-
Hotpoint WT 400 - page 1
Instructions f or Installation and Use T op Loading W ashing machine Model WT 400 ...
-
Hotpoint WT 400 - page 2
2 GB English W A SHING MACHINE WT 400 Instructions f or use GB Contents Installation, 3-4-5 Unpacking and levelling, 3 Electric and water connections, 3-4 The first wash cycle, 5 T echnical details, 5 W ashing machine description, 6-7 Control panel, 6 How to open and shut the drum, 7 Leds, 7 Starting and Programmes, 8 Briefly: how to start a progra ...
-
Hotpoint WT 400 - page 3
3 Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the f eet in such a way as to allow enough room f or ventilation beneath the washing machine. K eep this instruction manual in a safe place f or f uture ref erence ...
-
Hotpoint WT 400 - page 4
4 GB Connecting the drain hose Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; alternatively , place it over the edge of a basin, sink or tub, f astening the duct supplied to the tap (see figure) . The free end of the hose should not be under wat er . We advise agains ...
-
Hotpoint WT 400 - page 5
5 If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fu se, either in the plug or adaptor or at the distribution board. If you are in any doubt the electrical supply to your machine, consult a qualif ied electrician bef ore use. How to connect an alternative plug: The wires in this mains lead are coloured in accordance with the f ol ...
-
Hotpoint WT 400 - page 6
6 GB W ashing machine description Detergent dispenser: to add detergent and f abric softener (see page 10). LEDS: t o f ind out which wash cycle phase is under way . If the Time Delay f unction has been set, the time left until the programme starts will be indicated (see page 7) . FUNCTION buttons: to select the f unctions available. The button cor ...
-
Hotpoint WT 400 - page 7
7 GB Cycle phase under way: During the wash cycle, the LEDs gradually illumi- nate on to indicate the cycle phase under way: Prewash W a s h Rinse Spin Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding butto ...
-
Hotpoint WT 400 - page 8
8 GB T yp e of f a b r ic and degr ee of soil Progr am - mes Wa s h temp er at. Det ergent Fa bri c s of tener Cy cle length (minutes) De s crip tion of was h cy cle Pre - wa sh Wa s h Co tton s Prew ash- E xt remel y soi l ed white s ( she e t s, ta blecloth s, e tc.) A 90°C 14 0 Pr ew ash , w a s h c y c l e , r i n s e c y c l e s , ...
-
Hotpoint WT 400 - page 9
9 GB F unction Eff ect Comm ents Enab led wit h pr ogr a mmes : Time Del ay Delays the st art of t he w ash by up t o 9 hours. Pr es s the b ut t on repea t edl y unt i l the LE D c or r es pond i ng t o the desi red delay i s turne d on . T he f i fth time the bu t ton is pr esse d, th e f u n ct ion will be dis abled. N . B .: On c e you ha v e p ...
-
Hotpoint WT 400 - page 10
Detergent dispenser Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make f or a more efficient wash, and may in f act cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and f abric softener , ...
-
Hotpoint WT 400 - page 11
Precautions and advice The washing machine was designed and built in compliance with the applicable international saf ety regulations. The f ollowing inf ormation is provided f or your saf ety and should consequently be read carefully . General saf ety This appliance has been designed f or non- prof essional, household use and its f unction ...
-
Hotpoint WT 400 - page 12
12 GB Care and maintenance Cutting off the water or electricity supply T urn off the water tap after ever y wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations. Cleaning your appliance The exterior and rubber parts of your a ...
-
Hotpoint WT 400 - page 13
13 GB Y our washing machine could f ail to work. Bef ore calling f or Assistance (see page 14-16) , make sure the problem can't easily be solved by consulting the f ollowing list. T roubleshooting Problem The washing machine won't start. The wash cycle won't start. The washing machine f ails to load water . The washing machine contin ...
-
Hotpoint WT 400 - page 14
14 GB "No company is better positioned to off er an after sales service on a Hotpoint appliance than us - the manuf acturer" As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee f or the f irst 12 months. In addition to this you also have the advantage of f ree re ...
-
Hotpoint WT 400 - page 15
15 Guarantee "Satisf action guaranteed or your money back" W e give you a unique 'satisf action guaranteed' promise - valid f or 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www .theservic ec entre.c o.uk and where ...
-
Hotpoint WT 400 - page 16
16 GB Over 1200 trained specialists, directly employed by us, ensure that you can have complete conf idence in both the appliances and services we off er . Repair Service and Inf ormation Desk UK: 08709 066 066 (Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays) www .theservic ec entre .c o.uk Republic of Ireland: 1850 302 200 Note ...
Do you have a question concerning Hotpoint WT 400?
Use the form below
If you did not solve your problem by using a manual Hotpoint WT 400, ask a question using the form below. If a user had a similar problem with Hotpoint WT 400 it is likely that he will want to share the way to solve it.