English dropdown-ico

Manual Kenwood DDX7037

44 pages 1.98 mb
Download

Go to site of 44

Summary
  • Kenwood DDX7037 - page 1

    © B54-4469-00/00 (MV/XV/VV) DDX8037 DDX8047 DDX8067 DDX7037 DDX7047 DDX7067 MONIT OR WITH D VD RECEIVER INST ALLA TION MANU AL 附 DVD 接收機顯示器 安裝說明書 附 DVD 接收机显示器 安装说明书 DVD 수신기장착 모니터 설치 설명서 DDX8_7037_M_Install.indd 1 DDX8_7037_M_Install.indd 1 05.5.20 10:24:17 PM 05.5.20 10:24:1 ...

  • Kenwood DDX7037 - page 2

    2 | English Ac cessories 1 ..........1 2 ..........1 3 ..........1 4 ..........1 5 ..........2 6 ..........6 7 ..........6 8 ..........1 DDX8_7037_M_Install.indd 2 DDX8_7037_M_Install.indd 2 05.5.20 10:24:17 PM 05.5.20 10:24:17 PM ...

  • Kenwood DDX7037 - page 3

    English | 3 Installation Pr ocedure 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. M ake the proper input and output wire connections for each unit. 3. Connec t the speaker wires of the wiring harness. 4. Connec t the wiring harness wires in the following order: ground, battery , ignition. 5. Conne ...

  • Kenwood DDX7037 - page 4

    4 | English C onnec tion TV ANTENNA INPUT TO MONITOR UNIT B C B C PRK SW – + + B C A A If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (gr ound), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power sour ce running through the fuse box. IConnection cable (Inc ...

  • Kenwood DDX7037 - page 5

    English | 5 + + + + FRONT L FRONT R REAR L REAR R ANT. CONT P CONT EXT.CONT REVERSE ILLUMI REMO.CONT MUTE IConnection cable (Included in the Navigation system) Connection cable (Included in the TV tuner). Wiring harness (Accessory 1) T o front left speaker Wiring harness (Accessory 2) Rear view Navigation S ystem (Optional) T o front right speaker ...

  • Kenwood DDX7037 - page 6

    6 | English Sy stem Connection (DD X8037/DDX8047/DD X8067) FRONT REAR WOOFER SUB CENTER A V OUT A V IN 2 CAMERA REAR VIEW A V IN 1 A V OUT ■ Front Preout • Audio left output ( White) • Audio right output (Red) ■ Rear Preout • Audio left output ( White) • Audio right output (Red) ■ Subwoof er Preout • Audio left output ( White) • A ...

  • Kenwood DDX7037 - page 7

    English | 7 Sy stem Connection (DD X7037/DDX7047/DD X7067) FRONT REAR WOOFER SUB A V OUT CAMERA REAR VIEW A V IN A V OUT ■ Front Preout • Audio left output ( White) • Audio right output (Red) ■ Rear Preout • Audio left output ( White) • Audio right output (Red) ■ Subwoof er Preout • Audio left output ( White) • Audio right output ...

  • Kenwood DDX7037 - page 8

    8 | English Installation for Monitor/Pla yer Unit Accessory 4 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) Make sure that the unit is installed securely in place. If th ...

  • Kenwood DDX7037 - page 9

    English | 9 ■ Installation on T oyota, Nissan or Mitsubishi Car using Br ackets Installing in Japanese -Made Cars Car Bracket Accessory 6 (M5x6mm) or Accessory 7 (M5x7mm) Accessory 6 (M5x6mm) or Accessory 7 (M5x7mm) Accessory 3 (For NISSAN Car) DDX8_7037_M_Install.indd 9 DDX8_7037_M_Install.indd 9 05.5.20 10:24:21 PM 05.5.20 10:24:21 PM ...

  • Kenwood DDX7037 - page 10

    10 | English Installation of Remote c ontrol unit ■ Install the remote control unit holder ( Acc essor y 8 ). Double-stick tape (included) Remote control holder 8 T o prevent the Remote control unit from dropping down under y our foot, install it using the Remote control unit holder . I f the Remote control unit drops down under driving pedals , ...

