English dropdown-ico

Manual Robomow RS 630

54 pages Not applicable
Download

Go to site of 54

Summary
  • Robomow RS 630 - page 1

    Operating & Safety Manual RS MODELS WWW .ROBOMOW .COM / WWW .ROBOMOW .EU DOC601 1A ...

  • Robomow RS 630 - page 2

    I Introduction The products are manufactured by F . Robotics Acquisitions (Friendly Robotics). CE approved. © Friendly Robotics, 2012-A. All rights reserved. No part of this document may be photocopied, reproduced, electronically transmitted or translated without the prior written consent of Friendly Robotics. Product, product specifications and t ...

  • Robomow RS 630 - page 3

    II Robomow RS 630 W arning Decal Definitions These are the symbols on Robomow ® ; Read them carefully before operating Robomow ® . DANGER! Sharp rotating blades. Keep hands and feet away . Serious injury can occur . Caution – Do not touch rotating blade(s) 1. Safety alerts symbol – W ARNING – This is a dangerous power tool. Use care when op ...

  • Robomow RS 630 - page 4

    III Introduction Safety W arnings & Precautions Use 1. Read this Operating and Safety Manual carefully and be familiar with the controls and the proper use of Robomow ® before operating Robomow ® . 2. Never allow children or people unfamiliar with these instructions to use Robomow ® . 3. Never mow while people, especially children, or pets a ...

  • Robomow RS 630 - page 5

    IV Robomow RS 630 31. Replace worn or damaged parts for safety . 32. Use only the original equipment and accessories. It is not permitted to modify the original design of Robomow ® . All modifications are made at your own risk. 33. Maintenance/ Servicing of Robomow ® should be according to manufacturer instructions. 34. Batteries – Do not open ...

  • Robomow RS 630 - page 6

    V Introduction How Robomow W orks for Y ou Perform a One-Time Setup before operating Robomow for the first time. [Detailed instructions are in the following chapters] • Y ou will install a wire around the entire lawn and around protected areas within the lawn area. This wire is the Perimeter Wire; it sets the boundaries for Robomow . Small pegs a ...

  • Robomow RS 630 - page 7

    VI Robomow RS 630 1 Robomow ® 6 Operating & Safety Manual 1 1 Extension Cable 20 meters (65 ft.), (Low voltage cable). 2 Perimeter Wire Used to create a virtual wall for your Robomow . 7 DVD – Setup and Operation Video. 12 Power Box Used to deactivate (halt) the automatic operation mode and reactivate it as needed. Also provides indication o ...

  • Robomow RS 630 - page 8

    VII Introduction Main Parts Robomow ® 1. Operating Lamp 2. Bumper with touch sensitive sensors 3. STOP Button / Carrying Handle 4. Operating Panel Under the Hood 1. Bumper Door 2. Mowing Height Indicator 3. Mowing Adjustment Knob 4. Safety Switch Base Station 1. Base Station Head (Charging Adaptor) 2. Base 3. Flippers (x2) 4. Stakes (x6) Power Box ...

  • Robomow RS 630 - page 9

    VIII T able Of Contents Chapter 1 Planning Ahead ............................................................................................................................................. 1 Planning the Perimeter Wire’s Layout ...................................................................................................................... ...

  • Robomow RS 630 - page 10

    1 Planning Ahead Chapter 1 Planning Ahead Getting your lawn ready for Robomow is rather simple. Still, as each lawn is unique, we recommend you get acquainted with the setup process before you actually create the perfect setting for your lawn. Please watch the setup video on the Robomow DVD. This V ideo will walk you through the complete setup proc ...

  • Robomow RS 630 - page 11

    2 Robomow RS 630 If your lawn does not match this description, read the next Sections to find the style of your lawn. If your lawn is “Main Zone Only”, you can skip to Section 1.4 of this chapter to determine Base Station location. 1.2.2 Main Zone + Sub-Zone(s) T ype Lawn This type of lawn consists of more than one zone and these zones are conn ...

  • Robomow RS 630 - page 12

    3 Planning Ahead “Separated Zones” type lawn consists of two or more zones that are not connected. Robomow cannot drive between these zones. If you answer “yes” to at least one of the following questions, your lawn is of the “Separated Zones” type.  Are parts of your lawn separated by fences, sidewalks, or other objects that Robomow ...

