English dropdown-ico

Manual Q-Logic IS0054604-00 A

80 pages 7.63 mb
Download

Go to site of 80

Summary
  • Q-Logic IS0054604-00 A - page 1

    IS0054604-00 A User ’ s Guide IOCTL to Open-iSCSI Interface QLogic 4000 Series iSCSI Adapters and 8200 Series Converged Network Adapters ...

  • Q-Logic IS0054604-00 A - page 2

    ii IS0054604-00 A User ’s Gu ide—IOCTL to Open- iSCSI Interf ace QLogic 4000 Series iSCSI Adapters and 820 0 Series Converged Networ k Adapters Information fu rnished in this manual is believe d to be accurate and reliable. However , QLogic Corporation assumes no responsibility for its use, nor for any infringements of patent s or other right s ...

  • Q-Logic IS0054604-00 A - page 3

    IS0054604-00 A iii T able of Content s Preface What is in This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Q-Logic IS0054604-00 A - page 4

    iv IS0054604-00 A User ’s Gu ide—IOCTL to Open-iSCSI Interfac e QLogic 4000 Series iSCSI Adapters and 820 0 Series Converged Networ k Adapters Boot T arget Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Default Behavior on RHEL 6.2 . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Default Behavio ...

  • Q-Logic IS0054604-00 A - page 5

    IS0054604-00 A v User ’s Guide—IOCTL to Open-iSCSI Interface QLogic 4000 Series iSCSI Adapter s and 8200 Series Conver ged Network Adap ters 1-5 Open-iSCSI T arget Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 1-6 IOCTL Session Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Q-Logic IS0054604-00 A - page 6

    vi IS0054604-00 A User ’s Gu ide—IOCTL to Open-iSCSI Interfac e QLogic 4000 Series iSCSI Adapters and 820 0 Series Converged Networ k Adapters 2-41 Selecting the Installation T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 2-42 Installation in Progre ss . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Q-Logic IS0054604-00 A - page 7

    IS0054604-00 A vii Preface S tarting with Red Hat ® Enterprise Linux ® (RHEL™) 6 .2 and Novell ® SUSE ® Linux Enterprise Server (SLES ® ) 1 1 SP2, the QLogic qla4xxx driver (iSCSI driver for Linux) supports the Open-iSCSI tool iscsiadm . As a result, iscsiadm can now be used to perform managemen t func tions (configuring network settings, ma ...

  • Q-Logic IS0054604-00 A - page 8

    Preface Related Materials viii IS0054604-00 A Related Materials For additional informat ion, refer to the following:  T echnical Note, 2.10. Kernel http://docs.redhat.com/docs/en-US/Red_Hat_Enterprise_L inux/6/html/6.2_T echnical_Notes/kernel_issues.html  Release Notes for SUSE Linux Enterp rise Server 1 1 Service Pack 2 http://www .novell.co ...

  • Q-Logic IS0054604-00 A - page 9

    Preface T echnical Support IS0054604-00 A ix  Te x t i n ital ics indicates terms, emphasis, va riables, or d ocument titles:  For a complete listing of license agreement s, refer to the QLogic Software End User License Agreement .  What are shortcut keys ?  T o enter the date type mm/dd/yyyy (where mm is the month, dd is the day , and ...

  • Q-Logic IS0054604-00 A - page 10

    Preface T echnical Support x IS0054604-00 A T raining QLogic Global T raining maintains a W eb site at www .qlogictraining.com offering online and instructor-led trainin g for all QLogic products . In addition, sales and technical professionals may obta in Associate and S pecialist -level certifications to qualify for additional benefit s from QLog ...

  • Q-Logic IS0054604-00 A - page 11

    IS0054604-00 A 1-1 1 Legacy vs. Open-iSCSI This section describes the major dif ferenc es between the legacy driver which has an IOCTL-based interface for user space app lication communications, and the Open-iSCSI model. This section includes the following top ics:  “Summary of Major Differe nces” on page 1-2  “Functional Flows” on pa ...

  • Q-Logic IS0054604-00 A - page 12

    1–Legacy vs. Open-iSCSI Summary of Major Dif ferences 1-2 IS0054604-00 A Summary of Major Differences T able 1-1 summarizes the major dif ferences between the legacy IOCTL-based and Open-iSCSI models. T able 1-1. Differences Between IOCTL and Open -iSCSI Driver Models Serial No. Feature IOCTL-based Driver Open-iSCSI-based Driver Re marks 1 Firmwa ...