  • Kenwood DDX7037 - page 11

    English | 11 Removing Monitor Unit ■ Removing the Hard Rubber F rame (escutcheon) 1. Engage the catch pins on the removal tool 5 and remove the two locks on the lo wer level. Lower the frame and pull it f orward as shown in the figure. 2. When the lower level is r emoved, remo ve the upper two locations. ■ Removing the Unit 1. Remove the hard r ...

  • Kenwood DDX7037 - page 12

    12 | 中文（繁體字） 附件 1 ..........1 2 ..........1 3 ..........1 4 ..........1 5 ..........2 6 ..........6 7 ..........6 8 ..........1 DDX8037_7037_M_Inst_Ch r1.1.indd 12 DDX8037_7037_M_Inst_Ch r1.1.indd 12 05.5.20 2:26:56 AM 05.5.20 2:26:56 AM ...

  • Kenwood DDX7037 - page 13

    中文（繁體字） | 13 安裝程序 1. 為了防止短路，從點火開關中拔出鑰匙，拆下蓄電 池的負極 - 接線。 2. 連接各裝置的輸入、輸出導線。 3. 連接電線束的揚聲器導線。 4. 按照接地導線、蓄電池導線和點火導線的順序連接 電線束。 5. 將電線束的連接器連接到裝置上? ...

  • Kenwood DDX7037 - page 14

    14 | 中文（繁體字） 連接 TV ANTENNA INPUT TO MONITOR UNIT B C B C PRK SW – + + B C A A 如果您將點火裝置電線（紅色）和電池線（黃色）連接 到汽車底盤（接地） ，您可能會導致短路，並造成火災。 請始終將那些電線連接到經過保險絲盒的電源。 連接線（光盤換片機附帶） ? ...

  • Kenwood DDX7037 - page 15

    中文（繁體字） | 15 + + + + FRONT L FRONT R REAR L REAR R ANT. CONT P CONT EXT.CONT REVERSE ILLUMI REMO.CONT MUTE 連接線 （導航系統 附帶） 連接線（TV 調諧器附帶） 電線線束 （附件 1 ） 向前置左揚聲器 電線線束 （附件 2 ） 後視 導航系統 ( 選購 ) 向前置右揚聲器 向後置左揚聲器 向? ...

  • Kenwood DDX7037 - page 16

    16 | 中文（繁體字） 系統連接 (DDX8037/DDX8047/DDX8067) FRONT REAR WOOFER SUB CENTER A V OUT A V IN 2 CAMERA REAR VIEW A V IN 1 A V OUT ■ 前預輸出 • 音頻左輸出（白色） • 音頻右輸出（紅色） ■ 后預輸出 • 音頻左輸出（白色） • 音頻右輸出（紅色） ■ 低音揚聲器預輸出 • 音頻左 ...

  • Kenwood DDX7037 - page 17

    中文（繁體字） | 17 系統連接 (DDX7037/DDX7047/DDX7067) FRONT REAR WOOFER SUB A V OUT CAMERA REAR VIEW A V IN A V OUT ■ 前預輸出 • 音頻左輸出（白色） • 音頻右輸出（紅色） ■ 后預輸出 • 音頻左輸出（白色） • 音頻右輸出（紅色） ■ 低音揚聲器預輸出 • 音頻左輸出（白色） ...

  • Kenwood DDX7037 - page 18

    18 | 中文（繁體字） 安裝顯示器裝置 附件 4 安裝套盒用螺絲刀等折彎 凸耳部位，將其固定。 金屬安裝固定夾板 （選購） 自攻絲螺絲 （選購） 螺絲（M4×8） （選購） 請切實固定裝置。若安裝不穩，可能會出故障。 隔熱牆或金屬支撐 DDX8037_7037_M_Inst_Ch r1.1.indd 18 DDX8 ...

