English dropdown-ico

Manual Invacare Top End TerminatorTM SS

60 pages 1.42 mb
Download

Go to site of 60

Summary
  • Invacare Top End TerminatorTM SS - page 1

    Owner's Operator And Maintenance Manual ® Terminator  SS DEALER: THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE. ...

  • Invacare Top End TerminatorTM SS - page 2

    Terminator SS 2 Part No. 1052712 Rev D SPECIAL NOTES WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. As a manufacturer of wheelchairs, Invacare endeavors to supply a ...

  • Invacare Top End TerminatorTM SS - page 3

    Part No. 1052712 Rev D 3 Terminator SS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS SPECIAL NOTES ................................................................................ 2 SPECIFICATIONS .............................................................................. 5 SECTION 1 - GENERA L GUIDELINES ............................. ...

  • Invacare Top End TerminatorTM SS - page 4

    Terminator SS 4 Part No. 1052712 Rev D TABLE OF CONTENTS TABLE OF CONTENTS SECTION 6 - FOOT REST/ANTI-TIPPER ............................................. 46 ADJUSTING/REPLACING STANDARD FOOTREST ...................................................................... 46 INSTALLING/ADJUSTING OPTIONAL CLAMP ON RAISED FOOTREST ...................... ...

  • Invacare Top End TerminatorTM SS - page 5

    Part No. 1052712 Rev D 5 Terminator SS SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. SPECIFICATIONS TERMINATOR SS Frame: Rigid - with Rear Suspension - 4130 Chrome-moly Seat Width: 12-20-inches - Outside to Outside of SEAT FRAME in 1-inch increments. Seat Depth: 14 to 18-inches (15-inch Standard) Seat-to-Floor: Front - ...

  • Invacare Top End TerminatorTM SS - page 6

    Terminator SS 6 Part No. 1052712 Rev D Section 1 - General Guidelines - includes the following: Stability Operating Information Tire Pressure and Information Weight Training Weight Limitation Safety/Handling of Wheelchairs GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES STABILITY STABILITY STABILITY STABILITY STABILITY STABILITY WARNING The posi ...

  • Invacare Top End TerminatorTM SS - page 7

    Part No. 1052712 Rev D 7 Terminator SS WARNING DO NOT tip the wheelchair without assistance. DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur. Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters toward the object you ...

  • Invacare Top End TerminatorTM SS - page 8

    Terminator SS 8 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES TIRE PRESSURE AND INFORMATION WARNING DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm. The recommended tire pressu ...

  • Invacare Top End TerminatorTM SS - page 9

    Part No. 1052712 Rev D 9 Terminator SS SAFETY/HANDLING OF WHEELCHAIRS Safety and Handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair. It is important to pract ...

  • Invacare Top End TerminatorTM SS - page 10

    Terminator SS 10 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES WARNING Do not attempt to lift a wheelchair by lifting on any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair. Also, be aware of any removable (det ...

  • Invacare Top End TerminatorTM SS - page 11

    Part No. 1052712 Rev D 11 Terminator SS Reaching, Leaning and Bending - Forward. Position the front casters so that they are extended as far forward as possible and engage wheel locks. WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees. Reaching, Lean ...

  • Invacare Top End TerminatorTM SS - page 12

    Terminator SS 12 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES TIPPING - CURBS: WARNING Invacare does not recommend that sport wheelchairs be used where traversing curbs present an obstacle. Possible injury to occupant and/or assistant(s) can occur. Transfer to an everyday use wheelchair is recommended if any such obstac ...

  • Invacare Top End TerminatorTM SS - page 13

    Part No. 1052712 Rev D 13 Terminator SS Follow this procedure for moving the wheelchair between floors when an elevator is NOT available: 1. If equipped, turn the anti-tippers UP. Refer to SECTION 6 in this manual. 2. After the wheelchair has been tilted back to the balance point, one assistant (in the rear) backs the wheelchair up against the f ...

