English dropdown-ico

Manual Pelco IS210

24 pages 2.53 mb
Download

Go to site of 24

Summary
  • Pelco IS210 - page 1

    INST ALLA TION C3428M-A (1/08) IS210 Series Camclosure ® Integrated Camera Sy stem ...

  • Pelco IS210 - page 2

    ...

  • Pelco IS210 - page 3

    C3428M-A (1/08) 3 Contents Important Safety Ins tructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . ...

  • Pelco IS210 - page 4

    4 C3428M-A (1/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...

  • Pelco IS210 - page 5

    C3428M-A (1/08) 5 REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...

  • Pelco IS210 - page 6

    6 C3428M-A (1/08) Description The IS210 Series Camclosure ® is a wedge-style integrate d camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the IS210-CM corner mount. The IS210 system is shipped fully a ssembled. System components include a cover , base with camera an ...

  • Pelco IS210 - page 7

    C3428M-A (1/08) 7 Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the IS210. Use the screwdriver bit (supplied) to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2). Figure 2. Rem ...

  • Pelco IS210 - page 8

    8 C3428M-A (1/08) Figure 3. Fixed Mounting Pattern Figure 4. Adjustable Mounting Patter n FIXED MOUNTING PATTERN ADJU S TABLE MOUNTING PATTERN ...

  • Pelco IS210 - page 9

    C3428M-A (1/08) 9 INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with # 8 stainless steel screws (not supplied) of the appropriate length. Adjustable mounting pattern only: Adjust the ...

  • Pelco IS210 - page 10

    10 C3428M-A (1/08) Figure 5. Removing the Wiring Plug 4. Insert the hole plug (supplied) into the hole in the base of the Camclosure (refer to Figure 6). Figure 6. Installin g the Hole Plug 5. Pull the wiring through the conduit opening (refer to Figure 7 on page 11): a. Use a 1/16-inch hex head wrench to loosen the hex head set screw . b. Use a sc ...

  • Pelco IS210 - page 11

    C3428M-A (1/08) 11 Figure 7. Removing th e Conduit Cover 6. Install a 0.75-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes o f the mounting pl ate. Attach the base to the mounting plate with the three 8-32 x 0.37 5-inch screws and washers pre viously removed. 7. Attach the base ...

  • Pelco IS210 - page 12

    12 C3428M-A (1/08) REINSTALL CAMERA MODULE Reinstall the camera module (refer to Figure 8). Make sure the top of the camera is oriented properly; the lens housing contains a label that reads TOP . NOTE: T o prevent damage to the camera or lens, install the camera in the correct hole positions of the mounting bracket. Figure 8. Camera Insta llation ...

  • Pelco IS210 - page 13

    C3428M-A (1/08) 13 DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS210-DN or IS210-CH model. Figure 10. Adjusting the IS210-DN/C H Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Automatic Gain Co ntrol The automatic gain control (AGC) adju sts the image au tomatically to comp ...

  • Pelco IS210 - page 14

    14 C3428M-A (1/08) SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts. Set SW4-4 to enable flickerless operation. The camera removes the eff ...

  • Pelco IS210 - page 15

    C3428M-A (1/08) 15 Adjusting V ertical Phase Y ou may need two people when synchronizing the cameras: one at the camera, the other at the monitor to observe the vertical roll and the effect of any camera adjustments. T o synchronize the cameras: 1. Choose a reference camera to which all other cameras will be phased. 2. Select the camera to synchron ...

  • Pelco IS210 - page 16

    16 C3428M-A (1/08) DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view , l ...

  • Pelco IS210 - page 17

    C3428M-A (1/08) 17 DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 12 to adjust the IS210-DW or IS210-CW model. Figure 12. Adjusting the IS210-DW/C W Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set SW1-1 to ON for NTSC. Set it to OFF for P AL. The default se ...

  • Pelco IS210 - page 18

    18 C3428M-A (1/08) SW1-4: Auto White Balance/Ma nual White Balance Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the vide o is all white. 3. While holding the background in place, set SW1-4 to OFF . A green block and a white ...

  • Pelco IS210 - page 19

    C3428M-A (1/08) 19 SW1-8: Day/Night Operation (DW models o nly) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the general light levels at which th ...

  • Pelco IS210 - page 20

    20 C3428M-A (1/08) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS210-DW and IS210-CW Series Camclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are n ot necessary . V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vertic ...

  • Pelco IS210 - page 21

    C3428M-A (1/08) 21 Service Connector The IS210 Series Camclosure integrated camera system includes a service connector that outputs ca mera video. Use it at the installation site to set up the field of view and focus the camera. Figure 1 4. Service Connector Pelco offers two optional items that plug directly into the service connector: CST150 compa ...

  • Pelco IS210 - page 22

    22 C3428M-A (1/08) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 180° T ilt 180° Construction Aluminum base and cover , steel camera mounting bracket Finish Gray polyester powder coa t Environment Low temperature, indoor/ou tdoor Operating T emperature -50° to 122°F (-46° to 50°C); de-ices to -10°F (-23°C) Heater T urns on at 50°F ...

  • Pelco IS210 - page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise proved defective in materi al or workmanship for a period of one year after the da te of shipment. Exception s to this warrant y are as noted be low: • Five years on fiber opt ic products and TW3 000 Series unshielded twisted pair (UTP) ...

  • Pelco IS210 - page 24

    Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | G ermany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco IS210 can be divided into several groups. They are, among others:
- Pelco technical drawings
- IS210 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco IS210
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco IS210.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco IS210, service manual, brief instructions and user manuals Pelco IS210. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco IS210.

Similar manuals

A complete manual for the device Pelco IS210, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco IS210 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco IS210.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco IS210 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco IS210, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco IS210, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco IS210 - which should help us in our first steps of using Pelco IS210
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco IS210
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco IS210 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco IS210?

Use the form below

If you did not solve your problem by using a manual Pelco IS210, ask a question using the form below. If a user had a similar problem with Pelco IS210 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)