  • Kenwood DDX7037 - page 19

    中文（繁體字） | 19 ■ 使用汽車托架向豐田牌、日產牌或三菱牌汽車安裝時 在日本汽車上安裝時 汽車托架 附件 6 （M5×6mm） 或者附件 7 （M5×7mm） 附件 6 （M5×6mm） 或者附件 7 （M5×7mm） 附件 3 （對於 NISSAN （日產牌）汽車） DDX8037_7037_M_Inst_Ch r1.1.indd 19 DDX8037_7037_M_In ...

  • Kenwood DDX7037 - page 20

    20 | 中文（繁體字） 安裝遙控裝置 ■ 安裝遙控裝置座（附件 8 ） 雙面粘貼膠帶 ( 隨機提供 ) 遙控裝置座 8 為了防止遙控裝置掉落在腳下，請安裝遙控裝置座。如果遙控裝置掉落在操縱踏板下， 將防礙駕駛而導致交通事故。 DDX8037_7037_M_Inst_Ch r1.1.indd 20 DDX8037_7037_M_Ins ...

  • Kenwood DDX7037 - page 21

    中文（繁體字） | 21 拆除顯示器裝置 1. 拉出可拆卸工具 5 的凸耳，拆卸下側兩處 的鎖定裝置。 按圖示要領將框向下壓，再向後拉出。 2 . 下側拆卸後，上側兩處也以同樣方法 拆 卸。 ■ 拆卸方法 1. 參照〈硬橡膠框的拆卸方法〉部分的內容， 拆下硬橡膠框。 2. 卸? ...

  • Kenwood DDX7037 - page 22

    22 | 中文（简体字） 附件 1 ..........1 2 ..........1 3 ..........1 4 ..........1 5 ..........2 6 ..........6 7 ..........6 8 ..........1 DDX8037_7037_M_Inst_SC r1.1.indd 22 DDX8037_7037_M_Inst_SC r1.1.indd 22 05.5.20 11:01:34 PM 05.5.20 11:01:34 PM ...

  • Kenwood DDX7037 - page 23

    中文（简体字） | 23 安装程序 1. 为了防止短路，从点火开关中拔出钥匙，拆下蓄电 池的负极 - 接线。 2. 连接各装置的输入、输出导线。 3. 连接电线束的扬声器导线。 4. 按照接地导线、蓄电池导线和点火导线的顺序连接 电线束。 5. 将电线束的连接器连接到装置上? ...

  • Kenwood DDX7037 - page 24

    24 | 中文（简体字） 连接 TV ANTENNA INPUT TO MONITOR UNIT B C B C PRK SW – + + B C A A 如果您将点火装置电线（红色）和电池线（黄色）连接 到汽车底盘（接地） ，您可能会导致短路，并造成火灾。 请始终将那些电线连接到经过保险丝盒的电源。 连接线（光盘换片机附带） ? ...

  • Kenwood DDX7037 - page 25

    中文（简体字） | 25 + + + + FRONT L FRONT R REAR L REAR R ANT. CONT P CONT EXT.CONT REVERSE ILLUMI REMO.CONT MUTE 连接线 （导航系统 附带） 连接线（TV 调谐器附带） 电线线束 （附件 1 ） 向前置左扬声器 电线线束 （附件 2 ） 后视 导航系统（选购） 向前置右扬声器 向後置左扬声器 向 ...

  • Kenwood DDX7037 - page 26

    26 | 中文（简体字） 系统连接 （DDX8037/DDX8047/DDX8067） FRONT REAR WOOFER SUB CENTER A V OUT A V IN 2 CAMERA REAR VIEW A V IN 1 A V OUT ■ 前预输出 · 音频左输出（白色） · 音频右输出（红色） ■ 后预输出 · 音频左输出（白色） · 音频右输出（红色） ■ 低音扬声器输出 · 音频左输? ...

