English dropdown-ico

Manual Chamberlain 3585S 3/4 HP

40 pages 4.34 mb
Download

Go to site of 40

Summary
  • Chamberlain 3585S 3/4 HP - page 1

    The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Model 3585S 3/4 HP For Residential Use Only Owner’ s Manual ■ Please read this manual and the enc losed safety materials carefully! ■ Fasten the man ual near the garage door after installation. ■ The door WILL NO T CLOSE unles ...

  • Chamberlain 3585S 3/4 HP - page 2

    2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . . 2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3 Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Carton inventory . ...

  • Chamberlain 3585S 3/4 HP - page 3

    3 To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. To prevent possible SERIOUS INJURY OR DEATH: • ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An ...

  • Chamberlain 3585S 3/4 HP - page 4

    FINISHED CEILING Support bracket & fastening hardware is required. See page 12. Safety Reversing Sensor Header Wa ll Access Door Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm) Wa ll - mounted Door Control Motor Unit ONE-PIECE DOOR WITHOUT TRACK 4 Planning Identify the type and height of your garage ...

  • Chamberlain 3585S 3/4 HP - page 5

    5 Y our garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below . Carton Inventor y Straight Door Arm Sectio ...

  • Chamberlain 3585S 3/4 HP - page 6

    To avoid SERIOUS damage to opener, ONLY use bolts/ fasteners mounted in top of motor unit. ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o av oid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the bolt and lock nut from the top of the motor unit. • Place rail onto the bolt mounted on the ...

  • Chamberlain 3585S 3/4 HP - page 7

    7 INST ALLA TION IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of SEVERE INJUR Y or DEA TH: WARNING WARNING WARNING WARNING 1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly balanced door may not reverse when required and co ...

  • Chamberlain 3585S 3/4 HP - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket withi ...

  • Chamberlain 3585S 3/4 HP - page 9

    Lag Screw 5/16"-9x1-5/8" HARD WARE SHO WN ACTU AL SIZE Lag Screws 5/16"-9x1-5/8" Highest Point of Garage Door T ravel V ertical Centerline of Garage Door Header W all Garage Door UP CEILING MOUNT ONL Y W all Mounting Holes Optional W all Mounting Holes The nail hole is for positioning only . Y ou must use lag screws to mount the ...

  • Chamberlain 3585S 3/4 HP - page 10

    Header Bracket Belt Pulley Bracket Temporary Support Header Wall Garage Door Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Belt Pulley Bracket Rail Clevis Pin 5/16"x2-3/4" Ring Fastener HARD WARE SHO WN ACTU AL SIZE 10 INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor ...

  • Chamberlain 3585S 3/4 HP - page 11

    11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ? ...

  • Chamberlain 3585S 3/4 HP - page 12

    12 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are ...

  • Chamberlain 3585S 3/4 HP - page 13

    13 INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of door, at a minimum height of 5' (1.5 m) where small children cannot reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construct ...

  • Chamberlain 3585S 3/4 HP - page 14

    14 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The lights will turn ON and remain ...

  • Chamberlain 3585S 3/4 HP - page 15

    15 INST ALLA TION STEP 9 Electrical Requirements T o av oid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, cont ...

  • Chamberlain 3585S 3/4 HP - page 16

    16 Facing the door fr om inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety rever sing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. IMPORT ANT INFORMA TION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect ...

  • Chamberlain 3585S 3/4 HP - page 17

    17 INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows. Garage door track installation (preferred): • Slip the curved arms ...

  • Chamberlain 3585S 3/4 HP - page 18

    Invisible Light Beam Protection Area Safety Reversing Sensor Safety Reversing Sensor Connect Wire to Opener Quick-Connect Terminals Bell Wire Bell Wire Finished Ceiling 1. Strip wire 7/16" (11 mm) 2. Twist like colored wires together 7/16" (1 1 mm) Quick-Connect T erminals 3. T o release or insert wire, push in tab with screwdriver tip Re ...

  • Chamberlain 3585S 3/4 HP - page 19

    19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace ...

  • Chamberlain 3585S 3/4 HP - page 20

    Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. METAL DOOR Top of Door (Inside Garage) Door Bracket Optional Pla ...

  • Chamberlain 3585S 3/4 HP - page 21

    21 INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) ...

  • Chamberlain 3585S 3/4 HP - page 22

    22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener. 2. Adju ...

  • Chamberlain 3585S 3/4 HP - page 23

    23 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the door control push bar. Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not reverse ...

  • Chamberlain 3585S 3/4 HP - page 24

    24 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weathe ...

  • Chamberlain 3585S 3/4 HP - page 25

    25 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...

  • Chamberlain 3585S 3/4 HP - page 26

    26 OPERA TION IMPOR T ANT SAFETY INSTR UCTIONS T o reduce the risk of SEVERE INJUR Y or DEA TH: Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Secur ...