  • Q-Logic IS0054604-00 A - page 13

    1–Legacy vs . Open-iSCSI Summary of Ma jor Dif ferences IS0054604-00 A 1-3 3 Boot T arget During driver load, the firmware performs auto discovery and login to the boot ta rgets based on the target informatio n saved in the Flash, and posts an AEN to inform the driver of the tar gets and th eir login status. Login to boot targ ets is trig- gered ...

  • Q-Logic IS0054604-00 A - page 14

    1–Legacy vs. Open-iSCSI Summary of Major Dif ferences 1-4 IS0054604-00 A 6 How to view sessions logged in Qlogic applicat ion a Use the following command: iscsiadm -m session 7 T arget scan- ning Login and t arget scanning is done in kernel sp ace as follows: 1. When the driver receives an AEN for the DDB indicating that the target is logged in, ...

  • Q-Logic IS0054604-00 A - page 15

    1–Legacy vs . Open-iSCSI Summary of Ma jor Dif ferences IS0054604-00 A 1-5 9 Dynamic map- ping/unmap- ping of LUNs added to the back-end stor- age The driver handles the following check condi- tion/sense dat a: UNIT_A TTENTION ASC/ASCQ : 0x3F/0x0E to figure out that a new LUN has been adde d on the back-end sto rage and makes an upcall to the SCS ...

  • Q-Logic IS0054604-00 A - page 16

    1–Legacy vs. Open-iSCSI Summary of Major Dif ferences 1-6 IS0054604-00 A 12 Flash DDBs with Open-iSCSI model driver Not applicable The Open -iSCSI driver will support existing Flash DDB entries in the adapter . iscsiadm has no control over these sessions. Session manageme nt of Flash DDB entries is done by the driver itself. Note: iscsiadm is not ...

  • Q-Logic IS0054604-00 A - page 17

    1–Legacy vs . Open-iSCSI Functional Flows IS0054604-00 A 1-7 Functional Flows This section provides functional flow diagr ams for discovery , target login, an d session recovery . 13 CHAP CHAP settings are applied using the QLogic application a . With CHAP support in iscsiadm , CHAP entries can now be added, deleted, and listed from the user spac ...

  • Q-Logic IS0054604-00 A - page 18

    1–Legacy vs. Open-iSCSI Functional Flows 1-8 IS0054604-00 A Discovery Figures 1-1 through 1-3 provide functional flow diagra ms of the disco very process for IOCTL and Open-iSCSI. Figure 1-1. Noninteractive Di scovery in IOCTL Mode (Legacy) Figure 1-2. Interactive Disco very in IOCTL Mode (Legacy) ...

  • Q-Logic IS0054604-00 A - page 19

    1–Legacy vs . Open-iSCSI Functional Flows IS0054604-00 A 1-9 Figure 1-3. Open-iSCSI Discovery ...

  • Q-Logic IS0054604-00 A - page 20

    1–Legacy vs. Open-iSCSI Functional Flows 1-10 IS0054604-00 A T arget Login Figures 1-4 through 1-5 provide functional flow diagrams of the targ et login process for IOCTL and Open-iSCSI. Figure 1-4. IOCTL iSCSI T arget Login Figure 1-5. Open-iSCSI T arget Login ...

  • Q-Logic IS0054604-00 A - page 21

    1–Legacy vs . Open-iSCSI Functional Flows IS0054604-00 A 1-1 1 Session Recovery Figures 1-6 through 1-7 provide functional flow diagrams of the session recovery process for IOCTL and Open-iSCSI. Figure 1-6. IOCTL Session Recovery ...

  • Q-Logic IS0054604-00 A - page 22

    1–Legacy vs. Open-iSCSI Functional Flows 1-12 IS0054604-00 A Figure 1-7. Open-iSCSI Session Recovery ...

  • Q-Logic IS0054604-00 A - page 23

    1–Legacy vs . Open-iSCSI S tate T ransition Diagrams IS0054604-00 A 1-13 S t ate T ransition Diagrams Figures 1-8 through 1-9 provide st ate transition diagrams for IOCTL and Open-iSCSI. These diagrams illustrate the management of the session/t arget life cycle. Figure 1-8. IOCTL S tate T ransition Diagram ...

