-
Hampton Direct H15-NG1 - page 1
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-516a MODELS: H15-NG1 Natural Gas H15-LP1 Propane 12/17/07 H15 Direct V ent Gas Fireplace Owners & Installation Manual W ARNING: If the information in these instructions are not followed exactly , a fi re or explosion may result causing property damage, ...
-
Hampton Direct H15-NG1 - page 2
2 Hampton ® H15-1 Direct V ent Freestanding Gas Stove HAMPT ON ® Direct V ent Freestanding Gas Stove UNIT DIMENSIONS T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Hampton ® Gas Stove by FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. The H15-1 is a hand crafted appliance and has been designed to provide you with all th ...
-
Hampton Direct H15-NG1 - page 3
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 3 T ABLE OF CONTENTS Optional W all Thermostat ........................................... 34 Optional Remote Control ............................................ 34 Final Check ................................................................. 34 Wiring Diagrams .................................. ...
-
Hampton Direct H15-NG1 - page 4
4 Hampton ® H15-1 Direct V ent Freestanding Gas Stove This is a copy of the label that accompanies each Direct V ent Freestanding Gas Stove. We have printed a copy of the contents here for your review . SAFETY LABEL NOTE: Hampton ® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit ...
-
Hampton Direct H15-NG1 - page 5
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 5 REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chap ter 10 (2) Revise 10.8. 3 by adding the following a dditional requi rements: (a) For all side wall hor izontally ve nted gas fueled e quipment insta lled in every dwelling, bui lding or str ucture used in whole or in part for residential pu rpo ...
-
Hampton Direct H15-NG1 - page 6
6 Hampton ® H15-1 Direct V ent Freestanding Gas Stove IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The Direct V ent Freestanding Gas Stove must be installed in accordance with these instruc- tions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdiction to determine the need for a permit prior ...
-
Hampton Direct H15-NG1 - page 7
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 7 INST ALLA TION (825mm), a maximum depth of 36" (914mm), and minimum height of 24" (610mm) from top of unit to ceiling. 6) We recommend that you plan your instal- lation on paper using exact measurements for clearances and fl oor protection before actually installing this appliance. H ...
-
Hampton Direct H15-NG1 - page 8
8 Hampton ® H15-1 Direct V ent Freestanding Gas Stove LOCA TING YOUR GAS ST OVE When selecting a location for your stove, ensure that the clearances listed above are met as well as ensuring that there is adequate accessibility for servicing and proper operation. MANUF ACTURED MOBILE HOME ADDITIONAL REQUIREMENTS 1) Ensure that structural members ar ...
-
Hampton Direct H15-NG1 - page 9
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 9 INST ALLA TION 9) Remove 2 screws from unit. 10) Place grommet in rear plate through the bottom of the opening as shown below . 11 ) Place the blower close to the base of the unit and feed the wires through the grommet in the rear plate. 16) Slide the Rear Access Panel back into posi- tion and ...
-
Hampton Direct H15-NG1 - page 10
10 Hampton ® H15-1 Direct V ent Freestanding Gas Stove INST ALLA TION PRECAUTIONS These venting systems are engineered products that have been designed and tested for use with the H15-NG1, and H15-LP1. The warranty will be voided and serious fi re, health or other safety hazards may result from any of the fol- lowing actions: 1) Installation of a ...
-
Hampton Direct H15-NG1 - page 11
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 11 EXTERIOR VENT TERMINAL LOCA TIONS A= Clearance above grade , v eranda, porch, deck, or balcony * (min. 12"/30cm) B= Clearance to win dow or door that may be op ened *(12"/30cm) C= Clearance to permanently closed window *(min. 12"/30cm) D= Vertical clearance to ventilated s offi ...
-
Hampton Direct H15-NG1 - page 12
12 Hampton ® H15-1 Direct V ent Freestanding Gas Stove 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Produ ...
-
Hampton Direct H15-NG1 - page 13
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 13 Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Products ® Amerivent Direct Metal-Fab ® Sure Seal Security Secure V ent ® Attic Insulation Shield 12” 46DV A-IS - N/A from FPI N/A N/A 4DAIS12 N/A SV4RSA Attic Insulation ...
-
Hampton Direct H15-NG1 - page 14
14 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Pipe Length V ertical T ermination Cap S torm Collar Flashing Ceiling Firestop 24" Pipe Length Adj.Pipe Length 1 1" - 14-5/8" 90 Elbow o Horizontal T ermination Cap W all Thimble Vinyl Siding S tandoff (Optional) RIGID PIPE VENTING SYSTEMS Horizontal or V ertical T erminations A ...
-
Hampton Direct H15-NG1 - page 15
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 15 H1 H V Horizontal V enting with T wo (2) 90 o Elbows Option V H + H1 A) 1' Min. 3' Max. B) 2' Min. 4' Max. C) 3' Min. 5' Max. D) 4' Min. 6' Max. E) 5' Min. 7' Max. F) 6' Min. 8' Max. Horizontal V enting with T wo (2) 90 o Elbows Optio ...