  • Chamberlain 3585S 3/4 HP - page 27

    27 Using the W all-Mounted Door Control THE SMART CONTR OL P ANEL TM Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening. This door control contains a motion sensing detector that will automatically turn on the light when it detects a person entering the ...

  • Chamberlain 3585S 3/4 HP - page 28

    The 3V2016 lithium batteries for the opener and LED lights (marked “LED and Opener Battery”) should last 5 years. The 3V2450 lithium battery for the proximity lighting (marked “Proximity Battery”) should last 1-2 years. T o replace the batteries, remove the two screws and open the remote control housing. Push the battery out of the holder f ...

  • Chamberlain 3585S 3/4 HP - page 29

    29 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully. Repeat the safety reverse t ...

  • Chamberlain 3585S 3/4 HP - page 30

    30 HAVING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Insta ...

  • Chamberlain 3585S 3/4 HP - page 31

    Bell Wire Safety Reversing Sensor KG 1 3 9 7 5 KG 1 3 9 7 5 Diagnostics Located On Motor Unit "Learn" Button LED or Diagnostic LED Installed Safety Reversing Sensor Diagnostic Chart 31 Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause sign ...

  • Chamberlain 3585S 3/4 HP - page 32

    32 Meaning: This message will appear if the Safety Re versing Sensors are out of alignment, if they are bloc ked or if the wiring is disconnected. T o clear messa g e from Smart Control P anel™ do the following: • Check to see that area is clear between the Safety Reversing Sensors. • Check to see that the Safety Reversing Sensors are not mis ...

  • Chamberlain 3585S 3/4 HP - page 33

    33 *3-Button Remotes If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes Fr om Motor Unit Memory To deactivate any unwanted remote, first ...

  • Chamberlain 3585S 3/4 HP - page 34

    34 To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE “LEARN” BUTTON USING THE SMART CONTROL PANEL TM 1. Press the PROG <Learn> button on the Smart Control Panel TM . 2. Press the PROG <Learn> button again to confirm Learn Mode. 3. Enter a fou ...

  • Chamberlain 3585S 3/4 HP - page 35

    8 11 12 6 N OT ICE U P C E I L I N G M O U N T O N L Y 9 7 1 5 10 13 14 L O C K L IGH T 3 4 2 Installation Parts 2 5 6 1 3 7 8 4 Rail Assembly Parts 35 REP AIR P AR TS KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41B5424 Belt pulley bracket 3 41B3869-3 Complete trolley assembly 4 109B33 Trolley clip 5 2777BD One-piece T-rail 2778BD Compl ...

  • Chamberlain 3585S 3/4 HP - page 36

    36 Motor Unit Assembly Parts DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSEMBL Y Grey Wire Y ellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 1 15 19 8 17 5 18 9 10 16 14 13 12 6 6 11 7 7 7 7 KEY PART NO. NO. DESCRIPTION 1 41A4371 Belt Cap 2 41A4885-5 Gear and sprocket assembly Complete with: Spring washer, thrust washer, retaining ...

  • Chamberlain 3585S 3/4 HP - page 37

    37 ACCESSORIES 370LM 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 377LM Extension Brackets: (Optional) For safety sensor installation onto the wall or floor . Wireless Ke yless Entr y with Security ✚ ® : Enables homeowner to ...

  • Chamberlain 3585S 3/4 HP - page 38

    38 NOTES ...

  • Chamberlain 3585S 3/4 HP - page 39

    39 NOTES ...

  • Chamberlain 3585S 3/4 HP - page 40

    © 2008, The Chamberlain Group, Inc. 114A3616 All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SER VICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS Y OUR TELEPHONE. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-528-9131 www .liftmaster .com For prof essional installation, parts and service, contact ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain 3585S 3/4 HP can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- 3585S 3/4 HP manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain 3585S 3/4 HP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain 3585S 3/4 HP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain 3585S 3/4 HP, service manual, brief instructions and user manuals Chamberlain 3585S 3/4 HP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain 3585S 3/4 HP.

Similar manuals

A complete manual for the device Chamberlain 3585S 3/4 HP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain 3585S 3/4 HP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain 3585S 3/4 HP.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain 3585S 3/4 HP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain 3585S 3/4 HP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain 3585S 3/4 HP, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain 3585S 3/4 HP - which should help us in our first steps of using Chamberlain 3585S 3/4 HP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain 3585S 3/4 HP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain 3585S 3/4 HP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain 3585S 3/4 HP?

Use the form below

If you did not solve your problem by using a manual Chamberlain 3585S 3/4 HP, ask a question using the form below. If a user had a similar problem with Chamberlain 3585S 3/4 HP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)