  • Invacare Top End TerminatorTM SS - page 14

    Terminator SS 14 Part No. 1052712 Rev D SAFETY INSPECTION SECTION 2 SAFETY INSPECTION Section 2 - Safety Inspection - includes the following: Safety Inspection Checklist Troubleshooting Maintenance NOTE: Every six (6) months, take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loos ...

  • Invacare Top End TerminatorTM SS - page 15

    Part No. 1052712 Rev D 15 Terminator SS TROUBLESHOOTING SAFETY INSPECTION SECTION 2 MAINTENANCE MAINTENANCE SAFETY PRECAUTIONS WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. CAUTION DO NOT overtighten hardware attaching to the frame. ...

  • Invacare Top End TerminatorTM SS - page 16

    Terminator SS 16 Part No. 1052712 Rev D CAUTION As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced if damaged. 5. The wheels, casters and tires should be checked periodically for cracks and wear, and should be replaced when necessary. Contact a qualified technician or Invacare cus ...

  • Invacare Top End TerminatorTM SS - page 17

    Part No. 1052712 Rev D 17 Terminator SS SECTION 3 BACK WARNING ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, camber tube, back angle, the tautness of the back upholstery as well as the user's condition are directly related to the wheelchairs stability. Any change to one (1) or any combination o ...

  • Invacare Top End TerminatorTM SS - page 18

    Terminator SS 18 Part No. 1052712 Rev D BACK SECTION 3 FIGURE 1 - BACK ANGLE ADJUSTMENT BACK 73° BACK ANGLE TO SEAT RAIL 77° BACK ANGLE TO SEAT RAIL 84° BACK ANGLE TO SEAT RAIL 94° BACK ANGLE TO SEAT RAIL 85° BACK ANGLE TO SEAT RAIL 90° BACK ANGLE TO SEAT RAIL Back Cane Indexing Notch Cam Back Angle Bracket Seat Rail TOP Hex Screw and Lock ...

  • Invacare Top End TerminatorTM SS - page 19

    Part No. 1052712 Rev D 19 Terminator SS FOLDING/UNFOLDING THE BACK (FIGURE 2) NOTE: This procedure is for folding back chairs only. WARNING Back MUST be locked securely in place before using the chair. 1. Lift up on the back and pull towards the rear of the chair until it locks into place. 2. To fold the back, pull up on the black nylon cord and ...

  • Invacare Top End TerminatorTM SS - page 20

    Terminator SS 20 Part No. 1052712 Rev D BACK SECTION 3 BACK Replacing Top End Back Upholstery. 1. Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes. 2. Remove the fastening flaps from the back canes by lifting straight up. 3. Remove the seat cushion. 4. Separate the bottom of the back upholstery fro ...

  • Invacare Top End TerminatorTM SS - page 21

    Part No. 1052712 Rev D 21 Terminator SS CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 4) The Adjustable Tension Straps. The straps can be adjusted at various levels of tension to accommodate individual end-users. The bottom two (2) straps can be adjusted tightly to support and/or assist the extensor muscles. The Back Upholstery Cover. ...

  • Invacare Top End TerminatorTM SS - page 22

    Terminator SS 22 Part No. 1052712 Rev D WARNING After the adjustable tension back upholstery has been positioned to the end-users individual needs, the fastening straps MUST be securely fastened BEFORE applying the back upholstery cover. The adjustable back should be checked whenever entering the wheelchair to ensure that the fastening straps ar ...

  • Invacare Top End TerminatorTM SS - page 23

    Part No. 1052712 Rev D 23 Terminator SS BACK HEIGHT ADJUSTMENT (ADJUSTABLE BACKS ONLY) (FIGURE 5 ) NOTE: Observe the tautness of the back upholstery for reinstallation. 1. Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes and remove from the back canes. WARNING Push pin MUST be protruding through ho ...

  • Invacare Top End TerminatorTM SS - page 24

    Terminator SS 24 Part No. 1052712 Rev D SEAT SECTION 4 WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. REPLACING TOP END SEAT UPHOLSTERY (FIGURE 1) WARNING The seat upholstery and/or cushion MUST be cleaned regularly and/or replaced i ...