-
Hampton Direct H15-NG1 - page 16
16 Hampton ® H15-1 Direct V ent Freestanding Gas Stove H1 H V V ertical V enting with T wo (2) 90 o Elbows Option V H V + V1 A) 1' Min. 4' Max. 2' Min. B) 2' Min. 5' Max. 3' Min. C) 3' Min. 6' Max. 4' Min. D) 4' Min. 7' Max. 5' Min. E) 5' Min. 8' Max. 6' Min. V ertical V en ...
-
Hampton Direct H15-NG1 - page 17
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 17 Offset to V ertical T erminations V enting Arrangements - Horizontal T erminations VENTING ARRANGEMENTS V ertical T erminations Systems for Residential Manufactured and Mobile Homes The shaded area in the diagram below shows all allowable combinations of straight vertical and offset to vertica ...
-
Hampton Direct H15-NG1 - page 18
18 Hampton ® H15-1 Direct V ent Freestanding Gas Stove V enting Arrangements - V ertical T erminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagram shows the allowable vertical terminations. VERTICAL TERMINA TION WITH CO-LINEAR FLEX SYSTEM THE APPLIANCE MUST NOT BE ...
-
Hampton Direct H15-NG1 - page 19
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 19 DV ST OVE HORIZONT AL VENT KIT (#946-1 16 & #946-216) INST ALLA TION Review the following sequence of instructions which are typical of most installations. The sequence may vary depending on wall thick- ness. Refer to the "Exterior V ent T erminal Locations" and "Rigid Pipe ...
-
Hampton Direct H15-NG1 - page 20
20 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Note: The pipe seam should be fac- ing down. Note: T o make the installation more aes- thetically pleasing, we recommend framing out a square that the cap can be mounted on. 3) Attach the 4" dia. fl ex liner to the vent ter- minal ensuring that the fl ex overlaps the collar of the vent ...
-
Hampton Direct H15-NG1 - page 21
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 21 RESIDENTIAL AND MANUF ACTURED HOMES / MOBILE HOMES MINIMUM HORIZONT AL TERMINA TION INST ALLA TIONS Planning Y our V enting Installation See the "Exterior V ent T erminal Locations" section for requirements. When planning your installation, it will be nec- essary to select the proper ...
-
Hampton Direct H15-NG1 - page 22
22 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Dura-V ent Basic Horizontal Kit # 970 1 90 o Elbow 1 W all Thimble Cover 1 Horiz. Sq. T erm. Cap DURA-VENT TERMINA TION KIT Planning Y our Dura-V ent Installation There are two basic types of Dura-V ent Direct V ent System installations: horizontal termination and vertical termination. Confi ...
-
Hampton Direct H15-NG1 - page 23
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 23 Y ou will require the following components with your new Direct V ent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer . Note: These are the minimum pieces re- quired. Other parts may b ...
-
Hampton Direct H15-NG1 - page 24
24 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Diagram 7 VERTICAL TERMINA TIONS 1) Maintain the 1-1/4" clearances (air spaces) to combustibles when passing through ceil- ings, walls, roofs, enclosures, attic rafter , or other nearby combustible surfaces. Do not pack air spaces with insulation. Check the "V enting Arrangement" ...
-
Hampton Direct H15-NG1 - page 25
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 25 Offset Chart Diagram 12 7) Ensure vent is vertical and secure the base of the fl ashing to the roof with roofi ng rails, slide storm collar over the pipe section and seal with a mastic. 8) Install the vertical termination cap by twist locking it. Notes: a) For multistorey vertical installati ...
-
Hampton Direct H15-NG1 - page 26
26 Hampton ® H15-1 Direct V ent Freestanding Gas Stove CONVERTING CLASS-A MET AL CHIMNEY OR MASONR Y CHIMNEY T O DIRECT VENT SYSTEM There are two different types of direct vent conversion systems listed below . Follow the appropriate directions for your installation. A) Through an existing factory built metal chimney going through the ceiling: A t ...
-
Hampton Direct H15-NG1 - page 27
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 27 4) Assemble the desired lengths of Black Pipe and Elbows necessary to reach from the appliance adapter up through the support box and fl ashing to proper height as per Dia. 12, local codes. Ensure that all pipe and elbow connections are in their fully twist lock position. 5) Ensure vent is ve ...
-
Hampton Direct H15-NG1 - page 28
28 Hampton ® H15-1 Direct V ent Freestanding Gas Stove GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at p ...
-
Hampton Direct H15-NG1 - page 29
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 29 THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! CONVERSION KIT# 381-969 FROM NG T O LP Each Kit contains one LPG Conversion Kit and one DC Sparker Kit. LPG Conversion Kit Contains: Qty . Part # Description 1 904-575 Burner Orifi ce #55 1 918-590 ...
-
Hampton Direct H15-NG1 - page 30
30 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Installation of the DC Sparker: 19) Remove the control panel by unscrewing the 2 screws. 21) Plug up the Piezo hole with the plastic bushing. 22) Attach the DC sparker generator connector to the valve with a screw . 23) Remove the stove’s rear panel by unscrew- ing the two screws. 24) Attach ...