  • Robomow RS 630 - page 13

    4 Robomow RS 630 Or: A Separated Zone larger than 200 m² (2150 ft²)  This large separated area needs a separate operation of the mower .  An additional Base Station (optional accessory) should be installed in the additional area. 1.4 Select Base Station Location Robomow’s Base Station is placed along the Perimeter Wire. This is where the ...

  • Robomow RS 630 - page 14

    5 Planning Ahead 1.5 Determine Power Box Location  The Power Box will be connected to the Base Station.  Select a suitable location for the Power Box to be mounted on the wall near the plug socket.  Robomow’s 20 m (65 ft.) Extension Cable will be connected to the Power Box. The length of the Extension Cable must not be changed. The Power ...

  • Robomow RS 630 - page 15

    6 Planning Ahead 1.6.3 Distances from Edge (Pools, Ponds, Cliffs, etc.)  RoboRuler is used to measure the distance from the edge, where the wire is to be placed.  In certain cases, near bodies of water such as pools and ponds, or great height differences such as clif fs, it is required to maintain a greater distance from the Edge (see Section ...

  • Robomow RS 630 - page 16

    7 Initial Setup Chapter 2 Initial Setup Recommendation, before you start: During setup, you will insert pegs into the ground. T o make this task smoother , we recommend you mow your lawn and water it before starting. Getting Ready Make sure all parts needed for setup are within reach. Have Robomow box nearby , so to have all items available. In add ...

  • Robomow RS 630 - page 17

    8 Robomow RS 630 2.1.2 Laying the Perimeter Wire  The Perimeter Wire is secured to the ground by the pegs supplied with Robomow . Insert pegs every few meters and at corners. At this early stage set a minimum number of pegs. Later , after testing the wire setup, you will insert all necessary pegs.  After uncoiling Sections of wire, before ins ...

  • Robomow RS 630 - page 18

    9 Initial Setup  There should be a distance between the Island Wire and the Perimeter Wire:  Maintain a minimum of 1.5 m (5 ft.) between the Island wire and the Perimeter Wire.  Maintain a minimum of 1.5 m (5 ft.) between wires of adjacent islands. CAUTION: Setting the Perimeter Wire Anti Clockwise around the obstacle will cause mower to d ...

  • Robomow RS 630 - page 19

    10 Robomow RS 630  Lay the T emplate on the ground at the entrance to the Narrow Pass:  The arrow points towards the entrance to the Narrow Pass, in the direction of the Sub-Zone.  Insert by hand (half-way in) 7 pegs into the 7 holes numbered 1 – 7 .  Lift the T emplate up so the pegs are left loosely stuck in the ground.  Lay the ...

  • Robomow RS 630 - page 20

    11 Initial Setup  Leave the four pegs 4 – 7 standing half-way out.  They will later be connected to the wire after you finish setting the Perimeter Wire around the Sub-Zone.  Complete setting Perimeter Wire around the Sub-Zone until you come back to peg #4.  Lay the Perimeter Wire through pegs 4 – 7 in sequential order . Insert the ...

  • Robomow RS 630 - page 21

    12 Robomow RS 630 2.3.3 A pond, swimming pool, or watercourse at lawn’ s edge OR: Grass level more than 70 cm (2 ft.) higher than outer area.  Set the Perimeter Wire at least 1.2 m (4 ft.) from the water (or chasm).  Y ou may provide a fence or another barrier along the lawn’s edge by the water , so Robomow will surely detect it.  The ...

  • Robomow RS 630 - page 22

    13 Initial Setup  Peg the two Perimeter Wires down to the ground using the same peg leaving enough loose wire. T wist together the two loose parts. Insert the end of the wire without the connector into the hole of the other wire’s connector . Use a small flat screwdriver to tighten and secure this wire into the connector . 2.6 Assembling the B ...

  • Robomow RS 630 - page 23

    14 Robomow RS 630  Feed both the Perimeter Wire (A) and the Extension Cable (B) through the slot in the rear side of the Base Station.  Attach the Perimeter Wire connector to the Base Station Head (A).  Attach the 20 m (65 ft.) Extension Cable to the Base Station Head (B), if not already connected.  Make sure that the Perimeter Wire and ...

