs, T agged VLANs and cNode Loopback. T o access the Port configuration screen, select C from the Module configuration screen and press <ENTER>. The Port c ...
-
Omnitron Systems Technology 10/100M - page 29
4.3.1 Port Access The Port Access option allows the ports to be disabled/enabled while maintaining the port configuration and network link T o configure Port Access, select option 1 for the Fiber port and option 2 for the UTP port from the Port configuration screen. 4.3.2 Bandwidth Control The 10/100M Bandwidth Control is accessed by selecting opti ...
-
Omnitron Systems Technology 10/100M - page 30
4.3.3 SFP Information The 10/100M module installed with an SFP will provide general and specific information on the SFP . This information is best viewed with SNMP management software. The following is the information available: 4.3.3.1 SFP A0 Information Display This section displays fixed SFP Module information for the following areas. • Identi ...
-
Omnitron Systems Technology 10/100M - page 31
SFP information can be obtained by selecting option 9 from the Port configuration screen. SFP Information - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8919-0 Port = 1 Address A0 Page Contents =================================================== 00: 03 04 07 00 10 02 00 00 00 00 00 01 03 ...
-
Omnitron Systems Technology 10/100M - page 32
4.3.4 802.3ah Parameters The 802.3ah parameters can be monitored and/or configured in the 802.3ah Control screen. • 802.3ah OAM State - The 802.3ah OAM State turns 802.3ah processing on or of f for the selected port. When the port is configured as “Disabled” it will not respond to OAMPDUs (OAM Protocol Data Units). They will be dropped by the ...
-
Omnitron Systems Technology 10/100M - page 33
• Multiplexer State - Indicates the Multiplexer state (“Discard”, “Forward” or “Unknown”) of the remote ports. If “Forward” is displayed, the remote partner is forwarding non-OAMPDUs to the lower sublayer . If “Discard”, the remote partner is discarding non-OAMPDUs network frames. If “Unknown”, the Multiplexer state of the ...
-
Omnitron Systems Technology 10/100M - page 34
4.3.5 802.3ah Event s 802.3ah events can be accessed by selecting options 8 from the Port configuration screen. 802.3ah Event - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8919-0 Port 1 1: Symbol Period Window 0 second < 0 symbols> 2: Symbol Period Threshold 0 symbols 3: Frame Win ...
-
Omnitron Systems Technology 10/100M - page 35
4.3.6 Port VLAN The flow of data on the module is controlled by configuring the Port VLAN settings. The block diagram illustrates the flow of both the management traffic and the data traf fic for a plug-in module (standalone modules do not have backplane access). The data traf fic is controlled by a switch matrix which provides complete control of ...
-
Omnitron Systems Technology 10/100M - page 36
Port VLAN is access by selecting options 1 1 - 20 or 1 1 - 13 depending on the module type; plug-in or standalone. Module - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Port VLAN Path Setup Slot Number = 11 ---------------------------------- Model Number = 8919-0 11: Fiber to UTP Enable On 12: Fiber to BP A Enable On ...
-
Omnitron Systems Technology 10/100M - page 37
4.3.7 T agged VLAN The 10/100M supports the IEEE 802.1Q tag VLAN packet tagging and un-tagging and the 802.1p Quality of Service priority standards. The following parameters are configured for each port: 4.3.7.1 Port Priority (PRI) This (IEEE 802.1p based) user-specified value of 0 through 7 can be assigned as a QoS priority level (0 being lowest a ...
-
Omnitron Systems Technology 10/100M - page 38
T agged VLAN is accessed by selecting option 4 from the Port configuration screen. The T ag VLAN Control screen will be displayed. Tag VLAN Control - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8919-0 Fiber 1: Port Priority (PRI) 0 BP B 16: Port Priority (PRI) 0 2: PVID (Port VLAN ID 2 ...
-
Omnitron Systems Technology 10/100M - page 39
4.3.8 VLAN Membership T able The VLAN Membership T able lists the permitted VLAN ID (VID) for each egress port on the module. Only packets that are assigned a VID value that matches one of the egress port’ s VID memberships are allowed to egress through the port. When the Ingress Security is set to High for a specific port, the membership table i ...
-
Omnitron Systems Technology 10/100M - page 40
Initially the table is empty . T o configure the ports with VLAN IDs, select option (a) from the VLAN Membership configuration screen. Membership Entry - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8919-0 VLAN Table Membership Entry 1 ------------------------------ 1: VLAN ID 2 2: Fiber ...
-
Omnitron Systems Technology 10/100M - page 41
T o add a VLAN ID to the membership table, select option 1 and enter the ID #. T o associate the VLAN ID to a port, select the appropriate port option ( 2 - 6 or 2 - 4 ) depending on the module type; plug-in or standalone. Membership Entry - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8 ...
-
Omnitron Systems Technology 10/100M - page 42
Once all the VLAN IDs have been assigned, select option 7 or 5 to save the entries. VLAN Membership - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8919-0 VLAN ID (VID) Fiber UTP BP A BP B Mngmnt 1: 100 Yes No No No No Add new entry (a), Delete entry (d), Edit entry (e), Clear table (c) E ...
-
Omnitron Systems Technology 10/100M - page 43
4.3.10 Port St atistics The 10/100M module provides port statistics on both the fiber and UTP port. The Port Statistics can be viewed by selecting option P from the Module configuration screen. Module - iConverter 10/100M iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON Condition OFF Condition H/W Actual Slot Number = 1 1: Pause E ...
-
Omnitron Systems Technology 10/100M - page 44
5.0 10/100M SPECIFICA TIONS Plug-i n Module Standalone T ablet op S tandalone W al l-M oun t Descri pt ion 10/100BA S E -T X UT P to 100B A S E -FX F i b er Medi a C onv erter w i th i n tegrated man ag emen t Protocol s 10BAS E-T , 100BASE-T X,1 00BA SE-FX w i th 1536 by te s max . fr ame si z e Cabl e T ypes U T P EI A/T I A 568A/ B, C ateg ory 5 ...
-
Omnitron Systems Technology 10/100M - page 45
6.0 TROUBLESHOOTING GUIDE 6.1 OVERVIEW The 10/100M module has several LED indicators available to assist in the determination of problems. Refer to Section 3.5, V erify Operation, for LED definitions. 6.1.1 Power Issues Problem: The Power LED does not illuminate after installation is complete or no LED indicators ar e ON Possible Causes: A. For sta ...
-
Omnitron Systems Technology 10/100M - page 46
Possible Causes: A. Confirm that the UTP cable is connected properly to the iConverter 10/100M and the attached UTP device. Once a connection has been established between the iConverter and its link partner (switch or workstation), the UTP “10/100” LED should illuminate. If the LED does not illuminate, check the Link Mode configuration. A link ...
-
Omnitron Systems Technology 10/100M - page 47
7. 0 WARRANTY This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. T O REGISTER, COMPLETE AND MAIL OR F AX T ...
Do you have a question concerning Omnitron Systems Technology 10/100M?
Use the form below
If you did not solve your problem by using a manual Omnitron Systems Technology 10/100M, ask a question using the form below. If a user had a similar problem with Omnitron Systems Technology 10/100M it is likely that he will want to share the way to solve it.