English dropdown-ico

Manual Craftsman 917.27603

64 pages 2.5 mb
Download

Go to site of 64

Summary
  • Craftsman 917.27603 - page 1

    Owner's Manual J CRIIFTSMIIM" J ii GARDEN TRACTOR 25.0 HP, 50" Mower Electric Start 6 Speed Model No. 917.276030 _] This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual. IMPORTANT: Read and follow all Safety Rules and ...

  • Craftsman 917.27603 - page 2

    Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 6 Assem bly/Pre-Operation ....................... 8 Operation ............................................. 12 Maintenance Schedule ........................ 18 Maintenance ......... ...

  • Craftsman 917.27603 - page 3

    IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death, WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire wh ...

  • Craftsman 917.27603 - page 4

    DO: • Mow up and down slopes, net across, • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Un- even terrain could overturn the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Follow the manufacturer's reco ...

  • Craftsman 917.27603 - page 5

    • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing. • Never carry children. They may fall off and be seriously injured or i ...

  • Craftsman 917.27603 - page 6

    PRODUCT SPECIFICATIONS Gasoline 5 Gallons Capacity Unleaded and Type: Regular Oil Type SAE 10W30 (above 32°F) (API-SF-SJ): SAE 5W-30 (below 32°F) Oil Capacity: W/Filter: 4.0 Pints W/O Filter: 3.5 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed Lo: Hi: (MPH): 0.7 1.7 1.4 3.3 2.3 5.4 Reverse: 0.9 2.1 Tire Pressure: Front: 14 PSI Re ...

  • Craftsman 917.27603 - page 7

    Steering Wheel Insert Steering Sleeve Extension I Mower Leveling Wrench Bubble (2) Flanged _ Mower (1)Front Plate _- Assembly _iv'q_l_ Seat (1) Washer 17/32 x 1-3/16 x 12 Gauge _(t) Knob (5) Retainer Springs loop) ) etainer Springs (single loop) I (4) Brackets Gauge Wheels (4) Retainer Springs _(4) Wheels ( (Opti°nal) t _ _--- (12) Crownlock ...

  • Craftsman 917.27603 - page 8

    Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin. TO ...

  • Craftsman 917.27603 - page 9

    INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. 3. Place seat on seat pan so head of shoulder bolts are position ...

  • Craftsman 917.27603 - page 10

    INSTALL MOWER AND DRIVE BELT Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake. 1. Cut and remove ties securing anti- sway bar and belts, Swing anti-sway bar to left side of mower deck. 2. Slide mower under tractor with de- flector shield to right side of tractor. IMPORTANT: ...

  • Craftsman 917.27603 - page 11

    CHECKTIRE PRESSURE The tires on your tractor were overin- flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual. CHECK MOWER LEVELNESS For best cutting results, mower should be properly leveled. ...

  • Craftsman 917.27603 - page 12

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I',,I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION ENGINE OFF LIGHTS ON ENGINE ON ENG|NE START PARKtNG BRAKE PARKtNG BRAKE PARKtNG BRAKE LOCKED UNLOCKED OVER TEI_P FUEL OiL PRESSURE BA'I'rERY REVERSE F ...

  • Craftsman 917.27603 - page 13

    KNOW YOUR TRACTOR READTHIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference, Ammeter Ignition Switch Position Throttle Control Clutch Switch Lift Lever Plunger Clutch/Bra ...

  • Craftsman 917.27603 - page 14

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR TO SE ...

  • Craftsman 917.27603 - page 15

    The cutting height range is approximately 1-1/2" to 4o1/2". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 inches dur ...

  • Craftsman 917.27603 - page 16

    TO TRANSPORT • Raise attachment lift to highest position with attachment lift control. • When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position. • Do not push or tow tractor at more than five (5) MPH. NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is clos ...

  • Craftsman 917.27603 - page 17

    • The attachments and ground drive can f now be used. If the engine does not accept the load, restart the engine and / allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING (50 ° F and below) 7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the ch ...

  • Craftsman 917.27603 - page 18

    DATES Check. Operator presence and T I.tef_< Systems R che_ for Lo06e Fasteners _ _1_,, A Sha_oeNReplace Mower Blades ll_h_ C Lubr_cati°n Chart I_ 0 i Chock Battery Lovel R J Clean Sa ftety and TG mlif_l_l_ Chock Transaxle Cooling 11_ Chock V-Bel_ Check Engine Oi] Lever _ V' Change Engir_e Oil (with oil fitter) _._ I_ E : Change En_ne Oil ...

