English dropdown-ico

Manual Hoshizaki KM-650MRH

54 pages 1.39 mb
Download

Go to site of 54

Summary
  • Hoshizaki KM-650MRH - page 1

    1 Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Models KM-650MAH KM-650MWH KM-650MRH Modular Crescent Cuber Hoshizaki America, Inc. S E RV I C E M A N U A L ™ Number: 73147 Issued: 12-12-2006 ...

  • Hoshizaki KM-650MRH - page 2

    2 IMPOR T ANT Only qualified ser vice technicians should attempt to ser vice or maintain this unit. No such ser vice or maintenance should be under taken until the technician has thoroughly read this Ser vice Manual. HOSHIZAKI provides this man ual primar ily to assist qualified ser vice technicians in the ser vice and maintenance of the unit. Sh ...

  • Hoshizaki KM-650MRH - page 3

    3 Please re vie w this manual. It should be read carefully bef ore the icemaker is serviced or maintenance operations are perf or med. Only qualified ser vice technicians should ser vice and maintain the icemaker . This manual should be made a v ailab le to the technician prior to ser vice or maintenance. CONTENTS I. Specifications .............. ...

  • Hoshizaki KM-650MRH - page 4

    4 III. T echnical Inf or mation ...................................................................................................... 23 A. W ater Circuit and Refr igeration Circuit ........................................................................ 23 1. KM-650MAH (air-cooled) ................................................................. ...

  • Hoshizaki KM-650MRH - page 5

    5 I. Specifications A. Icemaker 1. KM-650MAH (air-cooled) Note: We reserve the right to make changes in specifications and design without prior notice. SPECIFICATION NO. 06A019 ISSUED: 10/10/2006 ITEM : HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MAH AC SUPPLY VOLTAGE 208-230/60/1 (3 wire with neutral for 115V) AMPERAGE 6.6 A ( 5 Min. Freeze AT ...

  • Hoshizaki KM-650MRH - page 6

    6 2. KM-650MWH (water-cooled) Note: We reserve the right to make changes in specifications and design without prior notice. SPECIFICATION NO. 06A020 ISSUED: 10/10/2006 ITEM : HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MWH AC SUPPLY VOLTAGE 208-230/60/1 (3 wire with neutral for 115V) AMPERAGE 5.3 A ( 5 Min. Freeze AT 104°F / WT 80°F) MINIMUM C ...

  • Hoshizaki KM-650MRH - page 7

    7 3. KM-650MRH (remote air-cooled) Note: We reserve the right to make changes in specifications and design without prior notice. SPECIFICATION DATA NO. 06A021 ITEM: HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MRH AC SUPPLY VOLTAGE 208-230/60/1 (3 wire with neutral for 115V) AMPERAGE 7.1 A ( 5 Min. Freeze AT 104°F / WT 80°F) MINIMUM CIRCUIT AMP ...

  • Hoshizaki KM-650MRH - page 8

    8 B. Condensing Unit 1. URC-5F 24" (610 mm.) 23-1/32" (585 mm.) 19-11/16" (500 mm.) 18-1/8" (460 mm.) 20-15/32" (520 mm.) 21-15/16" (557 mm.) 7/8" DIA. HOLE (23 mm. DIA.) 6-5/16" (160 mm.) 2-15/16" (75 mm.) 18-1/8" (460 mm.) 6/16" x 3/4" (10 mm. x 20 mm.) 4 x 2 (SLO TTED HOLES) 17-1/8" ...

  • Hoshizaki KM-650MRH - page 9

    9 Specifications MODEL: URC-5F SPECIFICATION NO. 06A022 ISSUED: 10/12/2006 ITEM: HOSHIZAKI REMOTE CONDENSER UNIT MODEL URC-5F BEGINNING SERIAL NO. ________________ ENDING SERIAL NO. ___________________ AC SUPPLY VOLTAGE 115/60/1 (Connection to Icemaker) FAN MOTOR 115 V Total 1.3FLA 65W EXTERIOR DIMENSIONS (WxDxH) 21-15/16" x 15-11/16" x ...