  • Robomow RS 630 - page 24

    15 Initial Setup 2.8 Installing the Power Box 2.8.1 Determining Power Box Location Consider the following in order to install the Power Box at its optimal location:  Locate it outside the lawn perimeter .  Select an easily accessed spot.  Prefer a dry and sheltered location.  Select an area close to an electrical outlet.  The Power B ...

  • Robomow RS 630 - page 25

    16 Robomow RS 630 Chapter 3 Preparing Robomow Before using Robomow for the first time, you have to perform some simple preliminary settings. Once preparations are complete, your Robomow will be ready to mow your lawn. 3.1 Adjust the Cutting Height Blade Cutting Range: 20 – 80 mm (0.8 – 3 inches) T o adjust the cutting height of the blade, do th ...

  • Robomow RS 630 - page 26

    17 Preparing Robomow If you wish to quit the process during setup: 3.3.1 Select Language: 3.3.2 Set Date: 3.3.3 Set Time: 3.3.4 T est Base Station Position  Press to start the test. Robomow drives towards the Base Station and Searching Base is displayed. If the mower does not start the test, then one of the following messages will be displayed: ...

  • Robomow RS 630 - page 27

    18 Robomow RS 630 3.3.6 Main Zone Area If a Sub-Zone exists. Do not include it in the area size required here. Y ou will be promoted to define it later . 3.3.7 T est Wire Position T esting Wire... Robomow follows the wire around the edge to test the wire position.  W alk along the side of Robomow while it is following the edge. Having completed ...

  • Robomow RS 630 - page 28

    19 Preparing Robomow If you do have Sub-Zone(s): 3.3.9 Going to Sub-Zone 1 Robomow will follow the Perimeter Wire around the edge towards the Sub-Zone. 3.3.10 Press ST OP at Zone Entry  When Robomow is at least 5 m (16 ft.) inside that Sub-Zone – Press Stop to learn the distance from the Base Station to Sub-Zone Entry . If you don’t have an ...

  • Robomow RS 630 - page 29

    20 Robomow RS 630 Chapter 4 Robomow Operation 4.1 Automatic Operation  During the One-T ime Setup, you have asked to define the size of your lawn. Robomow will derive the required Mowing T ime for your lawn.  The One-T ime Setup configures Robomow to perform automatically the following cycle of operations:  Depart from the Base Station. ? ...

  • Robomow RS 630 - page 30

    21 Robomow Operation 4.3 Lawn Options If the default lawn option settings need to be changed, several options are available. 4.3.1 Inactive Time The Inactive T ime menu is used to set times when the mower will be Inactive. Inactive operating times can be set for specific days of the week, and for specific hours each day . רויא ינפל T o sele ...

  • Robomow RS 630 - page 31

    22 Robomow RS 630 T o select Inactive Hours: 4.3.2 Operations 4.3.2.1 Intensity The Intensity option controls the number of operations needed to cover the lawn size.  There are cases where the selected lawn area is not completely mowed and patches of uncut grass are visible.  This can occur when the:  Zone area set is smaller than the actu ...

  • Robomow RS 630 - page 32

    23 Robomow Operation 4.3.2.2 Interval  The Interval option controls the time between mowing cycles. Shorter intervals between cycles create shorter growth periods. Longer intervals allow for longer grass growth periods.  Grass growth rate changes during the year (depending on temperature, grass type, fertilizing and etc.).  The default Int ...

  • Robomow RS 630 - page 33

    24 Robomow RS 630 4.3.3.1 Add  If you are adding a Sub-Zone: Sub-Zone 1 Set. Add another?  If you are adding a Separated Zone : If the selected area is too big for a single operation, Base Station Recommended will be displayed. An additional Base Station (optional accessory) will allow multiple operations in larger separated zones. 4.3.3.2 Re ...

  • Robomow RS 630 - page 34

    25 Robomow Operation 4.3.3.3 Edit T o edit the Main Zone : Only the Area of the Main Zone can be changed. T o edit a Sub-Zone: The Area and the Sub-Zone Entry can be changed.  T o change the Area of a Sub-Zone :  Sub-Zone Entry There are two methods to change the Sub-Zone Entry , using Update Distance or Learn Distance .  Update Distance : ...

  • Robomow RS 630 - page 35

    26 Robomow RS 630 T o edit a Separated Zone: The following can be changed for a Separated Zone : Area, Edge T erminate and Base Station.  T o change the Area of a Separated Zone: Edge T erminate indicates to Robomow how far to mow the edge before starting to mow the inner lawn.  T o change the Edge T erminate settings of a Separated Zone: The ...

