English dropdown-ico

Manual Niles HDLCR

28 pages 4.97 mb
Download

Go to site of 28

Summary
  • Niles HDLCR - page 1

    INST ALLA TION GUIDE HD LCR FOR USE IN MUL TI-CHANNEL MUSIC OR HOME THEA TER SYSTEMS HIGH DEFINITION, LEFT/CENTER/RIGHT CHANNEL, IN-W ALL LOUDSPEAKER ...

  • Niles HDLCR - page 2

    Thank you for choosing the HDLCR High-Definition, Left/Center/Right Channel In-Wall Loudspeaker from Niles. With proper installation and opera tion, you should enjoy years of trouble-free use. Niles manufactures the industry’ s most complete line of custom installation components and accessories for audio/video systems. T o see the complete Nile ...

  • Niles HDLCR - page 3

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI NILES AUDIO CORPORA TION – 1-800-BUY -HIFI INTRODUCTION The Niles HDLCR High-Definition, Left/Center/Right Channel, In-Wall Loudspeaker is expressly designed for superior sonic quality in front-, center -, or rear -channel applica tions. It employs advanced technology components that extract the subtl ...

  • Niles HDLCR - page 4

    2 INST ALLER-SELECT ABLE ACOUSTIC FINE TUNING Using the ba ffle-moun ted TREBL E and B ASS CUT controls , the in staller can de-e mphasize the bas s and/ or tr eble re sponse b y 3 dB a fter ins talling the HDLC R to pr ecisely tone match the sou nd in any room. CTR L/R MODE SWITCH The HDLCR includes a baffle-mounted CTR L/R mode switch to optimi ...

  • Niles HDLCR - page 5

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI 3 Figure 1 . Mounting an HDLCR loudspeaker into an wall. NILES’ HD HIGH-DEFINITION VOICE MA TCHING Ensures compatibility with other Niles HD High-Definition in-wall, on-wall, and ceiling-mount models to accommodate a wide range of system designs. DOLBY ® DIGIT AL READY The HDLCR is specifically desi ...

  • Niles HDLCR - page 6

    TOOLS AND PRECAUTIONS We recommend using the following tools to install a HDLCR loudspeaker: • Electric drill with 1/4- and 1/2-inch drill bits, and a 1-inch flat drill bit (for drilling through studs) • Keyhole or drywall saw • Stiff wire , fish tape , or glow rods (for routing cables) • Phillips screwdriver set • Cable ties • Pencil ? ...

  • Niles HDLCR - page 7

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI LOUDSPEAKER WIRE Use 2-conductor loudspeaker wire when connecting loudspeakers to your receiver or amplifier . For most applications, we recommend using 16- or 18-gauge wire. For wiring runs longer than 80 feet, we recommend 14-gauge wire. The spring-loaded terminals of the HDLCR will accommodate up to ...

  • Niles HDLCR - page 8

    INSULA TING THE W ALL CA VITY For best performance from your speakers, fill the wall cavity behind the speaker with fiberglass insulation (e.g., R-19 un-ba tted insulation). T ry to keep the same amount of insula tion for each speaker , particularly in the same room, for consistent bass response. SPEAKER PLACEMENT NOTE: THE NILES HDLCR LOUDSPEAKE ...

  • Niles HDLCR - page 9

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI As for placement height, place front left and right speakers on either side of the picture source so that their tweeters are not more than 24 inches above or below the center-channel speaker’ s tweeter (see Figure 3 on page 8). NOTE: DO NOT PLACE AN HDLCR SPEAKER TOO CLOSE TO A DIRECT -VIEW TV MONITOR, ...

  • Niles HDLCR - page 10

    PLACING AN HDLCR AS THE CENTER-CHANNEL SPEAKER The center -channel speaker is the workhorse in a home theater system. It handles all of the critical dialog and is vitally important in creating the illusion of sounds emanating directly from the picture. Here are some tips for obtaining optimum center -channel performance: • In a typical installati ...