  • Invacare Top End TerminatorTM SS - page 25

    Part No. 1052712 Rev D 25 Terminator SS REPLACING CUSTOM MANUAL SCREW ON SEAT UPHOLSTERY (FIGURE 2) 1. Remove the seat cushion from the wheelchair. 2. Remove the twelve (12) phillips screws that secure the existing seat upholstery to the seat frame. 3. Remove the existing seat upholstery. FIGURE 2 - REPLACING CUSTOM MANUAL SCREW ON SEAT UPHOLSTE ...

  • Invacare Top End TerminatorTM SS - page 26

    Terminator SS 26 Part No. 1052712 Rev D WHEELS SECTION 5 WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. REMOVING/INSTALLING REAR WHEELS (FIGURE 1) CAUTION Changing the size of the rear wheels can affect the performance of the wheelch ...

  • Invacare Top End TerminatorTM SS - page 27

    Part No. 1052712 Rev D 27 Terminator SS ADJUSTING QUICK-RELEASE AXLES (FIGURE 2) 1. Remove rear wheel and quick-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 2. Depress detent pin in the quick-release axle and slide axle through the wheel hub. 3. Release detent pin ensuring that the loc ...

  • Invacare Top End TerminatorTM SS - page 28

    Terminator SS 28 Part No. 1052712 Rev D INSTALLING QUAD-RELEASE AXLES (FIGURE 3) 1. Remove rear wheel and the existing quick-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 2. Remove existing quick-release axle from rear wheel. 3. Insert new quad-release axle through rear wheel hub. 4. Sl ...

  • Invacare Top End TerminatorTM SS - page 29

    Part No. 1052712 Rev D 29 Terminator SS 4. Tighten the locking screw. 5. Reinstall the rear wheel and quad-release axle onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 6. Flip the handle of the quad-release axle down to release the detent pin ensuring that the locking pins are fully released. 7. Repea ...

  • Invacare Top End TerminatorTM SS - page 30

    Terminator SS 30 Part No. 1052712 Rev D REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE WARNING Replacement of the tire or tube MUST be performed by a qualified technician. CAUTION Changing the size of the rear wheels can affect the performance of the wheelchair. Contact Invacare at the numbers on the back cover BEFORE performing this procedure. NOTE: ...

  • Invacare Top End TerminatorTM SS - page 31

    Part No. 1052712 Rev D 31 Terminator SS WHEELS SECTION 5 RECEIVER TUBE CLAMPS 1. Perform one (1) of the following to open a receiver tube clamp: A. QUICK RELEASE LEVERS - Pull the quick release levers on the receiver tube clamps to the open position. B. STANDARD RECEIVER TUBE CLAMPS - Loosen, but do not remove the hex screws and locknuts on the ...

  • Invacare Top End TerminatorTM SS - page 32

    Terminator SS 32 Part No. 1052712 Rev D ADJUSTING REAR WHEEL CAMBER CAMBER TUBE 2000 The axle tube must be replaced to change the camber. Refer to REPLACING AXLE TUBE in this section of the manual. A4 CAMBER SYSTEM (FIGURE 7) NOTE: Perform this procedure to one (1) side of the wheelchair at a time for ease of adjustment. 1. Open the camber clamp ...

  • Invacare Top End TerminatorTM SS - page 33

    Part No. 1052712 Rev D 33 Terminator SS WHEELS SECTION 5 WHEELS 10. Reinstall rear wheel to the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 11. Adjust toe in/toe out of wheelchair. Refer to ADJUSTING TOE IN/TOE OUT in this section of the manual. DETERMINING TOE IN/TOE OUT (FIGURES 8 AND 9) 1. Inflate all p ...

  • Invacare Top End TerminatorTM SS - page 34

    Terminator SS 34 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS ADJUSTING TOE IN/TOE OUT CAMBER TUBE 2000 (FIGURE 10) 1. Open the camber clamps. Refer to OPENING/CLOSING CLAMPS in this section of the manual. 2. Slowly rotate the camber tube in either direction until the rear wheels are approximately in a straight line. 3. Close the camber clamps ...