  • Q-Logic IS0054604-00 A - page 24

    1–Legacy vs. Open-iSCSI S tate T ransition Diagrams 1-14 IS0054604-00 A Figure 1-9. Open-iSCSI S tate T ransition Diagram ...

  • Q-Logic IS0054604-00 A - page 25

    IS0054604-00 A 2-1 2 Boot from SAN This section provides information on c onfigurin g Boot from SAN (BFS) when migrating to the Open-iSCSI model. This section includes the following top ics:  “New Parameter: ql4disablesysfsboot” on p age 2-2  “Boot from SAN Configuration Matrix” on page 2-2  “Configuring Boot from SAN” on pag e ...

  • Q-Logic IS0054604-00 A - page 26

    2–Boot from SAN New Parameter: ql4disablesysfsboot 2-2 IS0054604-00 A New Parameter: ql4disablesysfsboot The ql4disablesysfsboot p arameter is a new driver module parameter for the Open-iSCSI based driver model (it is not supported by the ioctl based driver). This parame ter controls the behavior of boot target login in the Open-iSCSI base driver ...

  • Q-Logic IS0054604-00 A - page 27

    2–Boot from SAN Boot from SAN Configuration Matrix IS0054604-00 A 2-3 T able 2-1. Boot from SAN Configuration Matrix ql4xdisablesysfsboot = 0 ql4xdisablesysfsboot = 1 Boot T arget as send target (ST) Boot T arget as Normal t arget (NT) Boot T arget as send target (ST) Boot T arget as Normal target (NT) Export boot t arget through sysfs (/sys/firm ...

  • Q-Logic IS0054604-00 A - page 28

    2–Boot from SAN Configuring Bo ot from SAN 2-4 IS0054604-00 A Configuring Boot from SAN Boot from SAN Inst allation on SLES 1 1 SP2 and RHEL 6.2 T o configure the adapter for BFS on SLES 1 1 SP2 or RHEL 6.2, follow these steps: 1. While the system is booting up, pre ss CTRL+Q to enter Fast!UTIL on the iSCSI BIOS banner , as shown in Figure 2-1 . ...

  • Q-Logic IS0054604-00 A - page 29

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-5 2. Once in, select the port to be configured, a s shown in Figure 2-2 . Figure 2-2. Selecting the Port to Be Configured 3. Select Configuration Settings , as shown in Figure 2-3 . Figure 2-3. Fast!UTIL Options Me nu—Selecting Configuration Settings ...

  • Q-Logic IS0054604-00 A - page 30

    2–Boot from SAN Configuring Bo ot from SAN 2-6 IS0054604-00 A 4. Select Host Adapter Settings , as shown in Figure 2-4 . Figure 2-4. Selecting the Ho st Adapter Settings Option 5. Select the Initiator IP Settings field, as shown in Figure 2-5 . Figure 2-5. Selecting th e Initiator IP Settings ...

  • Q-Logic IS0054604-00 A - page 31

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-7 6. Provide the initiator IP address, as shown in Figure 2-6 . Figure 2-6. Providing th e Initiator IP Address 7. Press ESC repeatedly until the screen shown in Figure 2-7 appears. Then, select the iSCSI Boot Settings option. Figure 2-7. Configur ation Settings Menu ...

  • Q-Logic IS0054604-00 A - page 32

    2–Boot from SAN Configuring Bo ot from SAN 2-8 IS0054604-00 A 8. Select Primary Boot Device Settings, as shown in Figure 2-8 . Figure 2-8. Select ing Primary Boot Device Settings 9. Provide the target I P address, as shown in Figure 2-9 . Figure 2-9. Providing T arget IP Address for Primary Boot Device ...

  • Q-Logic IS0054604-00 A - page 33

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-9 10. Select Alternate Boot Devi ce Settings, as shown in Figure 2-10 . Figure 2-10. Selecting Alternate Boot Device Settings 1 1. Provide the t arget IP address, as shown in Figure 2-1 1 . Figure 2-1 1. Providing T arget IP Address for Alternate Boot Device ...

