English dropdown-ico

Manual Bunn IMIX -3S+A

13 pages 1.22 mb
Download

Go to site of 13

Summary
  • Bunn IMIX -3S+A - page 1

    IMIX ® -3S+ IMIX ® -3S+A IMIX ® -5S+ IMIX ® -5S+A INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Serv ...

  • Bunn IMIX -3S+A - page 2

    2 38987 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor . 2) All othe ...

  • Bunn IMIX -3S+A - page 3

    3 WA RNING ! Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. FA ILURE TO COMPL Y RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD READ THE E ...

  • Bunn IMIX -3S+A - page 4

    4 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Electrical Hook-Up. The 120 volt version of this dispenser has an attached cordset. The mating connector must be a NEMA 5-15R. T o access terminal block for high voltage models without a cordset, remove left side panel. Requirements for ...

  • Bunn IMIX -3S+A - page 5

    5 38987 120513 PLUMBING REQUIREMENTS This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi (138 - 620 kPa) from a 1⁄2” or larger supply line. A shut-off valve should be installed in the line before the dispenser . Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to re ...

  • Bunn IMIX -3S+A - page 6

    6 38987 120513 RUNNING A RINSE SEQUENCE 1. Place the Normal/Program/Rinse switch (page 9) in the “rinse” position. 2. Sequentially at each position, press all of the dispense switches. The dispenser will run for 10 seconds with the hopper(s) disabled. 3. As each position is rinsed, the LCD display will show which position is being rinsed and co ...

  • Bunn IMIX -3S+A - page 7

    7 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur - faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 1 x 24h 37254.0000A 07/04 © 2004 BUNN-O-MA TIC CORPORA TION NOTICE The cleaning instructions noted above are for non-dairy sugar based food ...

  • Bunn IMIX -3S+A - page 8

    8 Adjust tank temperature (190° F maximum) Adjust minimum tank ready temper - ature for lockout (185° maximum) Adjust hopper motor speed for station selected T ANK TEMP XXX° (-) EXIT (+) READY TEMP XXX° (-) EXIT (+) DRINK STRENGTH (-) XX (+) XX° CAL XX° (-) T ank T emp (+) 235 REFILL 155 (-) EXIT (+) PORTION CONTROL ? NO EXIT YES Calibrate te ...

  • Bunn IMIX -3S+A - page 9

    9 D igital B everag e C ontr ol D igital B everage C ontr ol ST OP PROGRAM HOME SCREEN The screen above will be shown when the dispenser is ready for use. While the tank is heating, the water temperature will be displayed until the ready temperature is reached . PROGRAMMING THE DISPENSER The following function screens are in order of appearance. Ea ...

  • Bunn IMIX -3S+A - page 10

    10 PROGRAMMING CUP SIZES - Portion Control Models The cup size can be programmed in portion control models by “EXAMPLE” or “TIME”. Programming by EX- AMPLE is manually pressing desired dispense button, then releasing when the desired cup size is attained. The time required to fill the cup will be stored in the controller memory when moving ...

  • Bunn IMIX -3S+A - page 11

    11 PORTION CONTROL ? NO EXIT YES Press and release right switch (advance to next menu), “T ANK TEMP XXX°” appears on screen. PROGRAMMING THE DISPENSER (cont.) T ANK TEMP XXX° READY TEMP XXX° (-) EXIT (+) STRENGTH ADJ. ? (-) EXIT (+) EXIT YES ENTER P ASSWORD (-) XXXX (+) CALIBRA TION ? EXIT YES LOCKS/DISABLES ? EXIT YES ENABLE ADS ? NO EXIT Y ...

  • Bunn IMIX -3S+A - page 12

    12 XX° CAL XX° (-) T ank T emp (+) PROGRAMMING THE DISPENSER (cont.) DRINK STRENGTH 1 (-) XX (+) PRESS DISPENSE TO CHECK T ASTE T ASTE 1 OK ? NO YES (B) Adjust hopper motor speed for station selected SELECT UNITS ENG EXIT METRIC (D) 235 REFILL 155 (-) EXIT (+) Auger Delay (-) .XX sec (+) Returns to (E) (page 11) Goes to next station. Returns to ( ...

  • Bunn IMIX -3S+A - page 13

    13 PROGRAMMING THE DISPENSER (cont.) RINSE ALARM ? NO EXIT YES HEAD 1 DISABLE ? NO EXIT YES SET P ASSWORD ? (-) XXXX (+) Returns to (G) (page 11) TEST SWITCHES ? Use Switch T o T est TEST HEA TER ? EXIT YES TEST REFILL ? EXIT YES TEST HOT WA TER ? EXIT YES TEST AUGERS ? DISPENSE TO TEST TEST DISPENSE HEAD? DISPENSE TO TEST Returns to (I) (page 11) ...

Manufacturer Bunn Category Coffeemaker

Documents that we receive from a manufacturer of a Bunn IMIX -3S+A can be divided into several groups. They are, among others:
- Bunn technical drawings
- IMIX -3S+A manuals
- Bunn product data sheets
- information booklets
- or energy labels Bunn IMIX -3S+A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bunn IMIX -3S+A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bunn IMIX -3S+A, service manual, brief instructions and user manuals Bunn IMIX -3S+A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bunn IMIX -3S+A.

Similar manuals

A complete manual for the device Bunn IMIX -3S+A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bunn IMIX -3S+A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bunn IMIX -3S+A.

A complete Bunn manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bunn IMIX -3S+A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bunn IMIX -3S+A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bunn IMIX -3S+A, that we can find in the current document
3. Tips how to use the basic functions of the device Bunn IMIX -3S+A - which should help us in our first steps of using Bunn IMIX -3S+A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bunn IMIX -3S+A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bunn IMIX -3S+A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bunn IMIX -3S+A?

Use the form below

If you did not solve your problem by using a manual Bunn IMIX -3S+A, ask a question using the form below. If a user had a similar problem with Bunn IMIX -3S+A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)