English dropdown-ico

Manual Graco Series A

16 pages 0.39 mb
Download

Go to site of 16

Summary
  • Graco Series A - page 1

    Fluid Filters 5000 psi (350 bar , 35 MPa) Maximum Working Pressure Model 238620, Series A Exposed Mounting Model 214724, Series E Cover Mounting Model 289310, Series A Cover Mounting Fluid Filter 7252 psi (500 bar , 50 MPa) Maximum Working Pressure Model 237069, Series A Exposed Mounting Surge T anks (with filter) 5000 psi (350 bar , 35 MPa) Maximu ...

  • Graco Series A - page 2

    307296 2 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surge T ank Conversion Kits 4 . . . . . . . . . . . . . . . . . . . . . Operation 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Graco Series A - page 3

    307296 3 Installation T ypical Mountings See Fig. 1 for typical mountings. See page 14 for the mounting hole layout. Install the surge tank or filter near the pump outlet. Position the surge tank so the labels face away from the pump and so the setscrews, near the top and bottom of the tank, face toward the pump. The top of the surge tank must alwa ...

  • Graco Series A - page 4

    307296 4 Surge T ank Conversion Kits Surge T ank Conversion Kits 238634 and 237704 Use Conversion Kits 238634 or 237704 to add a surge tank to a pump. Kit 238634 includes surge tank 238623 (A) and clamp 238630 (B). Kit 237704 includes surge tank 214624 (A), clamp 238630 (B), and attach- ing hardware (C). Connect the surge tank to the fluid outlet ( ...

  • Graco Series A - page 5

    307296 5 Operation Before operating the equipment, be sure the drain valve is closed. Flush the equipment with a compatible solvent to remove oil used for factory testing and rust prevention. If you notice excessive surging at the spray gun, shut off the pump, trigger the gun to relieve fluid pressure, and open the drain valve (D) at the bottom of ...

  • Graco Series A - page 6

    307296 6 Service Pressure Relief Procedure W ARNING SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause serious injury . T o reduce the risk of an injury from injection, splashing fluid, or moving parts ...

  • Graco Series A - page 7

    1007 1 3 2 1 2 3 4 5 6 23 24 25 18 19 20 21 22 10 11 14 12 15 12 16 13 17 See Accessories for other available screens. Replace filter support if ridges are worn down. 7 Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove. 1 2 3 4 Lubricate. 4 307296 7 Parts Model 214724, Series E Model 289310, Series A Include ...

  • Graco Series A - page 8

    05908 1 3 2 1 2 3 4 5 6 10 2 2 8 26 9 See Accessories for other available screens. Replace filter support if ridges are worn down. 7 Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove. 1 2 3 4 Lubricate. 4 28 27 307296 8 Parts Model 238620, Series A Includes items 1–28 Ref No. Part N o. Description Qty Ref ...

  • Graco Series A - page 9

    1 3 2 1 2 3 4 5 6 10 2 2 8 26 9 See Accessories for other available screens. Replace filter support if ridges are worn down. 7 Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove. 1 2 3 4 Lubricate. 4 05909 307296 9 Parts Model 237069 Includes items 1–26 Ref No. Part N o. Description Qty Ref No. Part No. Des ...

  • Graco Series A - page 10

    1004 11 3 2 12 15 14 33 16 15 31 13 1 2 3 5 6 7 8 9 10 24 25 26 27 28 29 11 3 2 12 13 23 30 31 19 17 32 17 21 18 22 34 1 2 See Accessories for other available screens. Replace filter support if ridges are worn down. Do not damage PTFE o-ring (13). Lubricate and bend into kidney shape, then push into groove. T orque to 150 ft–lb (200 N.m). T orque ...

  • Graco Series A - page 11

    05907 11 3 2 14 15 31 1 2 3 5 6 7 8 9 10 12 34 1 2 See Accessories for other available screens. Replace filter support if ridges are worn down. Do not damage PTFE o-ring (13). Lubricate and bend into kidney shape, then push into groove. T orque to 150 ft–lb (200 N.m). T orque to 40 in–lb (4.5 N.m). 4 5 3 1 2 5 3 Lubricate. 6 4 6 6 3 3 5 5 3 3 1 ...

  • Graco Series A - page 12

    1006 1 2 3 6 23 24 25 18 19 20 21 22 14 15 16 13 17 5 3 2 8 9 7 11 10 12 28 27 28 29 3 5 11 Do not damage PTFE o-ring (9). Lubricate and bend into kidney shape, then push into groove. T orque to 150 ft–lb (200 N.m). T orque to 40 in–lb (4.5 N.m). 4 5 3 Lubricate. 6 6 6 5 5 3 3 3 3 4 307296 12 Parts Model 214623, Series A Includes items 1–12, ...

  • Graco Series A - page 13

    307296 13 Accessories Use Only Genuine Graco Parts and Accessories SURGE T ANK CLAMPS 238630 For surge tanks mounted in the fluid outlet of the displacement pump. Install the clamp in the optional outlet at the base of the air motor . Requires 100902 screw , 100016 lockwasher and 100015 nut. 100016 100015 100902 172865 For surge tanks mounted in th ...

  • Graco Series A - page 14

    307296 14 T echnical Data Category Data Maximum Working Pressure Model 237069: 7252 psi (500 bar , 50 MPa) All Other Models: 5000 psi (350 bar , 35 MPa) Weight Model 214623: 30 lb (13 kg) Model 214624: 31.5 lb (14 kg) Model 214724: 13 lb (6 kg) Model 214725: 34 lb (15 kg) Model 214726: 34 lb (15 kg) Model 237069: 10.5 lb (4.5 kg) Model 238620: 10.5 ...

  • Graco Series A - page 15

    307296 15 Dimensions 1005 1008 A* B C D L F E J G K D H F E L K C A* B * For models 238620 and 238623, add approximately 6 in. (152 mm) to the “A” dimension to account for the drain tube and fitting. J Filters Paint Surge T anks Mastic Surge T anks Dimensions 238620 237069 214724 & 289310 214624 & 238623 214726 214623 214725 A (see * no ...

  • Graco Series A - page 16

    307296 16 The Graco Standard W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from ...

Manufacturer Graco Category Water Dispenser

Documents that we receive from a manufacturer of a Graco Series A can be divided into several groups. They are, among others:
- Graco technical drawings
- Series A manuals
- Graco product data sheets
- information booklets
- or energy labels Graco Series A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco Series A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco Series A, service manual, brief instructions and user manuals Graco Series A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco Series A.

Similar manuals

A complete manual for the device Graco Series A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco Series A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco Series A.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco Series A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco Series A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco Series A, that we can find in the current document
3. Tips how to use the basic functions of the device Graco Series A - which should help us in our first steps of using Graco Series A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco Series A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco Series A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco Series A?

Use the form below

If you did not solve your problem by using a manual Graco Series A, ask a question using the form below. If a user had a similar problem with Graco Series A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)