  • Craftsman 917.27603 - page 19

    TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires ( ...

  • Craftsman 917.27603 - page 20

    • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for I hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BAI-FERY AND TERMIN ...

  • Craftsman 917.27603 - page 21

    ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR RLTER Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or eve ...

  • Craftsman 917.27603 - page 22

    WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER- VICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key to "STOP" and remove key, 5. Make sure the blades and all moving ...

  • Craftsman 917.27603 - page 23

    • If adjustment is necessary, under left hand footrest, turn lift link adjustment nut (above yellow cap) in appropriate direction to bring bubble between the lines in the bubble level. • Remove bubble level from mower and store in a safe place. Bubble Between Bubble Level Lines Level Decal pBerake_ Left Hand o _--_____. Lift Link ,_ L-__ _Adjus ...

  • Craftsman 917.27603 - page 24

    TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL 1. Park tractor on a level surface. Engage parking brake, 2. Remove screws from L.H. mandrel cover and remove cover, 3. Roll belt over the top of LH. mandrel pulley. 4. Remove belt from electric clutch pulley. 5. Remove belt from idler pulleys. 6. Remove any dirt or grass c_ippings which may have ...

  • Craftsman 917.27603 - page 25

    TO REPLACE MOWER BLADE DRIVE BELT Park the tractor on level surface. Engage parking brake. 1. Remove mower drive belt (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual). 2. Remove mower (See "TO REMOVE MOWER" in this section of this man- ual). 3. Remove screws from R.H. mandrel cover and remove cover. Unhook spri ...

  • Craftsman 917.27603 - page 26

    , Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is neces- sary. Replace brake pads or contact a Sears or other qualified service center. IMPORTANT: Check Brake Adjustment. Clutching Clutching Idler Above Engine Belt ...

  • Craftsman 917.27603 - page 27

    Adjustment Sleeves Jam Nuts TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL - 1. Block up axle securely. 2. Remove axle cover, retaining ring and washers to allow wheel removal, 3. Repair tire and reassemble, 4. Replace washers and snap retaining ring securely in axle groove. 5. Replace axle cover. REAR WHEEL - 1. Block rear axle securely. 2, Remove five ( ...

  • Craftsman 917.27603 - page 28

    Terminal,--:' ._ _;i_;_>_l_" Hex Access :: _ _ Bolt Door ,---_"_ ['4_#;_g A _w'lr(_ Positive (Fled) Cable Terminal _ I P Guard _ _ _'Negative (Black) _,_'J P" Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push ...

  • Craftsman 917.27603 - page 29

    TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be nec- essary, check adjustment as described be- low before loosening cable. If adjustment is necessary, proceed as follows: 1. With engine not running, move choke control (located on dash panel) to full choke position. 2. Remove air cleaner cover, f ...

  • Craftsman 917.27603 - page 30

    Immediately prepare your tractorfor stor- age at the end of the season or if the trac- _will not be usedfor 30 days or more. WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tractor for winter ...

  • Craftsman 917.27603 - page 31

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start 1, 2. 3, 4. 5. 6. 7 Hard to start Engine will not turn over Engine clicks but will not start CAUSE Out of fuel. Engine not "CHOKED" properly. Engine flooded, 3. Bad spark plug. 4. Dirty air filter. 5. Dirty fuel filter. ...

  • Craftsman 917.27603 - page 32

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION LOSS of power Excessive vibration Engine continues to run when operator leaves seat with with attachment clutch engaged 1. Cutting too much grass/too fast. 2. Throttle in "CHOKE" position. 3, Build-up of grass, leaves ...

  • Craftsman 917.27603 - page 33

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service centel PROBLEM Mower blades will not rotate Poor grass discharge CAUSE 1. Obstruction in clutch mechanism. 2. Worn/damaged mower drive belt. 3. Frozen idler pulley. 4. Frozen blade mandrel. 1. Engine speed too slow. 2. Travel speed too fast. 3. Wet grass. 4. M ...

  • Craftsman 917.27603 - page 34

    NOTES 34 ...