  • Q-Logic IS0054604-00 A - page 34

    2–Boot from SAN Configuring Bo ot from SAN 2-10 IS0054604-00 A 12. Press ESC until the menu in Figure 2-12 appears. Select Reinit Adapter to save all IP setti ngs. Figure 2-12. Fast!UTIL Options 13. In iSCSI Boot Settings, select Primary (LUN), as shown in Figure 2-13 . Figure 2-13. Selecti ng the Primary LUN ...

  • Q-Logic IS0054604-00 A - page 35

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-1 1 14. A list of the port’ s devices is displayed, as shown in Figure 2-14 . Select the device to be used as the boot device and press ENTER. Figure 2-14. List of Devices on the Port 15. Repeat step s 13 – 14 to edit the alternate b oot device setting, as in Figure 2-15 . Figure 2-15 ...

  • Q-Logic IS0054604-00 A - page 36

    2–Boot from SAN Configuring Bo ot from SAN 2-12 IS0054604-00 A 16. Change the ad apter ’s boot mode to Manual , as Figure 2-16 shows. Figure 2-16. Setting the Boot Mode to Manual 17. Save the settings for the port. 18. Repeat steps 2 – 14 , but select the second port, a nd configure the boot target s on the port. 19. Save the settings and reb ...

  • Q-Logic IS0054604-00 A - page 37

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-13 Boot from SAN Inst allation on SLES 1 1 SP2 T o configure the adapter for BFS on SLES 1 1 SP2, follow these steps: 1. Boot from the SLES 1 1 SP2 DVD, as shown in Figu re 2-17 . Figure 2-17. Ente ring the Boot BIOS 2. Provide the withiscsi=1 boot option , as shown in Figure 2-18 . Figur ...

  • Q-Logic IS0054604-00 A - page 38

    2–Boot from SAN Configuring Bo ot from SAN 2-14 IS0054604-00 A 3. The Welcome screen appears, as shown in Figure 2-19 . F ollow the instructions on this screen to begin the inst allation. Figure 2-19. Installation Welcome Screen 4. Complete the installatio n by following the instructions on all subsequent screens, as shown in Figures 2-2 0 throug ...

  • Q-Logic IS0054604-00 A - page 39

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-15 Figure 2-21. iSCSI Initiator Overview Figure 2-22. Selecting System Probing ...

  • Q-Logic IS0054604-00 A - page 40

    2–Boot from SAN Configuring Bo ot from SAN 2-16 IS0054604-00 A Figure 2-23. Selecting the Installation Mode Figure 2-24. Setting th e Clock and T ime Zone ...

  • Q-Logic IS0054604-00 A - page 41

    2–Boot from SAN Configuring Boot from SAN IS0054604-00 A 2-17 Figure 2-25. Selecting th e Server Base Scenario Figure 2-26. Preparing the Hard Disk ...

  • Q-Logic IS0054604-00 A - page 42

    2–Boot from SAN Configuring Bo ot from SAN 2-18 IS0054604-00 A Figure 2-27. Performi ng the Installation 5. When the inst allation is completed, reboot the syste m and boot from the iSCSI adapter . ...

  • Q-Logic IS0054604-00 A - page 43

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-19 Configuring Boot from SAN on RHEL 6.2 Inst alling RHEL 6.2 T o install RHEL 6. 2, follow these steps: 1. Boot from the inst allation media, as shown in Figure 2-28 . Figure 2-28. Booting From the Installation Media 2. Choose either to test the media disk or skip the test, a ...

  • Q-Logic IS0054604-00 A - page 44

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-20 IS0054604-00 A 3. Select the network interface through wh ich the inst allation is to be done, as Figure 2-30 shows. Figure 2-30. Selecting Networ k Interface for Installation 4. Configure the IP address eith er st atically or using, as Figure 2-31 shows. Figure 2-31. Configuring the IP A ...

  • Q-Logic IS0054604-00 A - page 45

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-21 5. Once the network interface is configured, the inst allation starts, as shown in Figure 2-32 . Figure 2-32. Start of RHEL 6.2 Installation ...

  • Q-Logic IS0054604-00 A - page 46

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-22 IS0054604-00 A 6. Select the language to use during the inst allation, as shown in Figure 2-33 . Figure 2-33. Selecting the La nguage for the Installation ...

  • Q-Logic IS0054604-00 A - page 47

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-23 7. Select the type of keyboard that is con nected to your system, as shown in Figure 2-34 . Figure 2-34. Selecting the Keyboard ...