  • Invacare Top End TerminatorTM SS - page 35

    Part No. 1052712 Rev D 35 Terminator SS Axle Tube - Rotates Up and Down FIGURE 11 - ADJUSTING TOE IN/TOE OUT - A4 CAMBER SYSTEM - COURSE ADJUSTMENT Adjustment Ring Stop - Not touching camber clamp Stop - In position for one (1) camber, touching camber clamp Adjustment Ring Adjustment Ring Phillips Screw Stop - In position for one (1) camber, tou ...

  • Invacare Top End TerminatorTM SS - page 36

    Terminator SS 36 Part No. 1052712 Rev D FIGURE 12 - ADJUSTING TOE IN/TOE OUT - A4 CAMBER SYSTEM - FINE ADJUSTMENT Adjustment Ring Stop - In position for one (1) camber, touching camber clamp Stop - Not touching camber clamp Adjustment Ring Phillips Screw Camber Clamp Stop - Not touching camber clamp Adjustment Ring Camber Clamp Adjustment Ring S ...

  • Invacare Top End TerminatorTM SS - page 37

    Part No. 1052712 Rev D 37 Terminator SS FIGURE 13 - ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) Indexing Marks (MUST be set to Same Mark on BOTH Suspension Tubes) NEVER OPERATE THE WHEELCHAIR WITH BOTH ENDS OF THE INDEXING TAPE SHOWING. WHEELS SECTION 5 ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) (FIGURE 13) WARNING ALW ...

  • Invacare Top End TerminatorTM SS - page 38

    Terminator SS 38 Part No. 1052712 Rev D ADJUSTING WHEELBASE WIDTH NOTE: Perform this procedure one (1) side of the wheelchair at a time for ease of adjustment. CAMBER TUBE 2000 (FIGURE 14) NOTE: The wheelbase width can be increased/decreased by 1-inch. 1. Remove the rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the man ...

  • Invacare Top End TerminatorTM SS - page 39

    Part No. 1052712 Rev D 39 Terminator SS REPLACING AXLE TUBE (FIGURE 16) NOTE: The camber bar is always mounted to the BOTTOM of the wheelchair frame. NOTE: There is no need to remove the two (2) camber clamps when replacing the axle tube. 1. A4 CAMBER SYSTEM ONLY - Note the position of the camber inserts so they can be installed at the same posi ...

  • Invacare Top End TerminatorTM SS - page 40

    Terminator SS 40 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS 6. Pull the existing axle tube through one (1) of the camber clamps. 7. A4 CAMBER SYSTEM ONLY - Remove toe adjustment rings from the existing axle tube. 8. Pull the existing axle tube through the other camber clamp and remove from the wheelchair. 9. Slide the new axle tube through o ...

  • Invacare Top End TerminatorTM SS - page 41

    Part No. 1052712 Rev D 41 Terminator SS Place "L" Square Here 90° Angle Flat Edge of Camber Tube Ground/ Floor FIGURE 17 - ADJUSTING THE AXLE TUBE - CAMBER TUBE 2000 CAUTION A4 CAMBER SYSTEM ONLY - DO NOT close the quick-release levers or tighten the hex screws and locknuts without camber inserts in the axle tube. Damage to the axle t ...

  • Invacare Top End TerminatorTM SS - page 42

    Terminator SS 42 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS 10. Reposition the camber inserts to the highest degree of camber. Refer to ADJUSTING REAR WHEEL CAMBER in this section of the manual. 11. Repeat STEP 3. 12. Close the LEFT camber clamp. Refer to OPENING/CLOSING CLAMPS in this section of the manual. 13. Rotate the RIGHT toe adjustme ...

  • Invacare Top End TerminatorTM SS - page 43

    Part No. 1052712 Rev D 43 Terminator SS REPLACING/ADJUSTING CASTERS (FIGURE 19) CAUTION Changing the size of and/or repositioning the front casters can affect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual BEFORE performing this procedure. 1. Remove the bolt and locknut that secure the fro ...

  • Invacare Top End TerminatorTM SS - page 44

    Terminator SS 44 Part No. 1052712 Rev D ADJUSTING FRONT CASTER HEIGHT (FIGURE 20) CAUTION Changing the height of the front casters can affect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual BEFORE performing this procedure. NOTE: When changing a rear wheel/front caster to a different size a ...