  • Craftsman 917.27603 - page 35

    SCHEMATIC TRACTOR -- MODEL NUMBER 917.276030 '° ;1_1_1_ - BATTERY IGNITION SWITCH POSI_O_t CIRCUIT "MAKE" OFF M+G+A1 NONE ON + LIC_ B+A1 L÷A2 ON B + A1 NONE START B+S÷A1 NONE WIRING INSULATED CUPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERViCiNG OF UNIT. THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING I I CLUTCH ! ...

  • Craftsman 917.27603 - page 36

    TRACTOR - - MODEL NUMBER 917.276030 ELECTRICAL 12 22 I I I I I i I I 1 I I I / 26 I I l I I I I 33 36 ...

  • Craftsman 917.27603 - page 37

    ELECTRICAL TRACTOR - - MODEL NUMBER 917.276030 KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt 1/4-20 x 7.5 Zinc 11 150109 Hold down Battery Dash Mount 12 145769 Nut Push Nylon 1/4" 16 176138 Switch Interlock Push-In 21 175688 Harness Socket Light W/4152J 22 41523 Bulb Li ...

  • Craftsman 917.27603 - page 38

    TRACTOR - - MODEL NUMBER 917.276030 CHASSIS AND ENCLOSURES _0 19 17 16 i 63 17 38 ...

  • Craftsman 917.27603 - page 39

    TRACTOR - - MODEL NUMBER 917.276030 CHASSIS AND ENCLOSURES KEY PART NO. NO. 1 2 4 5 6 7 8 14 16 17 18 19 2O 21 24 28 30 31 32 33 34 35 36 37 39 175278 43 136939 44 136940 45 154913 50 175476 56 154914 58 193569 60 17000616 63 19131614 KEY PART DESCRIPTION NO. NO. 180374 Rail, Frame RH 66 17490606 175282 Drawbar, Gt 67 156973 73680700 Nut, Crownlock ...

  • Craftsman 917.27603 - page 40

    TRACTOR -- MODEL NUMBER 917.276030 GROUND DRIVE 29 6 36 47 4O ...

  • Craftsman 917.27603 - page 41

    TRACTOR - - MODEL NUMBER 917.276030 GROUND DRIVE KEY PART KEY PART NO, NO, DESCRIPTION NO. NO. DESCRIPTION 3 7563R Washer, Thrust, Axle 39 74321016 4 17490508 Screw Thdrol 5/16-18 x 3/4 40 178575 5 STD541437 Nut, Crownlock 3,'8-16 41 73931000 6 STD561210 Pin, Cotter 42 8883R 7 149176 Wheel, Hub Assembly 46 145170 8 12000034 Klip. Ring 47 13822 ...

  • Craftsman 917.27603 - page 42

    TRACTOR - - MODEL NUMBER 917.276030 STEERING ASSEMBLY LIp ...

  • Craftsman 917.27603 - page 43

    TRACTOR - - MODEL NUMBER 917.276030 STEERING ASSEMBLY KEY PART NO. NO. 1 159944X428 2 178557 3 6855M 4 161849 5 161848 6 6266H 7 121748X 8 12000029 9 184946X505 10 74781044 11 136518 12 73901000 13 121749X 14 STD551137 15 STD541537 16 145103 17 137347 18 175572 19 156011 20 163887X428 21 159945 22 155105 23 152927 25 STD523710 26 159946X428 27 3366 ...

  • Craftsman 917.27603 - page 44

    ENGINE TRACTOR - - MODEL NUMBER 917.276030 21 _ 20 18 28 39 r 81 69 62 i 4O 85 29 SPARK ARRESTER KIT I 44 ...

  • Craftsman 917.27603 - page 45

    ENGINE TRACTOR - - MODEL NUMBER 917.276030 KEY PART NO. NO. 1 ...... 2 149723 8 121361X 9 177748 10 175287 11 170056 12 143996 15 179115 18 179124X428 20 177328X426 21 171875 22 175441)(428 24 STD551237 25 73920600 26 3645J 27 139277 28 7834R 29 137180 35 10010500 37 123487X DESCRIPTION KEY PART NO. NO. DESCRIPTION Engine (See Breakdown) Kohler 39 ...