  • Niles HDLCR - page 11

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI • For installations where a perforated projection screen will be used, place the HDLCR, either horizontally or vertically , behind the screen at ear level, as shown in Figure 4 . INST ALLA TION FUNDAMENT ALS RUNNING THE SPEAKER WIRE IN NEW CONSTRUCTION IMPORT ANT : IF YOU HAVE DOUBTS ABOUT WHETHER YOU ...

  • Niles HDLCR - page 12

    RUNNING THE SPEAKER WIRE IN NEW CONSTRUCTION (CONTINUED) SCHEDULING AND PREP ARA TION Plan to schedule the speaker wiring after the electrical wiring is finished. That way you can a void wire routes, which could potentially induce hum over the speaker wire. The basic wiring rules are: • Never run speaker wire through the same hole as an electric ...

  • Niles HDLCR - page 13

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI • When drilling holes in ceiling joists, drill in the center of the joists and tr y to locate the hole near the end of the joist. IMPORT ANT : DO NO T DRILL THROUGH A GLU-LAM OR LOAD-BEARING BEAM WITHOUT THE DIRECTION OF YOUR CONTRACTOR. • T r y to line the holes up perfectly , because it makes pulli ...

  • Niles HDLCR - page 14

    CONCEALING SPEAKER WIRE (CONTINUED) ABOUT EXTERIOR W ALLS Concealing wires in exterior walls is more complex, since the walls are stuffed with insulation to protect the house from the heat and cold outside. Moreover , our national building code requires that a horizontal stud placed between the vertical studs break the hollow wall space in exterior ...

  • Niles HDLCR - page 15

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI When you don’t have access above or below the wall, try to estimate the existing wire and pipe locations from known positions of electrical outlets and plumbed fixtures on both sides of the wall. T ake a look at the outside of your house too – sometimes conduit, vents, or drainpipe will provide usef ...

  • Niles HDLCR - page 16

    CONCEALING SPEAKER WIRE (CONTINUED) CUTTING HOLES In traditional wood stud/drywall construc- tion, first cut the hole for the speaker . Then, in the opening, use a drill with a long bit to auger a wire route up or down the wall. Next, cut a hole in the dr ywall for stud access, drill holes through the studs, and run your wire, as shown in Figure 9 ...

  • Niles HDLCR - page 17

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI 2. Screw one side of the assembled brack et with wings to the stud or joist, using one of the supplied screws. Level the brack et, and then screw the other side of the bracket/wing assembly to the stud or joist. T wo screws on each side make for a very secure installation. 3. Attach the wire to the brac ...

  • Niles HDLCR - page 18

    EXISTING CONSTRUCTION: INST ALLING A BRACKET IMPORT ANT : BEFORE YOU CUT INTO ANY W ALL, REVIEW THE SECTIONS ON SPEAKER PLACEMENT ON P AGE 6 AND RUNNING THE SPEAKER WIRE IN NEW CONSTR UCTION ON P AGE 9. BE SURE NOT TO DRILL OR CUT THROUGH EXISTING WIRES, PIPES, OR STR UCTURE. IF YOU FEEL ANY EXTRA RESIST ANCE AS YOU ARE DRILLING OR SA WING, STOP! 1 ...

  • Niles HDLCR - page 19

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI FINISHING THE INST ALLA TION P AINTING THE GRILLE AND FRAME After drywall is up, each HDLCR frame and grille may be painted without the need for primer . For best results, use a spray gun or airless sprayer , thin the paint to prevent clogging of the grille holes, and apply several light coats instead of ...

  • Niles HDLCR - page 20

    INST ALLING A NILES MS-100 MICROSENSOR ® 1. For each speaker , locate the half-inch round, molded “IR Sensor Knockout” on the baffle . 2. Lay each speaker face down on a clean carpet or rug . Put the tip of a screwdriver into the center of the round “knockout” and sharply tap the screwdriver handle as necessary . NOTE: TO PREVENT DAMAGE TO ...

  • Niles HDLCR - page 21

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI CONNECTING AND INST ALLING THE SPEAKER 1. At each speaker , separate the speaker wire so that at least 2 inches of each conductor are free . Strip away 1/4 inch of insulation from each speaker wir e. 2. On each set of speaker connectors, press down the spring-loaded lever , insert the ap- propriate condu ...

