English dropdown-ico

Manual Cannon Mag 20 Dt/Hs

28 pages 4.18 mb
Download

Go to site of 28

Summary
  • Cannon Mag 20 Dt/Hs - page 1

    OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized t o repair or replace this unit. You may obtain service b y: • calling CANNON® at 1-800-2 27-6433; • returning your do wnrigger to the F actor y Service Center; • sending or taking your d ownrigger to any CANNON® Authorized Serv ...

  • Cannon Mag 20 Dt/Hs - page 2

    2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches. 3. Swivel Head This relays the cable at the end of the boom to lower the wei ght. ...

  • Cannon Mag 20 Dt/Hs - page 3

    3 Mag 20 DT New Features Magnum Power The Mag 20 DT/HS and Mag 20 DT/TS feature improved tolling weight capacity, retrieval rate, and quality. The Mag 20 DTs can now accommodate trolling weights up to 20lbs. The newly improved Mag 20 DTs also feature a high retrieval rate up to 250 feet per minute. Mag 20 DT/TS Features The Mag 20 DT/TS (Tournament ...

  • Cannon Mag 20 Dt/Hs - page 4

    4 Downrigger Mounting on Boat s A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job. Due to the great variety of boats available, mounting your downrigger can be a dilemma. Havin ...

  • Cannon Mag 20 Dt/Hs - page 5

    5 Side Rail Mounting Side/Rail mounts can be mounted to a welded T section. They can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces. You can also use these for mounting to a very narrow side gunwale. There is a plate pro ...

  • Cannon Mag 20 Dt/Hs - page 6

    6 NOTE: When using the telescopic boom, we strongly recommend the use of a deck plate on all boats to provide adequate stability for the downrigger. The Low-Profile Swivel Base mounting follows the same procedure as for the deck plate except that four 1/4”-20 x 2 1/2" truss head screws are used to fasten the mounting base and four additional ...

  • Cannon Mag 20 Dt/Hs - page 7

    7 Mounting the Downrigger on the Base Slide body over the lip of the base, with boom outboard or facing the stern. Lift Lock Knob to hold threaded shaft clear of base until body completely covers base. Turn Lock Knob clockwise to tighten the downrigger to the base. Tip: Periodically check base to ensure integrity. The base should be replaced at lea ...

  • Cannon Mag 20 Dt/Hs - page 8

    8 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds ...

  • Cannon Mag 20 Dt/Hs - page 9

    9 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders and the loss t ...

  • Cannon Mag 20 Dt/Hs - page 10

    10 Wiring Y our Downrigger Your Boat's Electrical Condition It is important to make sure that your boat is properly set up before installing your Mag 20 DT with Positive Ion Control (PIC). Whenever a boat is in water, various submerged parts interact to create weak electrical currents. These weak electrical currents must be controlled to exten ...

  • Cannon Mag 20 Dt/Hs - page 11

    11 FUSE / BREAKER SPECIFICATI ONS: 30 Amp, 32 Volt, waterproof, fast blow. WIRE SPECIFICATIONS: 0-15 ft. (0-5 meters) 10 gauge 15-25 ft. (5-8 meters) 8 gauge 25-30 ft. (8-9 meters) 6 gauge CAUTION: When using wire longer than that provided with your unit, follow the above chart. When running more than 30 feet from the battery, contact a qualified e ...

  • Cannon Mag 20 Dt/Hs - page 12

    12 Clutch Knob 3-Position Motor Swit ch Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. Tthis is called drop back. Attach the fishing line firmly into the line release. Press and hold the toggle switch down to lowe ...

  • Cannon Mag 20 Dt/Hs - page 13

    13 NOTE: Make sure that the clutch is well tightened when using powered descent or ascent. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball. (See "Blowback") NOTE: If your reel continues to slip no matter how hard you tighten the brake adjust knob, try this suggestion. 1. Unwind ...

  • Cannon Mag 20 Dt/Hs - page 14

    14 The Short S top System The Short Stop system is composed of three critical components: the electronic unit, the reel set screw, and the trolling weight insulat or. While the downrigger cable is in the water, there is a minute electrical current that flow s between the cable and the grounded metal boat components in the water. When the cable clea ...

  • Cannon Mag 20 Dt/Hs - page 15

    15 How the Positive Ion Control System Works The PIC system uses an internal circuit that passes the voltage through the drive train of the Mag 20 DT to the reel set screw. The set screw contacts the cable. Care must be taken to ensure contact between the cable and the set screw when replacing the cable. The positive Ion Control system applies a va ...

  • Cannon Mag 20 Dt/Hs - page 16

    16 Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you. The farther the weight is behind you, the shallower the weight is. ...

  • Cannon Mag 20 Dt/Hs - page 17

    17 T rouble Shooting PROBLEM: Up or down will not work. SOLUTION: Check the battery cable polarity then check the battery voltage. A properly connected and charged battery is important for safety and for proper operation of the downrigger. PROBLEM: The Mag 20 DT/HS Mag 20 DT/TS fails to continue running after toggle switch is pushed up and held m ...