  • Hoshizaki KM-650MRH - page 10

    10 II. General Information A. Construction 1. KM-650MAH (air-cooled) Bin Control Ther mostat W ater Supply Inlet Condenser Drier Control Bo x Spra y T ubes Control Switch W ater Pump Float Switch Compressor Expansion V alve F an Motor Hot Gas V alve ...

  • Hoshizaki KM-650MRH - page 11

    11 2. KM-650MWH (water-cooled) Bin Control Ther mostat W ater Supply Inlet Condenser Drier Control Bo x Spra y T ubes Control Switch W ater Pump Float Switch Compressor Expansion V alve W ater Regulator V alv e Hot Gas V alve ...

  • Hoshizaki KM-650MRH - page 12

    12 3. KM-650MRH (remote air-cooled) Bin Control Ther mostat Receiv er T ank W ater Supply Inlet Junction Bo x Drier Control Bo x Spra y T ubes Control Switch W ater Pump Float Switch Compressor Expansion V alve Hot Gas V alve Liquid Line V alve ...

  • Hoshizaki KM-650MRH - page 13

    13 B. Sequence of Operation The steps in the sequence are as outlined below . When po wer is supplied, a 5 second dela y occurs at star tup . Note that the order of the LEDs from the outer edge of the board is 1, 4, 3, 2. 1. One Minute Fill Cycle LED 4 is on. WV opens and the fill period begins. After 1 minute, the board chec ks f or a closed F/S. ...

  • Hoshizaki KM-650MRH - page 14

    14 Components Energized when the Contr ol Switch is in the W ASH P osition The W ASH position on the control switch is used when cleaning and sanitizing the unit. When in the W ASH position, power is supplied to the pump motor . With the cleaning v alve closed, the cleaner and sanitiz er flow ov er the outside of the e v aporator plate assemb ly . ...

  • Hoshizaki KM-650MRH - page 15

    15 C. Control Boar d • A HOSHIZAKI e xclusiv e solid-state control is emplo yed in KM-650MAH, KM-650MWH and KM-650MRH Modular Crescent Cubers. • All models are pretested and f actor y-adjusted. CA UTION 1. F ragile , handle v er y carefully . 2. A control board contains integrated circuits, which are susceptib le to failure due to static discha ...

  • Hoshizaki KM-650MRH - page 16

    16 Control Boar d P ar t Number 2A1410-01 (f actor y); 2A1410-02 (service) T ype HOS-001A (Control Products - 10 Pin) Contr ol Pr oducts "E" Contr ol Boar d 1. Control Boar d La y out Output T est Switch (used to test rela ys on board) Connector K3 Har v est Control (thermistor) Connector K4 Open (not connected) Microprocessor (board re v ...

  • Hoshizaki KM-650MRH - page 17

    17 2. Features a) Maximum W ater Supply P eriod – 6 minutes Inlet water v alve opening, in the harvest cycle , is limited by the harvest timer . The water v alv e cannot remain open longer than the maximum period. The w ater v alv e can close in less than six minutes if the harvest cycle is completed. b) Harvest Backup Timer and Freeze Timer The ...

  • Hoshizaki KM-650MRH - page 18

    18 f) LED Lights and A udible Alarm Saf eties The red LED indicates proper control v oltage and will remain on unless a control v oltage problem occurs . At star tup a 5 second delay occurs while the board conducts an internal timer check. A shor t beep occurs when the power s witch is tur ned OFF . The green LEDs 1 through 4 energiz e and sequence ...