  • Robomow RS 630 - page 36

    27 Robomow Operation 4.3.5 Near Wire Follow In the Main Zone, when Robomow completes its operation, or when the Home button instructs it to Go T o Base, it drives itself to the Base Station. Robomow drives along the Perimeter Wire with a dynamic offset (not centered) to prevent wheel tracks along the same path. This return behavior can be turned of ...

  • Robomow RS 630 - page 37

    28 Robomow RS 630 4.4.2 Anti-Theft The Anti-Theft feature alarms the surroundings in the event of unintended removal of the mower from its designated area. By default Anti-Theft is turned Off. T o turn the Anti-Theft On for the first time: T ip: Select an easily memorized number . Write it down (Bottom of Chapter 8), and keep it in a safe place. 4. ...

  • Robomow RS 630 - page 38

    29 Robomow Operation 4.4.4 Time And Date T ime And Date have already been set during the One-Time Setup. They can be updated using the T ime And Date option.  T o Set T ime  T o change T ime Format  T o Set Date  T o change Date Format 4.4.5 Language  T o change Language Press to select Time and Date from the Mower Options menu . Pre ...

  • Robomow RS 630 - page 39

    30 Robomow RS 630 4.4.6 LCD Contrast  T o change LCD Contrast Level 4.4.7 Sound Use the Sound option to turn all non-safety sounds off. 4.5 Manual Operation Manual Operation is used when mowing the lawn at unscheduled times, or when the lawn has to be cleared of people and debris before the mowing starts. T o initiate Manual Operation when Robom ...

  • Robomow RS 630 - page 40

    31 Using the Power Box Chapter 5 Using the Power Box 5.1 Power Box Alerts Alert Event Docking Indicator is lit. Mower is in its Base Station. Operating Indicato r is lit. Mower is not in its Base Station. On/Off Buttin Indicator is lit. Mowing schedule is Off. Wire Indicator - Flashes and Beeps The Perimeter Wire is cut, disconnected, or too long. ...

  • Robomow RS 630 - page 41

    32 Robomow RS 630 Chapter 6 Charging - - Shock, injury , electrocution hazard! Never use the Power Box or charge the Robomow in areas where extreme dampness or wet contact is likely . Never use a Power Box when the leads are damaged. Use only the recommended Power Box for your Robomow . Important: It is recommended to place the Power Box in a shelt ...

  • Robomow RS 630 - page 42

    33 Charging  Charging will begin immediately , and the LCD will display:  When the Battery is fully charged Ready message will be Display .  Keep the mower connected through out the winter .  Once the season starts, just place Robomow in its Base Station to begin automatic operation as the season before. ...

  • Robomow RS 630 - page 43

    34 Robomow RS 630 Chapter 7 T roubleshooting 7.1 T ext error-messages Robomow continuously monitors its operation. It produces text messages to assist you in smoothly running it: text messages in case of an operational fault as well as text messages that prompt the user to perform a certain action.  Usually , if the mower stops, a message is dis ...

  • Robomow RS 630 - page 44

    35 T roubleshooting Message Displayed Probable Cause/Event Corrective/User Action Cross Outside - The Perimeter Wire is too close to the edge. - The lawn slope is too big. - Robomow does not succeed to turn in place at the edge and it causes the mower to slip out of the area. - Robomow has slipped out of the Perimeter Wire lope because of slopping ...

  • Robomow RS 630 - page 45

    36 Robomow RS 630 Message Displayed Probable Cause/Event Corrective/User Action Start elsewhere - Drive wheel motors have been working under a severe load during automatic or manual operation. - Check to insure the mower is not stuck, allowing the drive wheels to slip. - Check the ground around the mower for holes or indentations. Fill with dirt an ...

  • Robomow RS 630 - page 46

    37 T roubleshooting Problem Encountered Probable Cause/Event Corrective/User Action Mower does not dock properly and sometimes miss the Base Station contacts - Height differences between the lawn and the Base Station surface. - Fill some ground to flat the lawn with the Base Station to allow smooth entrance to the station. - Wire underneath the Bas ...