  • Q-Logic IS0054604-00 A - page 48

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-24 IS0054604-00 A 8. Select one the two options shown in Fig ure 2-35 : Basic Storage Devices or Specialized S torage Devices . Y ou may select either option since the LUN has been added in the ad apter ’s BI OS. Figure 2-35. Selecti ng S t orage Device T ype ...

  • Q-Logic IS0054604-00 A - page 49

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-25 9. Select the disk that was added in the adap ter ’s BIOS and verify that it ha s two paths to it, as sho wn in Figure 2-36 . Figure 2-36. V erifying Paths to the Disk ...

  • Q-Logic IS0054604-00 A - page 50

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-26 IS0054604-00 A 10. Enter the host name, a s shown in Figure 2-37 . Figure 2-37. Specifyi ng the Host Name ...

  • Q-Logic IS0054604-00 A - page 51

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-27 1 1. Select the time zone, as shown in Figure 2-38 . Figure 2-38. Selecting the Time Zone ...

  • Q-Logic IS0054604-00 A - page 52

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-28 IS0054604-00 A 12. Enter the root credentials t hat you want to set for the system, as shown in Figure 2-39 . Figure 2-39. Entering the Root Credentials ...

  • Q-Logic IS0054604-00 A - page 53

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-29 13. Select the type of p artition layout you want, as shown in Figure 2-40 . Figure 2-40. Selecting th e Partition Layout T ype ...

  • Q-Logic IS0054604-00 A - page 54

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-30 IS0054604-00 A 14. Select the type of inst allation, as shown in Figure 2-41 . Figure 2-41. Selecting the Installation T ype ...

  • Q-Logic IS0054604-00 A - page 55

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 IS0054604-00 A 2-31 15. The installer creates the p artitions on the disk and begins to cop y files to it, as show n in Figure 2-42 . Figure 2-42. Installation in Progress ...

  • Q-Logic IS0054604-00 A - page 56

    2–Boot from SAN Configuring Boot from SAN on RHEL 6.2 2-32 IS0054604-00 A 16. Once the files have been copied, the inst aller will prompt you to reboot the machine, as shown in Figure 2-42 . Figure 2-43. Installation Completed ...

  • Q-Logic IS0054604-00 A - page 57

    2–Boot from SAN ql4xdisablesysfsboot Settin gs and Adapter Boot Mode IS0054604-00 A 2-33 ql4xdisablesysfsboot Settings and Adapter Boot Mode This section demonstrates the effect of the ql4xdisablesysf sboot parameter under differen t adapter boot modes. # iscsiadm -m iface -I qla4xxx.00:c0:dd:07:59:f2.ipv4.0 -n iface.ipaddress -v 10.0.10.183 -o u ...

  • Q-Logic IS0054604-00 A - page 58

    2–Boot from SAN ql4xdisablesysfsboot Settings and Adap ter Boot Mode 2-34 IS0054604-00 A 2 Non-Boot from SAN a No target info is in the firm- ware 1 or 0 Disable Use iscsiadm for discov- ery and login to targets. The correct qla4xxx iface must be used. Discovery: # iscsiadm -m discovery -t st -p <target IP> -I <qla4xxx iface> Login: # ...

  • Q-Logic IS0054604-00 A - page 59

    IS0054604-00 A 3-1 3 Open-iSCSI User ’ s Guide This section provides a User’s Guide for Open-iSCSI. It inclu des the following topics:  “Open-iSCSI Supported Features” on p age 3-2  “Managing QLogic iSCSI Adapters Using iscsiadm” on page 3-4  “Features Not Supported” on p age 3-17  “Migrating to Open-iSCSI Driver” on ...

  • Q-Logic IS0054604-00 A - page 60

    3–Open-iSCSI User ’s Guide Open-iSCSI Supported Features 3-2 IS0054604-00 A Open-iSCSI Supported Features Open-iSCSI support has been added to the QLogic iSCSI driver in Red Hat Enterprise Linux 6.2 and SUSE Linux Enterprise Server 1 1 Service Pack 2. Open-iSCSI infrastructure support s discovery , login to and logout from iSCSI target s, and m ...