  • Kenwood DDX7037 - page 27

    中文（简体字） | 27 系统连接 （DDX7037/DDX7047/DDX7067） FRONT REAR WOOFER SUB A V OUT CAMERA REAR VIEW A V IN A V OUT ■ 前预输出 · 音频左输出（白色） · 音频右输出（红色） ■ 后预输出 · 音频左输出（白色） · 音频右输出（红色） ■ 低音扬声器输出 · 音频左输出（白色） · ...

  • Kenwood DDX7037 - page 28

    28 | 中文（简体字） 安装显示器装置 附件 4 安装套盒用螺丝刀等折弯 凸耳部位，将其固定。 金属安装固定夹板 （选购） 自攻丝螺丝 （选购） 螺丝（M4×8） （选购） 请切实固定装置。若安装不稳，可能会出故障。 隔热墙或金属支撑 DDX8037_7037_M_Inst_SC r1.1.indd 28 DDX8 ...

  • Kenwood DDX7037 - page 29

    中文（简体字） | 29 ■ 使用汽车托架向丰田牌、日产牌或三菱牌汽车安装时 在日本汽车上安装时  汽车托架 附件 6 （M5×6mm） 或者附件 7 （M5×7mm） 附件 6 （M5×6mm） 或者附件 7 （M5×7mm） 附件 3 （对于 NISSAN （日产牌）汽车） DDX8037_7037_M_Inst_SC r1.1.indd 29 DDX8037_7037_ ...

  • Kenwood DDX7037 - page 30

    30 | 中文（简体字） 安装遥控装置 ■ 安装遥控装置座（附件 8 ） 双面粘贴胶带 （随机提供） 遥控装置座 8 为了防止遥控装置掉落在脚下，请安装遥控装置座。如果遥控装置掉落在操纵踏板下， 将防碍驾驶而导致交通事故。 DDX8037_7037_M_Inst_SC r1.1.indd 30 DDX8037_7037_M_I ...

  • Kenwood DDX7037 - page 31

    中文（简体字） | 31 拆除显示器装置 1. 拉出可拆卸工具 5 的凸耳，拆卸下侧两处 的锁定装置。 按图示要领将框向下压，再向后拉出。 2 . 下侧拆卸后，上侧两处也以同样方法 拆 卸。 ■ 拆卸方法 1. 参照〈硬橡胶框的拆卸方法〉部分的内容， 拆下硬橡胶框。 2. 卸? ...

  • Kenwood DDX7037 - page 32

    32 | 한 글 부속품 1 ..........1 2 ..........1 3 ..........1 4 ..........1 5 ..........2 6 ..........6 7 ..........6 8 ..........1 DDX8037_7037_M_Inst_Ko r1.1.indd 32 05.5.20 2:33:05 AM ...

  • Kenwood DDX7037 - page 33

    한 글 | 33 설치 순서 1. 단락을 방지하기 위해 이그니션에서 키를 빼고 - 배 터리를 차단합니다． 2. 각 기기의 입출력 와이어를 바르게 접속합니다． 3. 와이어링 하네스와 스피커 와이어를 접속합니다． 4. 어스，배터리，이그니션의 순서로 와이어링 하네스 의 와? ...

  • Kenwood DDX7037 - page 34

    34 | 한 글 접속 TV ANTENNA INPUT TO MONITOR UNIT + + + + FRONT L FRONT R REAR L REAR R B C B C ANT. CONT P CONT EXT.CONT PRK SW – + B C A A REVERSE ILLUMI REMO.CONT MUTE 이그니션 와이어 (빨강) 와 배터리 와이어 (노랑) 를 차대 (접지) 에 연결할 때에 전기 누전을 일으켜 발 화할 수도 있습니다. 이들 ? ...

  • Kenwood DDX7037 - page 35

    한 글 | 35 접속 TV ANTENNA INPUT TO MONITOR UNIT + + + + FRONT L FRONT R REAR L REAR R B C B C ANT. CONT P CONT EXT.CONT PRK SW – + B C A A REVERSE ILLUMI REMO.CONT MUTE 접속 케이블 (네비게이션 시스 템에 포함) 접속 케이블 (TV 튜너에 포함) 와이어링 하네스 (부속품 1 ) 앞 왼쪽 스피커 와이어링 하네? ...