  • Craftsman 917.27603 - page 46

    TRACTOR - - MODEL NUMBER 917.276030 SEAT ASSEM BLY 21 I _38_ KEY PART NO. NO. DESCRIPTION 1 180598 Seat 2 180166 Bracket, Pivot Seat 5 145006 Clip, Push In. Hinged 6 STD541437 Nut. Crownlock 3/8-16 Unc 7 124181X Spring, Seat Cprsn 8 171877 Solt 5/16-18Unex 3/4 w/Serns 10 180186 Pan, Seat 12 121246)( Bracket, Mounting Switch 13 121248X Bushing, Snap ...

  • Craftsman 917.27603 - page 47

    DECALS TRACTOR - - MODEL NUMBER 917.276030 6 5 5_, 4 1o 19 17 24 12 -- 23 8 22 KEY PART NO, NO. 1 177665 2 164085 3 186242 4 186243 5 186725 6 133644 B 185980 9 186572 10 156439 11 181249 12 146047 14 160397 15 186401 17 149516 25 14 2O KEY PART DESCRIPTION NO. NO. Decal, Dash Panel, Lower 18 164065 Decal, Dash 19 138047 Decal, Hood, RH 20 181470 D ...

  • Craftsman 917.27603 - page 48

    TRACTOR - - MODEL NUMBER 917.276030 LIFT ASSEMBLY 4O 42 43 38 35 73 34 29 31 3 1 ...

  • Craftsman 917.27603 - page 49

    TRACTOR - - MODEL NUMBER 917.276030 LIFT ASSEMBLY KEY PART NO. NO, DESCRIPTION 1 121006X Rod Asm., Lever 2 180045 Shaft Asm., Lift Vgt 3 159189 Lever Asm., Lift Rh 4 12000022 E-Ring Truarc #5133-87 5 19292016 Washer 29/32 x 1-1/4 x 16 Ga. 6 71110624 Bolt, Fin Hex 3/8-16 unc x1-1/2 7 175830 Grip, Handle Fluted 8 175831X506 Button. Plunger 10 183894 ...

  • Craftsman 917.27603 - page 50

    TRACTOR -- MODEL NUMBER 917.276030 MOWER DECK 30 6 54 8_ 3O 47 48 17,_ 1123 21 22 ...

  • Craftsman 917.27603 - page 51

    TRACTOR - - MODEL NUMBER 917.276030 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 181606 Mower Deck Weldment 50 42 STD633107 2 STD541413 Nut. Crowrdock 5/16-18 43 136469 5 138457 Bracket Asm., Sway Bar 44 165723 6 STD624008 Retainer. Spring 45 s'rD541437 7 178024 Bar, Sway Deck 46 74760628 8 850857 Bolt 3/8-24 x 1.25 Gr. 8 47 1372 ...

  • Craftsman 917.27603 - page 52

    TRANSAXLE TRACTOR - - MODEL NUMBER 917.276030 80 2O 5 4 74 7O 73 72 6 J 2 ,.16 ,15 14 7 41 25 24 ...

  • Craftsman 917.27603 - page 53

    TRANSAXLE TRACTOR -- MODEL NUMBER 917,276030 KEY PART NO. NO. 1 4197R 2 12000034 3 4199R 4 4216R 5 4215R 6 4217R 7 174728 8 74020652 9 7392M 10 137261 11 4985R 12 6266H 13 4212R 14 137125 15 6276H 16 633A63 17 8118M 18 8740H1 19 122238X 20 4218R 21 6252H1 22 781 OH 23 6262H 24 7393R 25 992R1 26 139111 27 4986R 28 122254X 29 6269H 30 5855H 31 174731 ...

  • Craftsman 917.27603 - page 54

    TRACTOR - - MODEL NUMBER 917,276030 KOHLER ENGINE-MODEL NUMBER CV730,TYPE NUMBER 0017 YLINDER HEAD, VALVE AND BREATHER I I a _--- 2t -" CRANKCASE I =-.. /, 3 / Xl X F' vI v I 54 ...

  • Craftsman 917.27603 - page 55

    TRACTOR -- MODEL NUMBER 917.276030 KOHLER ENGINE-MODEL NUMBER CV730,TYPE NUMBER 0017 HEAD/VALVE/BREATHER KEY PART NO. NO. DESCRIPTION 1. 2o 3. 4. 5, 6, 7, 8, 9. 10. 11. 12. 13. 14, 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31, 32. 33. 34. 35. 24.033-03-S 24-041-23-S 24-096-87-S M-645020-S 25 139 60-S 25-3,51-01-S 24-755-66-S 2 ...