  • Niles HDLCR - page 22

    CO NNE CTI NG AND INS T AL LIN G TH E S PEA KER (C ONTI NUED ) IMPORT ANT : WHEN INST ALLING THE SPEAKERS IN THE CEILING, OR IF THE INST ALLA TION IS IN AN EARTHQUAKE ZONE, WE RECOMMEND USING THE ENCLOSED SHEET MET AL SCREWS TO SECURE THE BAFFLE TO THE FRAME AS FOLLOWS: a. Locate the dimples on the front baffle . b . Place the self-tapping sheet-me ...

  • Niles HDLCR - page 23

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI 1. Stand halfway between the speakers. 2. Play some music with the amplifier or radio set to Mono . 3. Listen to the richness of the bass and the loudness of the sound. 4. T ur n off the amplifier and reverse the connections on one amplifier channel only . 5. Repeat the listening test with the same volum ...

  • Niles HDLCR - page 24

    ADJUSTING THE TWEETER ( CONT INUE D) 3. Pivot the tweeter on each speaker equally by depressing the housing at the arro ws until the desired angle is achieved, as shown in Figure 20 . INST ALLING THE GRILLE At each speaker , carefully fit the grille into its recess so that it is barely in place. Starting with one corner , gently press the grille a ...

  • Niles HDLCR - page 25

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI REMOVING THE SPEAKER After removi ng the g rille, use tw o small screwdri vers (or needle- nose pli ers) to release the snaps that ho ld the speaker (and baf fle) to t he frame . Insert the scr ewdriver s into t he hole s in the snaps and e xert fo rce stra ight down (towards t he woofe r) until the sn ...

  • Niles HDLCR - page 26

    LIMITED W ARRANTY NILES AUDIO CORPORA TION (“NILES”) W ARRANTS ITS LOUDSPEAKER PRODUCTS TO THE ORIGINAL PURCHASER TO BE FREE OF MANUF ACTURING DEFECTS IN MA TERIAL AND WORKMANSHIP FOR A PERIOD OF FIVE YEARS FROM D A TE OF PURCHASE. THIS WARRANTY IS SUBJECT TO THE FOLLOWING ADDITIONAL CONDITIONS AND LIMIT A TIONS. THE WARRANTY IS VOID AND INAPPL ...

  • Niles HDLCR - page 27

    W ARRANTY REGISTRA TION CARD Model Purchased_________________________________________________________ Serial Number___________________________________________________________ Date Purchased (month/day/year)_____________________________________________ Dealer Name and Location__________________________________________________ _______________________ ...

  • Niles HDLCR - page 28

    Niles Audio Corporation 12331 S.W . 130 Street Miami, Florida 33186 Designed and Engineered in USA Made in China ©2005 Niles Audio Corporation. All rights reserved. Niles, the Niles logos and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. All other trademarks are the property of their re spe cti ve ow ...

Manufacturer Niles Category Home Theater System

Documents that we receive from a manufacturer of a Niles HDLCR can be divided into several groups. They are, among others:
- Niles technical drawings
- HDLCR manuals
- Niles product data sheets
- information booklets
- or energy labels Niles HDLCR
All of them are important, but the most important information from the point of view of use of the device are in the user manual Niles HDLCR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Niles HDLCR, service manual, brief instructions and user manuals Niles HDLCR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Niles HDLCR.

Similar manuals

A complete manual for the device Niles HDLCR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Niles HDLCR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Niles HDLCR.

A complete Niles manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Niles HDLCR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Niles HDLCR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Niles HDLCR, that we can find in the current document
3. Tips how to use the basic functions of the device Niles HDLCR - which should help us in our first steps of using Niles HDLCR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Niles HDLCR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Niles HDLCR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Niles HDLCR?

Use the form below

If you did not solve your problem by using a manual Niles HDLCR, ask a question using the form below. If a user had a similar problem with Niles HDLCR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)