  • Hoshizaki KM-650MRH - page 19

    19 3. Controls and Adjustments a) Default Dip Switch Settings The dip s witch is f actor y-adjusted to the follo wing positions: Dip Switch No . 1 2 3 4 5 6 7 8 9 10 KM-650MAH OFF OFF OFF OFF ON ON OFF OFF OFF OFF KM-650MWH OFF OFF OFF OFF ON ON OFF OFF OFF OFF KM-650MRH OFF OFF OFF OFF ON ON OFF OFF ON OFF F reeze Timer (9 & 10) Pump-Out F req ...

  • Hoshizaki KM-650MRH - page 20

    20 c) Harvest Timer (dip switch 1 & 2) The har v est timer star ts counting when the ther mistor reads 48°F (9°C) at the e v aporator outlet. No adjustment is required under nor mal use, as the harvest timer is adjusted to the suitable position. How e ver , a setting longer than the factory setting may be advised in cases where the flush pro ...

  • Hoshizaki KM-650MRH - page 21

    21 e) Pump-Out Frequency Contr ol (dip s witch 5 & 6) The pump motor drains the w ater tank at the frequency set b y the pump-out frequency control. The pump-out frequency control is f actor y-adjusted to drain the w ater tank e very 10 cycles, and no adjustment is required. How e v er , where water quality is bad and the icemaker needs a pump ...

  • Hoshizaki KM-650MRH - page 22

    22 4. Control Boar d Chec k Procedure Bef ore replacing a control board that does not sho w a visible def ect and that you suspect is bad, alwa ys conduct the f ollowing chec k procedure. This procedure will help y ou v erify your diagnosis . 1) Check the dip s witch settings to assure that #3, 4, 7, 8, 9, & 10 are in the f actor y def ault pos ...

  • Hoshizaki KM-650MRH - page 23

    23 III. T echnical Inf ormation A. W ater Cir cuit and Refrigeration Circuit 1. KM-650MAH (air-cooled) ...

  • Hoshizaki KM-650MRH - page 24

    24 2. KM-650MWH (water-cooled) ...

  • Hoshizaki KM-650MRH - page 25

    25 3. KM-650MRH (remote air-cooled) ...

  • Hoshizaki KM-650MRH - page 26

    26 B. Wiring Diagrams 1. KM-650MAH (air-cooled) and KM-650MWH (water -cooled) * Pressure Switch Air-Cooled Model W ater-Cooled Model Cut-out 412± 21 PSIG 384± 21 PSIG Cut-in 327±21 PSIG 284±21 PSIG 0 0 12V * ...

  • Hoshizaki KM-650MRH - page 27

    27 * 2. KM-650MRH (remote air-cooled) * Pressure Switch Cut-out 412± 21 PSIG Cut-in 327±21 PSIG 0 12V ...

  • Hoshizaki KM-650MRH - page 28

    28 C. P erf ormance Data 1. KM-650MAH (air-cooled) PERFORMANCE DATA NO. 06A019 ISSUED: 10/10/2006 ITEM : HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MAH 70/21 589 267 566 257 526 238 80/27 572 259 537 243 490 222 90/32 566 257 512 232 467 212 lbs./day kg./day 100/38 555 252 501 227 426 193 70/21 80/27 90/32 watts 100/38 70/21 257 0.97 214 0.81 19 ...

  • Hoshizaki KM-650MRH - page 29

    29 PERFORMANCE DATA NO. 06A020 ISSUED: 10/10/2006 ITEM : HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MWH 70/21 680 308 675 306 626 284 80/27 676 307 668 303 595 270 90/32 675 306 662 300 598 271 lbs./day kg./day 100/38 651 295 647 294 540 245 70/21 80/27 90/32 watts 100/38 70/21 662 2.51 729 2.76 1173 4.44 80/27 713 2.70 817 3.09 1457 5.52 90/32 ...