  • Q-Logic IS0054604-00 A - page 61

    3–Open-iSCSI User’s Guide Open-iSCSI Supported Features IS0054604-00 A 3-3 Default Behavior on SLES 1 1 SP2 Open-iSCSI is enabled by default on SLES 1 1 SP2 and lo gin to boot targ ets is triggered by iscsiadm during insta llation. The default behavior can be chang ed by setting the driver p arameter ql4xdisablesysfsboot to 1, in which case the ...

  • Q-Logic IS0054604-00 A - page 62

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-4 IS0054604-00 A Managing QLogic iSCSI Adapters Using iscsiadm iSCSI Configuration Files and Persistent Dat abases The Open-iSCSI daemon iscsid can be con figured to use the default node configuration and persistent dat abase to autom atically start discovery on st artup ...

  • Q-Logic IS0054604-00 A - page 63

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-5 2. Discover the iSCSI target. 3. List all discovered target s. 4. Log in to all discovered t argets. 5. List all sessions. # iscsiadm -m discovery -t st -p 192.16 8.1.11 -I qla4xxx.00:0e:1e:05:38:42.ipv4.0 192.168.1.11:3260,1 iqn.1992-04.com.emc:cx.ckm00 ...

  • Q-Logic IS0054604-00 A - page 64

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-6 IS0054604-00 A iSCSI Interface Configuration iSCSI Configuration Parameters Each iSCSI Host Bus Adapter , NIC, or network interface to which sessions a re bound should have its o wn iSCSI interface config file in /etc/ iscsi/ifaces . For hardware of fload iSCSI, iscsia ...

  • Q-Logic IS0054604-00 A - page 65

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-7 Example: IPv4 sample config file with st atic IP address List All ifaces # iscsiadm -m iface Example : # BEGIN RECORD 2.0-872 iface.iscsi_ifacename = qla4xxx-3 iface.ipaddress = 192.168.1.75 iface.hwaddress = 00:0e:1e:04:93:92 iface.transport_name = qla4 ...

  • Q-Logic IS0054604-00 A - page 66

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-8 IS0054604-00 A Display iface Configuration Det ails # iscsiadm -m iface -I <iface_name> Example: Create an iface # iscsiadm -m iface -I <iface_name> -o new # iscsiadm -m iface -I qla4xxx.00:c0:dd:0b:13:f1.ipv4.0 # BEGIN RECORD 2.0-872.28.el6-1031 iface.iscs ...

  • Q-Logic IS0054604-00 A - page 67

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-9 Example: Up date iface Network Parameters # iscsiadm -m iface -I <iface_name> -o update -n <rec_ name> -v <value> # iscsiadm -m iface -I <iface_name> -o apply # iscsiadm -m iface -I <iface_name> -o applyall Where: update upd ...

  • Q-Logic IS0054604-00 A - page 68

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-10 IS0054604-00 A Example: IPv4 Settings (sta tic) Example: IPv4 Settings (DHCP) Example: IPv6 Settings (manual) Example: IPv6 Settings (neighbor disco very) # iscsiadm -m iface -I qla4xxx.00:c0:dd:0b:13:f1.ipv4.0 -o update -n iface.ipaddress -v 192.168.2.214 qla4xxx.00: ...

  • Q-Logic IS0054604-00 A - page 69

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-1 1 Unidirectional and Bidi rectional CHAP settings Example: Display changes made to the 192 .168.1.84:3260 CHAP settings: NOTE The target should be logged out before updating the network p arameters. iscsiadm will give the following warning if a network p ...

  • Q-Logic IS0054604-00 A - page 70

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-12 IS0054604-00 A T arget Discovery Discover T arget s using sendt arget # iscsiadm -m discovery -t st -p <target_ip:target_port> -I <iface_name> -o new, delete, update, nonpersistent In discovery mode, iscsiadm will use the iscsid.conf discovery settings and ...

  • Q-Logic IS0054604-00 A - page 71

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-13 Adding a New discoverydb for send target # iscsiadm -m discoverydb -t st -p 192.168.2.105 -I qla4xxx-3 -o new New discovery record for [192.168.2.105,3260] added. # cat /var/lib/iscsi/send_targets/192.168.2.105,3260/st_config # BEGIN RECORD 2.0-872.28.e ...

