English dropdown-ico

Manual Cisco Systems CATALYST 2940

24 pages 1.97 mb
Download

Go to site of 24

Summary
  • Cisco Systems CATALYST 2940 - page 1

    Getting St arted Guide Catalyst 2940 Switch Getting Started Guide INCLUDING LICENSE AND W ARRANTY 1 About this Guide 2 T aking Out What Y ou Need 3 Running Exp ress Setup 4 Managing the Switc h 5 Installing the Switc h 6 In Case of Difficulty 7 Obtaining Documentation 8 Obtaining T ec hnical Assistance 9 Cisco Limited Lifetime Hardware W arranty T ...

  • Cisco Systems CATALYST 2940 - page 2

    2 1 About this Guide This guide provides instruction s on how to use Ex press Setup to initially config ure your Catalyst switch. Also covered are switch management options, basic installation procedures, port a nd module connections, and troubleshooting help. For additional instal lation and configuration info rmat ion, and technical specification ...

  • Cisco Systems CATALYST 2940 - page 3

    3 Shipping Box Contents Catalyst 2940 switch Three number-8 Phillips pan-head screws Regulatory Compliance and Safety Information for the Catalyst 2940 Switch Catalyst 2940 Switch Getting Started Guide Cisco Product Ownership Registration card Console cable Four rubber mounting feet AC power cord (AC-powered switches only) Screw template Mounting m ...

  • Cisco Systems CATALYST 2940 - page 4

    4 3 Running Express Setup When you first set up the switch, you should use Expr ess Setup to enter the init ial IP information. This enables the switch to connect to local routers and th e Internet. Y ou can then access the switch through the IP address for further configuration. T o run Express Setup: Step 1 V erify that no devices are connected t ...

  • Cisco Systems CATALYST 2940 - page 5

    5 Step 7 Connect a straight-through Category 5 Ethernet cable (not provided) to any 10/100 or 10/100/1000 Ethernet port on the switch front panel and to the Ethernet port on the PC. Step 8 V erify that the LEDs on both Ethernet ports are green. Step 9 W ait 30 seconds. Step 10 Launch a web browser on your PC. Enter the IP address 10.0.0.1 in the we ...

  • Cisco Systems CATALYST 2940 - page 6

    6 Step 12 Enter this information in the Network Settings fields: • In the Management Interface (VLAN ID) field, the default is 1 . Enter a new VLAN ID only if you want to ch ange the management in terface through w hich you manage the switch and to which you assign IP information. The VLAN ID range is 1 to 1001. • In the IP Address field, enter ...

  • Cisco Systems CATALYST 2940 - page 7

    7 Refreshing the PC IP Address After you complete Express Setup, yo u should refresh the PC IP address. For a dynamically assigned IP addr ess, disconnect the PC from the switch, and reconnect it to the network. The network DHCP server will assign a new IP add ress to the PC. For a statically assigned IP address, change it to the previously configu ...

  • Cisco Systems CATALYST 2940 - page 8

    8 Downloading Cisco Network Assistant Cisco Network Assistant is a free software prog ram that you download from Cisco.com and run on your PC. Network Assistant offers advanced options for configuring an d monitoring multiple devices, including switches, switch clusters, switch stacks, routers, and access points. Follow these steps: 1. From the dev ...

  • Cisco Systems CATALYST 2940 - page 9

    9 5 Installing the Switch This section covers switch installation and port co nnections. For additional installation and ca bling information, refer to the Catalyst 2940 Switch Hardware Installation Guide on Cisco.co m. Y ou can order an optional cable guard to secure cables to the front of the switch and prevent them from being accidentally remove ...

  • Cisco Systems CATALYST 2940 - page 10

    10 Installation Warning Statements This section includes the basic installatio n warning statements. War n in g T o prevent the switch from o v erheating, do no t operate it in an area that exceeds the maximum recommended ambient temperature of 113°F (45°C). T o prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the ...

  • Cisco Systems CATALYST 2940 - page 11

    11 Installing the Switch on a Desk or Wall T o place the switch on a desk without using the moun ting screws, simply attach the four rubber feet on the bottom panel of the switch. T o install th e switch on top of a desk, under a desk, or on a wall, use the mounting template and three moun ting screws. Follow these steps: 1. Position the screw temp ...

  • Cisco Systems CATALYST 2940 - page 12

    12 Installing the Switch Using the Magnet Mount Follow these steps: 1. Position the magnetic panel on the mounting surface. 2. Place the bottom of the switch on the magnetic panel. Catalyst 2940 S E R IE S SYST STAT DPLX SPD Metal mounting surf ace Mounting magnet Switch bottom panel ...