  • Hoshizaki KM-650MRH - page 30

    30 3. KM-650MRH (remote air-cooled) PERFORMANCE DATA NO. 06A021 ISSUED: 10/10/2006 ITEM : HOSHIZAKI MODULAR CRESCENT CUBER MODEL: KM-650MRH 70/21 615 279 597 271 556 252 80/27 601 273 574 260 523 237 90/32 597 271 554 251 506 230 lbs./day kg./day 100/38 583 264 543 246 462 210 70/21 80/27 90/32 watts 100/38 70/21 266 1.01 220 0.83 198 0.75 80/27 23 ...

  • Hoshizaki KM-650MRH - page 31

    31 IV . Service Diagnosis A. 10-Minute KM Diagnostic Pr ocedure The 10 minute chec k out procedure is basically a sequence chec k which can be used at unit star t-up or for system diagnosis . Using this check out procedure will allo w y ou to diagnose electrical system and component failures in appro ximately 10 minutes under nor mal operating cond ...

  • Hoshizaki KM-650MRH - page 32

    32 freeze with the float s witch remov ed, replace the board. Note: Nor mal freeze cycle will last 20 to 40 min utes depending on model and conditions. Cycle times and pressures should f ollow perf or mance data provided in this manual. 6) Pump-Out Cycle (10/20 second pump out) – the compressor remains energiz ed, the hot gas v alv e energizes , ...

  • Hoshizaki KM-650MRH - page 33

    33 Prob lem P ossible Cause Remedy [1] The icemaker will not star t. (continued) e) High Pressure Control (continued) 3. Ambient or condenser water temper ature too warm. 3. Reduce temperature. 4. Refrigerant ov ercharged. 4. Recharge. 5. F an not operating. (e xcept water-cooled model) 5. See char t 1.[6] 6. Refrigerant line or components plugged. ...

  • Hoshizaki KM-650MRH - page 34

    34 Prob lem P ossible Cause Remedy [1] The icemaker will not star t. (continued) m) Interlock Switch (Cleaning V alve) 1. OFF position. 1. Mov e to ON position. 2. Bad contacts. 2. Check f or continuity and replace. n) W ash Switch 1. W ASH position. 1. Mov e to ICE position. 2. Bad contacts. 2. Check and replace . [2] W ater continues to be suppli ...

  • Hoshizaki KM-650MRH - page 35

    35 Prob lem P ossible Cause Remedy [5] No water comes from spra y tubes. W ater pump will not star t, or freeze cycle time is too shor t. (continued) c) W ater System (continued) 2. Clogged. 2. Clean. 3. Pump out check v alv e leaking by . 3. Check assemb ly and clean. d) Pump Motor 1. Motor winding opened. 1. Replace. 2. Bearing wor n out. 2. Repl ...

  • Hoshizaki KM-650MRH - page 36

    36 2. Evaporator is Fr ozen Up Prob lem P ossible Cause Remedy [1] F reeze cycle time is too long. a) Float Switch 1. Leads shor t-circuit or def ectiv e s witch. 1. Check and replace . 2. Float does not mov e freely . 2. Clean or replace. b) Inlet Water V alve 1. Diaphragm does not close. 1. Check f or water leaks with icemaker off . c) Control Bo ...

  • Hoshizaki KM-650MRH - page 37

    37 Prob lem P ossible Cause Remedy [3] Other (continued) g) Water Supply Line 1. T oo small; requires 3/8" OD line dedicated per machine. 1. Increase water line size . h) W ater Filter 1. Flow rate too small. 1. Replace with filter that has larger flow r ate. 3. Low Ice Pr oduction Prob lem P ossible Cause Remedy [1] F reeze cycle time is lo ...

  • Hoshizaki KM-650MRH - page 38

    38 Prob lem P ossible Cause Remedy [2] Abnormal noise. (continued) c) Compressor (continued) 2. Mounting pad out of position. 2. Reinstall. d) Refrigerant Lines 1. Rub or touch other lines or surf aces. 1. Replace. [3] Ice in storage bin often melts. a) Drain Line(s) 1. Plugged. 1. Clean. b) Icemaker and Bin 1. Dr ains not run separately . 1. Separ ...