  • Q-Logic IS0054604-00 A - page 72

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-14 IS0054604-00 A Remove send target Node # iscsiadm -m discoverydb -t st -p <target IP> -I <iface> -o delete Example: # iscsiadm -m discoverydb -t st -p 192.168.2.105 -I qla4xxx-3 -o delete Adding and Deleting T arget s Adding a New T arget # iscsiadm -m nod ...

  • Q-Logic IS0054604-00 A - page 73

    3–Open-iSCSI User’s Guide Managing QLogic iSCSI Adap ters Using iscsiadm IS0054604-00 A 3-15 List All T arget s # iscsiadm -m node Example: Deleting a T arget Node # iscsiadm -m node -T <target name> -p <target portal> -I <iface> -o delete Example: # iscsiadm -m node -T iqn.2001-05.com.equallogic:0-8a0906-2d733fe02-d25000ecd7a ...

  • Q-Logic IS0054604-00 A - page 74

    3–Open-iSCSI User ’s Guide Managing QLogic iSCSI Adapters Using iscsiadm 3-16 IS0054604-00 A Login to All T arget s Not specifying the t arget name, portal, and ifa ce name results in login to all portals on all nodes/target s through each interface specified in the node co nfiguration. # iscsiadm -m node -l T o login to all port als on a node/ ...

  • Q-Logic IS0054604-00 A - page 75

    3–Open-iSCSI User’s Guide Features Not Supported IS0054604-00 A 3-17 Features Not Supported The features below are not supporte d in Red Hat Enterprise Linux 6.2. These features will be supported in Red Hat Enterpr ise Linux 6.3. 1. iSNS 2. Ping Migrating to Open-iSCSI Driver On a system that was successfully upgraded from RHEL 6.1 to RHEL 6 .2 ...

  • Q-Logic IS0054604-00 A - page 76

    3–Open-iSCSI User ’s Guide Linux Open-iSCSI README 3-18 IS0054604-00 A Linux Open-iSCSI README Go to http://www .open-iscsi.org/docs/README for more det ailed information about Linux Open-iSCSI. ...

  • Q-Logic IS0054604-00 A - page 77

    IS0054604-00 A 4-1 4 Known Issues This section lists curre ntly known issues and provides a brief explanation of each issue. QLogic Application Limit a tions  The RHEL 6.2 and SLES 1 1 SP2 inbox drivers do no t support the following QLogic applications:  iscli (SANsurfer iSCSI CLI)  qaucli (QConvergeConsole CLI)  The QLogic iSCSI driver ...

  • Q-Logic IS0054604-00 A - page 78

    4–Known Issue s CHAP Limitations 4-2 IS0054604-00 A ...

  • Q-Logic IS0054604-00 A - page 79

    ...

  • Q-Logic IS0054604-00 A - page 80

    Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Ali so Viejo, CA 92656 949.389.6000 www .qlogic.com International Office s UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | T aiwan © 2012 QLogic Corporation. Specifications ar e subject to change without notice. All ri ghts reserved worldwide. QCo ...

Manufacturer Q-Logic Category Network Card

Documents that we receive from a manufacturer of a Q-Logic IS0054604-00 A can be divided into several groups. They are, among others:
- Q-Logic technical drawings
- IS0054604-00 A manuals
- Q-Logic product data sheets
- information booklets
- or energy labels Q-Logic IS0054604-00 A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Q-Logic IS0054604-00 A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Q-Logic IS0054604-00 A, service manual, brief instructions and user manuals Q-Logic IS0054604-00 A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Q-Logic IS0054604-00 A.

Similar manuals

A complete manual for the device Q-Logic IS0054604-00 A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Q-Logic IS0054604-00 A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Q-Logic IS0054604-00 A.

A complete Q-Logic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Q-Logic IS0054604-00 A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Q-Logic IS0054604-00 A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Q-Logic IS0054604-00 A, that we can find in the current document
3. Tips how to use the basic functions of the device Q-Logic IS0054604-00 A - which should help us in our first steps of using Q-Logic IS0054604-00 A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Q-Logic IS0054604-00 A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Q-Logic IS0054604-00 A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Q-Logic IS0054604-00 A?

Use the form below

If you did not solve your problem by using a manual Q-Logic IS0054604-00 A, ask a question using the form below. If a user had a similar problem with Q-Logic IS0054604-00 A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)