English dropdown-ico

Manual Bretford LAP24EULBA

33 pages 3.72 mb
Download

Go to site of 33

Summary
  • Bretford LAP24EULBA - page 1

    LAP24EULBA LAP24EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Qt y . Part No. Description 1 LAP24EULBA Cart Assembly , e-units at back LAP24EULFR Cart Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of cart ...

  • Bretford LAP24EULBA - page 2

    clip DET AIL 'A' DET AIL 'B' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford LAP24EULBA - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 14 screws (2 per shelf) from r ...

  • Bretford LAP24EULBA - page 4

    DET AIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford LAP24EULBA - page 5

    Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the rear of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window . 4. Grip the top and tilt to the upright position, underneath top panel bracket. When reposition ...

  • Bretford LAP24EULBA - page 6

    Step 6 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 7 Reinstall 14 scre ...

  • Bretford LAP24EULBA - page 7

    Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AIL 'A'). DET AIL 'A' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'B' mounting tab ...

  • Bretford LAP24EULBA - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the ...

  • Bretford LAP24EULBA - page 9

    DET AIL 'D' DET AIL 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. re ...

  • Bretford LAP24EULBA - page 10

    Step 4 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'F Step 5 Reinstall 14 screws to r ...

  • Bretford LAP24EULBA - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit power switch should ...

  • Bretford LAP24EULBA - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AIL 'A'). DET AIL 'A' DET AIL 'B' mounting tab ...

  • Bretford LAP24EULBA - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip ...

  • Bretford LAP24EULBA - page 14

    DET AIL 'C' DET AIL 'D' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left ...

  • Bretford LAP24EULBA - page 15

    Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window . Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the br ...

  • Bretford LAP24EULBA - page 16

    Step 5 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AIL 'E' Step 6 Reinstall 14 scre ...

  • Bretford LAP24EULBA - page 17

    Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be repl ...

  • Bretford LAP24EULBA - page 18

    clip DET AIL 'A' DET AIL 'B' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. front-right front-left ...

  • Bretford LAP24EULBA - page 19

    front-right front-left Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bra ...

  • Bretford LAP24EULBA - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET AIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab ...

  • Bretford LAP24EULBA - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View). ...

  • Bretford LAP24EULBA - page 22

    Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . The E-Unit bracket assembly shown above, will need to be removed (with a philips screwdriver) to allow the E- Unit to swing back. This will allow the timer cord plug to pass between the E-Unit and rear panel. bottom flange- timer/brack ...

  • Bretford LAP24EULBA - page 23

    Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutout s. Swing the E-Unit back into position and reinstall bracket assembly . Plug in the E-Units power c ...

  • Bretford LAP24EULBA - page 24

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET AIL 'C' Step 8 Reinstall ...

  • Bretford LAP24EULBA - page 25

    SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 E-Unit power cord timer assembly bottom shelf Front View Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefu ...

  • Bretford LAP24EULBA - page 26

    front-right front-left Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET AIL 'A& ...

  • Bretford LAP24EULBA - page 27

    DET AIL 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AIL 'A'). DET AIL 'B' mounting tab ...

  • Bretford LAP24EULBA - page 28

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b ...

  • Bretford LAP24EULBA - page 29

    Step 6 Remove 2 screws that secure timer to bracket. Step 7 Install bracket to replacement timer with 2 nut s. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Timer vents & bracket must be attached as shown. ...

  • Bretford LAP24EULBA - page 30

    Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf wit ...

  • Bretford LAP24EULBA - page 31

    front-right front-left DET AIL 'C' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS. Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top pan ...

  • Bretford LAP24EULBA - page 32

    1 1 2 2 1 1 1 1 1 1 22 15 19 11 7 16 20 8 12 AUX. 1 3 AUX. 2 4 17 21 13 9 18 22 10 14 AUX. 3 1 5 AUX. 4 2 6 23 27 24 28 25 29 26 30 AUX. 5 AUX . 6 LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation of labels peel off and attach corresponding labels to shelves and E-Units. shelf E-Unit E-Unit E-Unit at rear ...

  • Bretford LAP24EULBA - page 33

    Part #031-6566 Rev . 12.22.08 CZ P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert “reset” tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e ...

Manufacturer Bretford Category Computer Accessories

Documents that we receive from a manufacturer of a Bretford LAP24EULBA can be divided into several groups. They are, among others:
- Bretford technical drawings
- LAP24EULBA manuals
- Bretford product data sheets
- information booklets
- or energy labels Bretford LAP24EULBA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bretford LAP24EULBA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bretford LAP24EULBA, service manual, brief instructions and user manuals Bretford LAP24EULBA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bretford LAP24EULBA.

Similar manuals

A complete manual for the device Bretford LAP24EULBA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bretford LAP24EULBA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bretford LAP24EULBA.

A complete Bretford manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bretford LAP24EULBA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bretford LAP24EULBA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bretford LAP24EULBA, that we can find in the current document
3. Tips how to use the basic functions of the device Bretford LAP24EULBA - which should help us in our first steps of using Bretford LAP24EULBA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bretford LAP24EULBA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bretford LAP24EULBA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bretford LAP24EULBA?

Use the form below

If you did not solve your problem by using a manual Bretford LAP24EULBA, ask a question using the form below. If a user had a similar problem with Bretford LAP24EULBA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)