  • Hoshizaki KM-650MRH - page 39

    39 V . Remo v al and Replacement of Components IMPOR T ANT Ensure all components, f asteners and thumbscrews are securely in place after the equipment is ser viced. IMPOR T ANT 1. The P oly ol Ester (POE) oils used in R-404A units can absorb moisture quickly . Theref ore it is impor tant to prev ent moisture from enter ing the system when replacing ...

  • Hoshizaki KM-650MRH - page 40

    40 6) A liquid charge is recommended f or charging an R-404A system. Inv er t the service cylinder and place it on scales. Open the high-side, service manifold v alve . 7) Allow the system to charge with liquid until the proper charge w eight is met. 8) If necessar y , add any remaining charge to the system through the lo w-side. Use a throttling v ...

  • Hoshizaki KM-650MRH - page 41

    41 2) Remov e the panels. 3) Recov er the refr igerant and store it in an appro v ed container . 4) Remov e the ter minal cov er on the compressor and disconnect the compressor wir ing. 5) Remov e the hold-down bolts, w ashers and r ubber grommets . 6) Remov e the discharge and suction pipes. 7) Remov e the compressor . Unpack the ne w compressor p ...

  • Hoshizaki KM-650MRH - page 42

    42 E. Remov al and Replacement of Expansion V alve IMPOR T ANT Sometimes moisture in the refrigeration circuit e xceeds the drier capacity and freezes up at the e xpansion valv e. Alwa ys install a new drier ev er y time the sealed refrigeration system is opened. Do not replace the drier until after all other repair or replacement has been made. 1) ...

  • Hoshizaki KM-650MRH - page 43

    43 F . Remo v al and Replacement of Hot Gas V alve and Line V alve IMPOR T ANT 1. Alwa ys use a copper tube of the same diameter and length when replacing the hot gas lines; otherwise the perf or mance ma y be reduced. 2. Alwa ys install a new drier ev er y time the sealed refr igeration system is opened. Do not replace the dr ier until after all o ...

  • Hoshizaki KM-650MRH - page 44

    44 G. Remov al and Replacement of Evaporator IMPOR T ANT Alwa ys install a new drier e v er y time the sealed refrigeration system is opened. Do not replace the drier until after all other repairs or replacement hav e been made. 1) T ur n off the power supply . 2) Remov e the panels and the top insulation ov er the e vaporator . 3) Recov er the ref ...

  • Hoshizaki KM-650MRH - page 45

    45 7) Remov e the screws and the v alve from the brac ket. 8) Install the new v alve . 9) Remov e the dr ier , then place the new drier in position. 10) Braz e all fittings while purging with nitrogen gas flowing at a pressure of 3 to 4 PSIG. 11) Check f or leaks using nitrogen gas (140 PSIG) and soap bub b les. 12) Ev acuate the system, and char ...

  • Hoshizaki KM-650MRH - page 46

    46 J . Remov al and Replacement of Headmaster (Condensing Pressure Regulator - C.P .R.) - Remote Air-Cooled Model Onl y IMPOR T ANT Alwa ys install a new drier e v er y time the sealed refrigeration system is opened. Do not replace the drier until after all other repair or replacement has been made. 1) T ur n off the power supply . 2) Remov e the p ...

  • Hoshizaki KM-650MRH - page 47

    47 K. Remov al and Replacement of Thermistor IMPOR T ANT 1. F ragile , handle v er y carefully . 2. Alwa ys use a recommended sealant (High Ther mal Conductiv e T ype), Model KE4560R TV manuf actured by SHINETSU SILICONE, P ar t Code 60Y000- 11, or P ar t Code 4A0683-01 equiv alent. 3. Alwa ys use a recommended f oam insulation (Non-absorbent T ype ...