-
Hampton Direct H15-NG1 - page 31
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 31 27) Install the plastic bushing over the outside of the hole. 28) Attach the ground wire to the DC spark mounting bracket. 29) Attach the DC sparker generator wires to the DC sparker . 26) Insert both the ground wire and the DC sparker generator wire through the hole of the DC spark heat shiel ...
-
Hampton Direct H15-NG1 - page 32
32 Hampton ® H15-1 Direct V ent Freestanding Gas Stove A) D) B) C) LOG SET INST ALLA TION 1) Shut of f the gas supply . 2) Lift off Cast T op. Read the instructions below carefully and refer to the diagrams. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation. The gas log kit conta ...
-
Hampton Direct H15-NG1 - page 33
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 33 9) Place the center cross log on the locating pin in the top of the rear log and position as shown below . Logs must be oriented as shown below. 10) T est fi re to ensure proper light off (make sure fl ame fl ows smoothly from one end of burner to the other). If there is any fl ame hesitat ...
-
Hampton Direct H15-NG1 - page 34
34 Hampton ® H15-1 Direct V ent Freestanding Gas Stove CAUTION Do not connect the millivolt remote control wires to the 120V wires. 3) Install 3 AAA alkaline batteries in transmitter and 4 AA alkaline batteries in the receiver . Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote contro ...
-
Hampton Direct H15-NG1 - page 35
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 35 WIRING DIAGRAMS CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous opera- If any of the original wires as supplied with the appliance must be replaced, it must be replaced with CSA type SEW (200 o C) or its equivalent. This h ...
-
Hampton Direct H15-NG1 - page 36
36 Hampton ® H15-1 Direct V ent Freestanding Gas Stove INST ALLA TION For PROP ANE Units and Units Equipped with DC Spark Boxes* *For installation of the DC Spark Box refer to the LP Conversion instructions in this manual. ...
-
Hampton Direct H15-NG1 - page 37
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 37 AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically - turn the knob at the top right rear corner to adjust to the desired speed. The fan will turn on as the stove comes up to operating temperature. After the unit has been turned off and the unit cooled to below a useful heat ...
-
Hampton Direct H15-NG1 - page 38
38 Hampton ® H15-1 Direct V ent Freestanding Gas Stove COPY OF THE LIGHTING PLA TE INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Push in gas control knob slightly and turn to “PILOT” position. 2) Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control knob in for about 20 seconds after the pilot is lit. R ...
-
Hampton Direct H15-NG1 - page 39
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 39 MAINTENANCE T op View of pilot fl ame MAINTENANCE INSTRUCTIONS 1) Always turn off the valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year . When cleaning the logs, use a soft clean ...
-
Hampton Direct H15-NG1 - page 40
40 Hampton ® H15-1 Direct V ent Freestanding Gas Stove F AN MAINTENANCE If your fan requires maintenance or replacement, access to the fan is through the rear access panel on the back of the unit. IMPORT ANT : These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan sq ...
-
Hampton Direct H15-NG1 - page 41
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 41 11 ) Carefully lift the burner tray assembly out. REMOVING V AL VE If your valve requires maintenance or replace- ment, use the following instructions: Not e: Always close off the gas supply before removing the valve. 1) If optional fan is installed, disconnect power source to stove. 2) Remove ...
-
Hampton Direct H15-NG1 - page 42
42 Hampton ® H15-1 Direct V ent Freestanding Gas Stove P ARTS LIST MAIN ASSEMBL Y Part # Description Part # Description Part # Description 1) 942-601** Casting - T op 2) 942-621** Casting - Side & Leg 3) 942-61 1** Casting - Front 6) 770-066F T op Relief Plate 7) W260280 T op Relief Plate Gasket 8) 770-067F Plate Insulation Holder 9) 942-1 17 ...
-
Hampton Direct H15-NG1 - page 43
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 43 BURNER & LOG ASSEMBL Y Part # Description P ARTS LIST 380-574/P V alve/Pilot Assembly - S.I.T . - NG 60) 910-478 V alve S.I.T . - NG/LPG 904-434 #47 Orifi ce - NG 63) 910-190 Piezo Ignitor & Nut 64) 908-672 Control Panel Decal 65) 490-061 Switch Plate 936-170 Orifi ce Gasket 66) 910- ...
-
Hampton Direct H15-NG1 - page 44
44 Hampton ® H15-1 Direct V ent Freestanding Gas Stove NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
Hampton Direct H15-NG1 - page 45
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 45 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
Hampton Direct H15-NG1 - page 46
46 Hampton ® H15-1 Direct V ent Freestanding Gas Stove NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
Hampton Direct H15-NG1 - page 47
Hampton ® H15-1 Direct V ent Freestanding Gas Stove 47 W ARRANTY Hampton Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T e am carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited life ...
-
Hampton Direct H15-NG1 - page 48
48 Hampton ® H15-1 Direct V ent Freestanding Gas Stove Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________ ...
Do you have a question concerning Hampton Direct H15-NG1?
Use the form below
If you did not solve your problem by using a manual Hampton Direct H15-NG1, ask a question using the form below. If a user had a similar problem with Hampton Direct H15-NG1 it is likely that he will want to share the way to solve it.