  • Craftsman 917.27603 - page 56

    TRACTOR - - MODEL NUMBER 917.276030 KOHLER ENGINE-MODEL NUMBER CV730,TYPE NUMBER 0017 IGNITION/ELECTRICAL I ,_. _z_. BLOWER HOUSING AND BAFFLESJ J AIR INTAKE J 56 ...

  • Craftsman 917.27603 - page 57

    TRACTOR - - MODEL NUMBER 917.276030 KOHLER ENGINE-MODEL NUMB ER CV730, TYPE NUMBER 0017 IGNITION/ELECTRICAL KEY PART NO. NO. DESCRIPTION 25-454-03-S 1, 54-755-15-S Kit, grass screen (Includes 2-4) 2. M-403025-S Screw, hex. cap M4x0.7x25 (4) 3. X-25-92-S Washer. plain 5/16" (4) 4. 24-112-04-S Spacer, grass screen (4) 5, 25-086-47-S Bolt. should ...

  • Craftsman 917.27603 - page 58

    TRACTOR - - MODEL NUMBER 917.27_30 KOHLER ENGINE-MODEL NUMBER CW30,WPE NUMBER _17 STARTING SYSTEM I @ ENGINE CONTROLS 5 4 _8 /27 $ / =,, 'I_,,7 ,, OIL PAN I LUBRICATION I O ! I I _8 4_ .-2 i ".F J,/' 58 ...

  • Craftsman 917.27603 - page 59

    TRACTOR -- MODEL NUMBER 917.276030 KOHLER ENGINE-MODEL NUMBER CV730, TYPE NUMBER 0017 STARTING SYSTEM KEY PART NO. NO. DESCRIPTION 1, 2. 3. 4. 5. 6. 7. M-839080-S 25-098-09-S 25 086 113_S 25-435-05-S 25-755-33-S 25-141-05-S 25-221-01-S Screw, hex. flange MSx1.25x80 (2) Starter, solenoid shift _ncludes 3-7) crew, external torx hd. (3) Kit, solenoid ...

  • Craftsman 917.27603 - page 60

    TRACTOR - - MODEL NUMBER 917,276030 KOHLER ENGINE-MODEL NUMBER CV730,TYPE NUMBER 0017 CRANKSHAFT J 2--1_I FUEL SYSTEM I EXHAUST I ul / 1 , Z 12 13 14 ...

  • Craftsman 917.27603 - page 61

    TRACTOR - - MODEL NUMBER 917.276030 KOHLER ENGINE-MODEL NUMBER CV730,TYPE NUMBER 0017 CRANKSHAFT KEY PART NO. NO. DESCRIPTION 1, 24-014-72-S Crankshaft (Includes 2) 2, 52-139-09-S Plug, cup EXHAUST KEY PART NO. NO. DESCRIPTION 1, 24-041-02-S Gasket, exhaust (2) 2. 25-072-04-S Stud, MBx1.25x33 (4) - - 24 782 23 Miniblock -- 24 755 113-S Gasket Set F ...

  • Craftsman 917.27603 - page 62

    62 ...

  • Craftsman 917.27603 - page 63

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION 0") O3 1. Fold this page along dotted line Indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with th ...

  • Craftsman 917.27603 - page 64

    iiiiiiiii_i_iiiiiiiii _' iiiiiiiiiiiiii :+>:.:.:+:_ :::::::;_::::::: _::<:+:: ::::::+: :_:_:::::::;:: :::::::: ::::_:::;::::::: ii _ii _ Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, a ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 917.27603 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 917.27603 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 917.27603
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 917.27603.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 917.27603, service manual, brief instructions and user manuals Craftsman 917.27603. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 917.27603.

Similar manuals

A complete manual for the device Craftsman 917.27603, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 917.27603 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 917.27603.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 917.27603 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 917.27603, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 917.27603, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 917.27603 - which should help us in our first steps of using Craftsman 917.27603
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 917.27603
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 917.27603 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 917.27603?

Use the form below

If you did not solve your problem by using a manual Craftsman 917.27603, ask a question using the form below. If a user had a similar problem with Craftsman 917.27603 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)