  • Hoshizaki KM-650MRH - page 48

    48 3) Remov e the junction box co ver from the remote condenser unit (remote air-cooled model). 4) Remov e the closed end connectors from the fan motor leads . 5) Remov e the fan motor br ac ket and f an motor . 6) Install the new f an motor and replace the remov ed par ts in the re verse order of which they w ere remo v ed. 7) Replace the panels i ...

  • Hoshizaki KM-650MRH - page 49

    49 9) Remov e the screw attaching the pump motor to the pump motor brac ket. 10) Remov e the screws attaching the pump housing to the pump motor . Remov e the housing and check the impeller . 11) If the impeller is def ectiv e , install a new impeller . 12) Install the new motor or ne w par ts , and replace the remo v ed par ts in the re v erse ord ...

  • Hoshizaki KM-650MRH - page 50

    50 VI. Cleaning and Maintenance Instructions IMPOR T ANT Ensure all components, f asteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. A. Cleaning and Sanitizing Procedures W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year . More frequent cleaning, how e v er , ma y be req ...

  • Hoshizaki KM-650MRH - page 51

    51 1. Cleaning Procedure 1) Dilute appro ximately 16 fl. oz. of the recommended cleaner Hoshizaki "Scale A wa y" or "LIME-A-W A Y" (Economics Laborator y , Inc.) with 3 gal. (11 l) of water . 2) Remov e all ice from the ev aporator and the storage bin. Note: T o remov e cubes on the e v aporator , tur n off the power supply and ...

  • Hoshizaki KM-650MRH - page 52

    52 20) Remov e the front panel and fully open the cleaning valv e. 21) Mov e the control switch to the "W ASH" position. 22) Replace the front panel in its correct position. 23) T ur n on the power supply to rinse off the cleaning solution. 24) T ur n off the power supply after 5 min utes. 25) Remov e the front panel. 26) Remov e one end ...

  • Hoshizaki KM-650MRH - page 53

    53 damp cloth containing a neutral cleaner to wipe off oil or dir t build up . 2. Storage Bin and Scoop • W ash y our hands bef ore remo ving ice. Use the plastic scoop provided (bin accessory). • The storage bin is f or ice use only . Do not store anything else in the bin. • K eep the scoop clean. Clean it by using a neutr al cleaner and rin ...

  • Hoshizaki KM-650MRH - page 54

    54 10) Blow the w ater-cooled condenser out, using compressed air or carbon dio xide until water stops coming out. 2. Drain the potable water supply line: 1) Remov e the front panel. 2) Mov e the control switch on the control bo x to the "OFF" position. 3) W ait 3 minutes . 4) Close the potable w ater supply line shut-off valv e and open ...

Manufacturer Hoshizaki Category Ice Maker

Documents that we receive from a manufacturer of a Hoshizaki KM-650MRH can be divided into several groups. They are, among others:
- Hoshizaki technical drawings
- KM-650MRH manuals
- Hoshizaki product data sheets
- information booklets
- or energy labels Hoshizaki KM-650MRH
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hoshizaki KM-650MRH.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hoshizaki KM-650MRH, service manual, brief instructions and user manuals Hoshizaki KM-650MRH. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hoshizaki KM-650MRH.

Similar manuals

A complete manual for the device Hoshizaki KM-650MRH, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hoshizaki KM-650MRH by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hoshizaki KM-650MRH.

A complete Hoshizaki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hoshizaki KM-650MRH - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hoshizaki KM-650MRH, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hoshizaki KM-650MRH, that we can find in the current document
3. Tips how to use the basic functions of the device Hoshizaki KM-650MRH - which should help us in our first steps of using Hoshizaki KM-650MRH
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hoshizaki KM-650MRH
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hoshizaki KM-650MRH in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hoshizaki KM-650MRH?

Use the form below

If you did not solve your problem by using a manual Hoshizaki KM-650MRH, ask a question using the form below. If a user had a similar problem with Hoshizaki KM-650MRH it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)