  • Invacare Top End TerminatorTM SS - page 45

    Part No. 1052712 Rev D 45 Terminator SS WHEELS SECTION 5 WHEEL LOCK ADJUSTMENT/REPLACEMENT (FIGURE 2 1) NOTE: Invacare recommends LOW mount wheel locks when engaging in any contact sport. NOTE: Before adjusting or replacing the High/Low mount wheel locks, ensure that the tires are inflated to the recommended psi on the sidewall of the tire. 1. L ...

  • Invacare Top End TerminatorTM SS - page 46

    Terminator SS 46 Part No. 1052712 Rev D SECTION 6 FOOTREST/ANTI-TIPPER FOOTREST / ANTI-TIPPER WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, ...

  • Invacare Top End TerminatorTM SS - page 47

    Part No. 1052712 Rev D 47 Terminator SS INSTALLING/ADJUSTING OPTIONAL CLAMP ON RAISED FOOTREST (FIGURE 2) INSTALLING 1. Install the two (2) half clamps onto either side of the wheelchair frame approximately 2-inches above existing footrest with two (2) allen screws provided. 2. Repeat for the opposite side of the wheelchair. 3. Slide the clamp o ...

  • Invacare Top End TerminatorTM SS - page 48

    Terminator SS 48 Part No. 1052712 Rev D SECTION 6 FOOTREST/ANTI-TIPPER FOOTREST / ANTI-TIPPER FIGURE 3 - INSTALLING/ADJUSTING OPTIONAL A4 FOOTREST Allen Screws Footrest Tube Flat Screws Footplate Flat Screws DEPTH HEIGHT ANGLE FOOTPLATE DEPTH ADJUSTMENT 1. Loosen, but do not remove the four (4) flat screws and locknuts that secure footplate to t ...

  • Invacare Top End TerminatorTM SS - page 49

    Part No. 1052712 Rev D 49 Terminator SS FIGURE 4 - ANTI-TIPPER REPLACEMENT/ADJUSTMENT 1-1/2 to 2-inch clearance Anti-tipper Release Buttons Anti-tipper Bar Anti-tipper Socket Camber Clamp Hole ANTI-TIPPER REPLACEMENT/ADJUSTMENT (FIGURE 4) WARNING Anti-tippers MUST BE attached at all times. Inasmuch as the ANTI-TIPPERS are an option on this wheel ...

  • Invacare Top End TerminatorTM SS - page 50

    Terminator SS 50 Part No. 1052712 Rev D SUSPENSION SECTION 7 SUSPENSION WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. ELASTOMERS AND SUSPENSION CAUTION Weather conditions may affect elastomers. Invacare recommends that elastomers be ...

  • Invacare Top End TerminatorTM SS - page 51

    Part No. 1052712 Rev D 51 Terminator SS FIGURE 1 - REPLACING REAR ELASTOMERS LOWER Elastomer Recessed Spacer Telescoping Tube Mounting Bolt Locknut Nylon Washer Nylon Washer Suspension Arm UPPER Elastomer 4. Install the locknut onto the mounting bolt. NOTE: It may be necessary to compress the rear suspension system to install the locknut onto th ...

  • Invacare Top End TerminatorTM SS - page 52

    Terminator SS 52 Part No. 1052712 Rev D Elastomer Fork Bolt Fork Stem SUSPENSION SECTION 7 NOTE: Caster not shown for clarity. DETAIL B DETAIL C REPLACING FRONT ELASTOMERS (FIGURE 2) WARNING Ensure the detent ball protrudes past the fork BEFORE use. Otherwise, injury or damage may occur. 1. Remove the bolt and locknut securing the fo ...

  • Invacare Top End TerminatorTM SS - page 53

    Part No. 1052712 Rev D 53 Terminator SS Receiver Tube Receiver Tube Clamp Suspension Tube Marks FIGURE 3 - REMOVING/INSTALLING SUSPENSION TUBES Axle Tube Camber Clamp Suspension Tube Hex Bolts Locknuts Camber Insert DETAIL "B" - SUSPENSION TUBE HARDWARE REMOVING/INSTALLING/REPLACING SUSPENSION TUBES (FIGURE 3) NOTE: Invacare recommends ...