  • Kenwood DDX7037 - page 36

    36 | 한 글 시스템 연결 (DDX8037/DDX8047/DDX8067) FRONT REAR WOOFER SUB CENTER A V OUT A V IN 2 CAMERA REAR VIEW A V IN 1 A V OUT █ 전면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 후면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 서브-우 ...

  • Kenwood DDX7037 - page 37

    한 글 | 37 시스템 연결 (DDX7037/DDX7047/DDX7067) FRONT REAR WOOFER SUB A V OUT CAMERA REAR VIEW A V IN A V OUT █ 전면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 후면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 서브-우퍼 예비출력 ? ...

  • Kenwood DDX7037 - page 38

    38 | 한 글 모니터/플레이어 기기를 위한 설치 부속품 4 마운팅 슬리브의 탭을 스크류 드라이버나 비슷한 연장으로 구부려서 적절한 위치에 부착 하십시오. 메탈 마운팅 스트랩 (상용) 자기-탭핑 나사 (상용) 나사 (M4×8) (상용) 기기가 제자리에 단단히 설치되었는지 확 ...

  • Kenwood DDX7037 - page 39

    한 글 | 39 █ 브래킷을 사용해서 도요타, 닛산 또는 미츠비시 자동차에 설치하기 일제 자동차에 설치하기 자동차 브래킷 부속품 6 (M5×6mm) 또는 부속품 7 (M5×7mm) 부속품 6 (M5×6mm) 또는 부속품 7 (M5×7mm) 부속품 3 (NISSAN 자동 차용) DDX8037_7037_M_Inst_Ko r1.1.indd 39 05.5.20 2:33:14 A ...

  • Kenwood DDX7037 - page 40

    40 | 한 글 리모컨 유닛의 설치 █ 리모컨 유닛 홀더 설치 (액세서리 8 ) 더블 스틱 테이프 (포함) 리모컨 홀더 8 여러분의 발에 리모컨 유닛이 떨어지는 것을 방지하기위해서는, 리모컨 유닛 홀더를 사용해서 설치하십시오. 리모컨 유닛이 드라이브 페달 아래에 떨어지 ...

  • Kenwood DDX7037 - page 41

    한 글 | 41 모니터 유닛 떼어내기 █ 강화 고무 프레임 떼어내기 1. 고정 핀을 제거용 기구 5 에 대고 아래 쪽에있는 두개의 잠금 장치를 떼어내십시오. 프레임을 내려서 그림에 보이는 것처럼 앞으로 당겨내십시오. 2. 아래 쪽을 떼어냈으면, 위쪽의 두 곳도 떼어내 십? ...

  • Kenwood DDX7037 - page 42

    DDX8037_7037_M_Inst_Ko r1.1.indd 42 05.5.20 2:33:16 AM ...

  • Kenwood DDX7037 - page 43

    DDX8037_7037_M_Inst_Ko r1.1.indd 43 05.5.20 2:33:16 AM ...

  • Kenwood DDX7037 - page 44

    DDX8037_7037_M_Inst_Ko r1.1.indd 44 05.5.20 2:33:16 AM ...

Manufacturer Kenwood Category Car Video System

Documents that we receive from a manufacturer of a Kenwood DDX7037 can be divided into several groups. They are, among others:
- Kenwood technical drawings
- DDX7037 manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood DDX7037
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood DDX7037.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood DDX7037, service manual, brief instructions and user manuals Kenwood DDX7037. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood DDX7037.

Similar manuals

A complete manual for the device Kenwood DDX7037, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood DDX7037 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood DDX7037.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood DDX7037 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood DDX7037, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood DDX7037, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood DDX7037 - which should help us in our first steps of using Kenwood DDX7037
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood DDX7037
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood DDX7037 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood DDX7037?

Use the form below

If you did not solve your problem by using a manual Kenwood DDX7037, ask a question using the form below. If a user had a similar problem with Kenwood DDX7037 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)