Manual Field Controls CK-43

8 pages 0.54 mb
Download

Go to site of 8

Summary
  • Field Controls CK-43 - page 1

    2630 Airport Road · Kinston , NC 28504 Phone: 252-522-3031· Fax: 252-522-0214 www.fieldcontrols.com 24 VAC SYSTEM CONTROL KIT Mode l: CK-43 The CK-43 is designed for use with the SWG Series Power Venter for controlling Natural Gas and L.P. Gas Draft Induced appliances. Control kits control the operation of SWG Power Venters. Control Kits can also ...

  • Field Controls CK-43 - page 2

    Page 2 INSTALLATION INSTRUCTIONS M OUNTING J UNCTION B OX The junction box can be mounted at the v enter or remotely mounted away from the venter. (See Figure 1 & Figure 2) 1. Remove one of the knockouts from the side of the junction box where the pressure switch is mounted. Install the flexible conduit connector onto the CK-43 junction box and ...

  • Field Controls CK-43 - page 3

    Page 3 DRAFT CONTROL INSTALLATION See Figure 4 for typical vent system layout. CAUTION: This draft control is shipped as a single acting draft control. If the draft control is not being used on a gas draft induced furnace, remove the gate stop on the draft control ring before installing. C OLLAR I NSTALLATION This control is shipped with a collar p ...

  • Field Controls CK-43 - page 4

    Page 4 D RAFT C ONTROL I NSTALLA TION IN T YPE B V ENT P IPE CAUTION: DO NOT use the supplied collar when mounting draft control to Type B Vent Pipe. Install by using a Type B Vent Pipe Tee. 1. Install a vent pipe reducer or increaser into the inner pipe and fasten using sheet metal screws. (See Figures 6 & 7) 2. The opening of the Type B Vent ...

  • Field Controls CK-43 - page 5

    Page 5 PROVING SWITCH ADJUSTMENTS After proper air flow is established, the pressure switch adjustment is made by turning pressure switch adjustment screw clockwise (See Figure 10) until burner operation stops. Turn the adjustment screw counter clockwise until burner ignites. Turn the adjustment screw an additional 1/4 to 3/4 turn counterclockwise ...

  • Field Controls CK-43 - page 6

    Page 6 SYSTEM CONTROL CHECK OUT PROCEDURES 1. Adjust the thermostat to call for heat and observe the power venting system for proper operation sequence (Repeat if necessary). a. Thermostat calls for heat. b. Relay is energized and venter motor starts. c. Pressure switch closes and burner starts. d. Thermostat is satisfied, the burner stops. e. This ...

  • Field Controls CK-43 - page 7

    Page 7 INSTALLATION INFORMATION MODEL NO.: ____________________________________________________________ INSTALLER’S NAME: _____________________________________________________ INSTALLER’S COMPANY: _________________________________________________ INSTALLER’S PHONE NO.: ________________________________________________ DATE OF INSTA LLATION: __ ...

  • Field Controls CK-43 - page 8

    Page 8 P/N 46190700 Rev D 11/07 ...

Manufacturer Field Controls Category Switch

Documents that we receive from a manufacturer of a Field Controls CK-43 can be divided into several groups. They are, among others:
- Field Controls technical drawings
- CK-43 manuals
- Field Controls product data sheets
- information booklets
- or energy labels Field Controls CK-43
All of them are important, but the most important information from the point of view of use of the device are in the user manual Field Controls CK-43.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Field Controls CK-43, service manual, brief instructions and user manuals Field Controls CK-43. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Field Controls CK-43.

A complete manual for the device Field Controls CK-43, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Field Controls CK-43 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Field Controls CK-43.

A complete Field Controls manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Field Controls CK-43 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Field Controls CK-43, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Field Controls CK-43, that we can find in the current document
3. Tips how to use the basic functions of the device Field Controls CK-43 - which should help us in our first steps of using Field Controls CK-43
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Field Controls CK-43
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Field Controls CK-43 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Field Controls CK-43?

Use the form below

If you did not solve your problem by using a manual Field Controls CK-43, ask a question using the form below. If a user had a similar problem with Field Controls CK-43 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)