  • Invacare Top End TerminatorTM SS - page 54

    Terminator SS 54 Part No. 1052712 Rev D SECTION 7 SUSPENSION 4. Close the receiver tube clamps. Refer to OPENING/CLOSING CLAMPS in SECTION 5 of the manual. 5. Reinstall the rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 5 of this manual. 6. Adjust suspension to correspond to the user's weight. Refer to REPLACING REAR ELAST ...

  • Invacare Top End TerminatorTM SS - page 55

    Part No. 1052712 Rev D 55 Terminator SS SECTION 7 SUSPENSION 3. If necessary, refer to REPLACING/ADJUSTING CASTERS in PROCEDURE 5 of the manual to replace the casters or adjust the caster position. 4. After replacing or adjusting the caster size/position, refer to ADJUSTING FRONT CASTER HEIGHT in PROCEDURE 5 of the manual to add/remove fork spac ...

  • Invacare Top End TerminatorTM SS - page 56

    Terminator SS 56 Part No. 1052712 Rev D PROCEDURE 7 SUSPENSION SUSPENSION 13. Install the rear wheels into the camber inserts. Refer to REMOVING/INSTALLING REAR WHEELS in PROCEDURE 5 of this manual. 14. Adjust the axle tube. Refer to ADJUSTING THE AXLE TUBE in PROCEDURE 5 of this manual. NOTE: The performance of the wheelchair will be affected i ...

  • Invacare Top End TerminatorTM SS - page 57

    Part No. 1052712 Rev D 57 Terminator SS REPOSITIONING QUICK RELEASE LEVERS (FIGURE 6) NOTE: This procedure should only be performed if quick release levers are on top of the axle mounting tube and interfere with the desired rear seat-to-floor adjustment. This procedure will position the quick release lever on the bottom of the axle tube. 1. Remo ...

  • Invacare Top End TerminatorTM SS - page 58

    Terminator SS 58 Part No. 1052712 Rev D NOTES NOTES NOTES ...

  • Invacare Top End TerminatorTM SS - page 59

    Part No. 1052712 Rev D 59 Terminator SS LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal ...

  • Invacare Top End TerminatorTM SS - page 60

    Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare and Top End are registered Elyria, Ohio USA Mississauga Ontario trademarks of Invacare Corporation. 44036-2125 L4Z 4G4 Canada Yes, you can. , A4 and Terminator are 800-333-6900 800-668-5324 tr ade mar ks o f Invacare Corporation. Dual Grip is a reg ...

Manufacturer Invacare Category Mobility Aid

Documents that we receive from a manufacturer of a Invacare Top End TerminatorTM SS can be divided into several groups. They are, among others:
- Invacare technical drawings
- Top End TerminatorTM SS manuals
- Invacare product data sheets
- information booklets
- or energy labels Invacare Top End TerminatorTM SS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Invacare Top End TerminatorTM SS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Invacare Top End TerminatorTM SS, service manual, brief instructions and user manuals Invacare Top End TerminatorTM SS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Invacare Top End TerminatorTM SS.

Similar manuals

A complete manual for the device Invacare Top End TerminatorTM SS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Invacare Top End TerminatorTM SS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Invacare Top End TerminatorTM SS.

A complete Invacare manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Invacare Top End TerminatorTM SS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Invacare Top End TerminatorTM SS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Invacare Top End TerminatorTM SS, that we can find in the current document
3. Tips how to use the basic functions of the device Invacare Top End TerminatorTM SS - which should help us in our first steps of using Invacare Top End TerminatorTM SS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Invacare Top End TerminatorTM SS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Invacare Top End TerminatorTM SS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Invacare Top End TerminatorTM SS?

Use the form below

If you did not solve your problem by using a manual Invacare Top End TerminatorTM SS, ask a question using the form below. If a user had a similar problem with Invacare Top End TerminatorTM SS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)