  • Robomow RS 630 - page 47

    38 Robomow RS 630 Chapter 8 Specifications Dimensions 73.5 cm (L) x 66 cm (W) x 31 cm (H) / (29” L x 26” W x 12.2” H). Weight 19 kg (51 lb.) Includes batteries. Noise level ECO Mode: 66 dB Measured (Guaranteed – 68 dB) . Hi Power: 72 dB Measured (Guaranteed – 74 dB) . Mowing Width 56 cm Cutting Width – 2 Blades of 28 cm (22”). Mowing ...

  • Robomow RS 630 - page 48

    39 Maintenance and Storage Chapter 9 Maintenance and Storage 9.1 Maintenance of the Mowing Deck Robomow is a dedicated mulching mower . It may accumulate clippings under the mowing deck, particularly when mowing wet or damp grass. W arning Severe injury hazard! Always turn the Safety Switch off before lifting the mower . Blades are very sharp. They ...

  • Robomow RS 630 - page 49

    40 Robomow RS 630 9.2 Maintenance of the Blades  Examine the cutting blades for damage once a month.  Use only sharp blades. Replace any damaged blades.  Replace blades according to the table below , or more often if they are severely dulled. Lawn Size Instructions Less than 1000 m 2 (1 1000 ft 2 ) At the end of the season , swap the blade ...

  • Robomow RS 630 - page 50

    41 Maintenance and Storage 9.3 Disposing the Old Battery Pack IMPORT ANT Do not place used batteries in your household trash. The battery must be collected, recycled, or disposed of in an environmentally sound manner . Return the old power pack to an approved battery recycler . 9.4 Splicing the Perimeter W ire If the Perimeter Wire needs to be spli ...

  • Robomow RS 630 - page 51

    42 Robomow RS 630 Chapter 10 Accessories Blade Set Keep a spare blade set on hand. Sharp blades are important for safety and good cutting performance. Battery Used to renew the life of the existing battery and refresh cutting capacity . Perimeter Wire For larger lawns or additional zones. Peg Pack (50) For larger lawns or additional zones. Wire Rep ...

  • Robomow RS 630 - page 52

    43 T ips for maintaining your lawn Robomow ® - Lawn care has never been so easy Best time to mow Mow your lawn when the grass is dry . This prevents the clippings from clumping and leaving piles on the lawn. Mow it late in the day rather than during the heat of the day . Mowing frequency Mow often, producing short, small clippings. During the acti ...

  • Robomow RS 630 - page 53

    W arranty Card W arranty Card RS Series Limited W arranty Friendly Robotics warrants to the original purchaser that the RS series ‘Product’ is free from defects in materials and workman ship when used under normal residential* purposes for a period of 24 months, 12 months for the batteries, beginning from the date of purchase. Product accessori ...

  • Robomow RS 630 - page 54

    www .robomow .com / www .robomow .eu Robomow ® Hotline AT . 0664/180.88.09 BE . 070.660.124* CH . 0900.888.101*** CZ . 800.909.898 DE . 09005.7626669** DK . 7025.2303 FR . 0892.230.199* LU . 0900.4300.4090* NL . 0900.762.6669* NO . 4000.7719 SE . 0771.895.895 * Max ½ 0.35 p/m. ** Werktags von 9-12 und 13-16 Uhr 0,59 ½ pro Minute aus dem deutsche ...

Manufacturer Robomow Category Robot Mower

Documents that we receive from a manufacturer of a Robomow RS 630 can be divided into several groups. They are, among others:
- Robomow technical drawings
- RS 630 manuals
- Robomow product data sheets
- information booklets
- or energy labels Robomow RS 630
All of them are important, but the most important information from the point of view of use of the device are in the user manual Robomow RS 630.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Robomow RS 630, service manual, brief instructions and user manuals Robomow RS 630. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Robomow RS 630.

Similar manuals

A complete manual for the device Robomow RS 630, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Robomow RS 630 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Robomow RS 630.

A complete Robomow manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Robomow RS 630 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Robomow RS 630, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Robomow RS 630, that we can find in the current document
3. Tips how to use the basic functions of the device Robomow RS 630 - which should help us in our first steps of using Robomow RS 630
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Robomow RS 630
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Robomow RS 630 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Robomow RS 630?

Use the form below

If you did not solve your problem by using a manual Robomow RS 630, ask a question using the form below. If a user had a similar problem with Robomow RS 630 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)