  • Cisco Systems CATALYST 2940 - page 13

    13 Connecting to the Switch Ports This section describes how to connect to the fixe d switch po rts and to the SFP module port. For additional cabling information and a list of supporte d SFP modules, refer to the hardware installation guide on Cisco.com. Connect to 10/100 Port s and the 10/100/1000 Port Follow these steps: Connect to t he 100BASE- ...

  • Cisco Systems CATALYST 2940 - page 14

    14 Install and Connect to SFP Module Port Y ou can use either the 100BASE-FX port or the SFP mo dule slot, but not both at the same time. By default, the 100BASE-FX port is active if an S FP modul e is not installed in the switch at startup. If you install an SFP module after th e switch has powered on, you must reload the switch to enable the SFP ...

  • Cisco Systems CATALYST 2940 - page 15

    15 6 In Case of Difficulty If you experience difficulty , help is available here and on Cisco.com. This section includes Express Setup troubleshooting, how to reset the switch, how to access help online, and where to find more information. Troubleshooting Express Setup If Express Setup does not run, or if the Expres s Setup page do es not appear in ...

  • Cisco Systems CATALYST 2940 - page 16

    16 Resetting the Switch This section describes how to reset the switch by rerunning Express Setup. These are reasons why you might want to reset the switch: • Y ou installed the switch in your network and cannot connect to it because you assigned the wrong IP address. • Y ou want to clear all configuration from the switch a nd assign a new IP a ...

  • Cisco Systems CATALYST 2940 - page 17

    17 Follow these steps: 1. Open your browser , and go to http://ww w .cisco.com/. 2. Click T echnical Support . 3. Click Product Support > Switches > Catalyst LAN and A TM Switches > 2940 Series Switches > T roubleshooting . 4. Click the subject that addresses the p roblem that you are experiencing. For More Information For more informat ...

  • Cisco Systems CATALYST 2940 - page 18

    18 7 Obtaining Documentation Cisco documentation and additional literature are ava ilable on Cisco.com. Cisc o also provides several ways to obtain technical assistance and other technical resources. These sections explain how to o btain technical information from Cisco Systems. Cisco.com Y ou can access the most current Ci sco documentation at thi ...

  • Cisco Systems CATALYST 2940 - page 19

    19 Y ou can submit comments by using the response ca rd (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 W est T asman Drive San Jose, CA 95134-9883 W e appreciate your comments. 8 Obtaining Technical Assistance For all customers, partners, resellers, and ...

  • Cisco Systems CATALYST 2940 - page 20

    20 Submitting a Service Request Using the online T AC Service Request T ool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are t hose in which your network is mini mally impaired or for which you require product information.) After you describe your situation, the T AC Service Request T ool provides recommended s ...

  • Cisco Systems CATALYST 2940 - page 21

    21 Obtaining Additional Public ations and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a var iety of Ci sco books, reference gu ides, and logo merchandise. V isit C isco Marketplace, the c ompany store, at this URL: http://www.c ...

  • Cisco Systems CATALYST 2940 - page 22

    22 9 Cisco Limited Lifetime Hardware Warranty Terms There are special terms applicable to your hardware wa rranty and various services that you c an use during the warranty period. Y our formal W arranty Statement, including the warranties and license agreements applicable to Cisco software, i s availabl e on Cisco.com. F ollow these steps to acces ...

  • Cisco Systems CATALYST 2940 - page 23

    23 Duration of Hardware Warranty A Cisco product hardware warranty is supported for as long as the original end user continues to own or use the product, provided that the fan and power su pply warranty is limited to five (5) years. In the event of a discontinuance of product manufa cture, the Cisco warranty support is limited to five (5) years fro ...

  • Cisco Systems CATALYST 2940 - page 24

    Corporate Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Head quarters Cisco Systems Internat ional BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cis co.com T el: 31 0 20 35 7 1000 Fax: 31 0 2 ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems CATALYST 2940 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- CATALYST 2940 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems CATALYST 2940
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems CATALYST 2940.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems CATALYST 2940, service manual, brief instructions and user manuals Cisco Systems CATALYST 2940. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems CATALYST 2940.

Similar manuals

A complete manual for the device Cisco Systems CATALYST 2940, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems CATALYST 2940 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems CATALYST 2940.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems CATALYST 2940 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems CATALYST 2940, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems CATALYST 2940, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems CATALYST 2940 - which should help us in our first steps of using Cisco Systems CATALYST 2940
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems CATALYST 2940
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems CATALYST 2940 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems CATALYST 2940?

Use the form below

If you did not solve your problem by using a manual Cisco Systems CATALYST 2940, ask a question using the form below. If a user had a similar problem with Cisco Systems CATALYST 2940 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)