  • Cannon Mag 20 Dt/Hs - page 18

    18 T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action. For example, a slight bend in the tail of a spoon or twist of the hook e ...

  • Cannon Mag 20 Dt/Hs - page 19

    19 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the following warranty periods, Johnson Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be m ...

  • Cannon Mag 20 Dt/Hs - page 20

    20 Authorized Service Centers Your new Cannon® Downrigger was built to exacting specifications under rigid quality control to p rovide you years of trouble-fr ee operation. If it should ever need adjustment or serv ice, you may send it to any Cannon® Authorized Service Center near you. For a current list of aut horized Cannon Service Center s, in ...

  • Cannon Mag 20 Dt/Hs - page 21

    TM MAG 20 DT/HS 1902200 Form No. 3394903 Rev 12/06 ...

  • Cannon Mag 20 Dt/Hs - page 22

    1 3392500 FRAME - LARGE BLACK (LEXAN) 42 0467695 BRAKE PLATE - REEL 83 9430160 >WASHER - STAR 5/16" [3.EA] 2 4427005 NOSE DECAL MAGNUM 43 1264670 CLUTCH PAD 84 2277002 >UNIVERSAL LINE RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 44 1433074 GEAR - DRIVER WORM 85 3998600 >UNI-STACKER RELEASE 4 2263102 NUT - HEX 1/4"-20 45 9010003 ...

  • Cannon Mag 20 Dt/Hs - page 23

    TM MAG 20 DT/HS/E 1902201 Form No. 3394922 Rev 12/06 ...

  • Cannon Mag 20 Dt/Hs - page 24

    1 3392500 FRAME - LARGE BLACK (LEXAN) 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 83 9340101 >SCREW - SET 3/8"-16 x 5/8" [2.EA] 2 4427005 NOSE DECAL MAGNUM 43 0467695 BRAKE PLATE - REEL 84 9430160 >WASHER - STAR 5/16" [3.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 44 1264670 CLUTCH PAD 85 2277002 >UNIVERSAL LINE RELEASE 4 ...

  • Cannon Mag 20 Dt/Hs - page 25

    TM MAG 20 DT/TS 1902205 Form No. 3394908 Rev 12/06 ...

  • Cannon Mag 20 Dt/Hs - page 26

    1 3392505 FRAME - LARGE WHITE (LEXAN) 40 1480070 SHAFT - DRIVE 79 9430160 >WASHER - STAR 5/16" 2 4427005 NOSE DECAL MAGNUM 41 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 80 2200109 >OFFSHORE SALTWATER RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 42 0467695 BRAKE PLATE - REEL 81 3992300 SWIVEL HEAD ASSEMBLY 4 2263102 NUT - HEX 1/4" ...

  • Cannon Mag 20 Dt/Hs - page 27

    TM MAG 20 DT/TS/E 1902206 Form No. 3394921 Rev 12/06 ...

  • Cannon Mag 20 Dt/Hs - page 28

    1 3392505 FRAME - LARGE WHITE (LEXAN) 41 1480070 SHAFT - DRIVE 81 2200109 >OFFSHORE SALTWATER RELEASE 2 4427005 NOSE DECAL MAGNUM 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 82 3992300 SWIVEL HEAD ASSEMBLY 3 9040040 HOOK - 1/4" - 20 ROLLED 43 0467695 BRAKE PLATE - REEL 83 0267001 ► SIDE PLATE (RH) 4 2263102 NUT - HEX 1/4"-20 44 1 ...

Manufacturer Cannon Category Fish Finder

Documents that we receive from a manufacturer of a Cannon Mag 20 Dt/Hs can be divided into several groups. They are, among others:
- Cannon technical drawings
- Mag 20 Dt/Hs manuals
- Cannon product data sheets
- information booklets
- or energy labels Cannon Mag 20 Dt/Hs
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cannon Mag 20 Dt/Hs.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cannon Mag 20 Dt/Hs, service manual, brief instructions and user manuals Cannon Mag 20 Dt/Hs. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cannon Mag 20 Dt/Hs.

Similar manuals

A complete manual for the device Cannon Mag 20 Dt/Hs, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cannon Mag 20 Dt/Hs by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cannon Mag 20 Dt/Hs.

A complete Cannon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cannon Mag 20 Dt/Hs - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cannon Mag 20 Dt/Hs, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cannon Mag 20 Dt/Hs, that we can find in the current document
3. Tips how to use the basic functions of the device Cannon Mag 20 Dt/Hs - which should help us in our first steps of using Cannon Mag 20 Dt/Hs
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cannon Mag 20 Dt/Hs
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cannon Mag 20 Dt/Hs in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cannon Mag 20 Dt/Hs?

Use the form below

If you did not solve your problem by using a manual Cannon Mag 20 Dt/Hs, ask a question using the form below. If a user had a similar problem with Cannon Mag 20 Dt/Hs it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)