-
Grizzly H2909 - page 1
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN 18 GAUGE STAPLER KIT MODEL H2909 INSTRUCTION MANUAL ...
-
Grizzly H2909 - page 2
For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a ...
-
Grizzly H2909 - page 3
H2909 18 Gauge Stapler Kit -2 - 10. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheat ...
-
Grizzly H2909 - page 4
H2909 18 Gauge Stapler Kit -3 - Operating this stapler can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this stapler discharges at 85-90 decibels. To protect your hearing, alw ...
-
Grizzly H2909 - page 5
H2909 18 Gauge Stapler Kit -4 - INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com W ...
-
Grizzly H2909 - page 6
H2909 18 Gauge Stapler Kit -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the stapler at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the sta- pler to explode, ...
-
Grizzly H2909 - page 7
H2909 18 Gauge Stapler Kit -6 - OPERATION Loading Stapler Depth Adjustment Operating Stapler To load your stapler: 1. Disconnect the air supply from the stapler! 2. Push the magazine latch in the direc- tion shown in Figure 1 . 3. Pull back the magazine cover until it stops. 4. Point the stapler up and insert a stick of staples into the magazine as ...
-
Grizzly H2909 - page 8
H2909 18 Gauge Stapler Kit -7 - To operate your stapler: 1. Connect the air supply to the quick connect fitting. 2. Test the loaded stapler for proper penetration. Hold the stapler perpen- dicular to the surface of a piece of clean scrap wood that is thick enough for the length of staples you have loaded. Depress the safety yoke mechanism on your w ...
-
Grizzly H2909 - page 9
H2909 18 Gauge Stapler Kit -8 - Cleaning Stapler Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the sta- pler; this may result in leaks and damage to the stapler and the air couplings. Never u ...
-
Grizzly H2909 - page 10
H2909 18 Gauge Stapler Kit -9 - Replacing Pistons/O-Rings If you use your stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: LOAD 10 2 03 04 0 50 Figure 6. Removing stapler exhaust cap. 8. With a lo ...
-
Grizzly H2909 - page 11
H2909 18 Gauge Stapler Kit -10 - H2909 PART BREAKDOWN ...
-
Grizzly H2909 - page 12
H2909 18 Gauge Stapler Kit -11 - 01 PH2909001 UM HD BOLT 02 PH2909002 CAP COVER 03 PH2909003 SEAL 04 PH2909004 CAP SCREW 05 PH2909005 SETSCREW 06 PH2909006 CAP 07 PH2909007 PISTON STOPPER 08 PH2909008 O-RING 09 PH2909009 COLLAR 10 PH2909010 O-RING 11 PH2909011 SPRING 12 PH2909012 PISTON HEAD VALVE 13 PH2909013 O-RING 14 PH2909014 O-RING 15 PH290901 ...
-
Grizzly H2909 - page 13
TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips staples while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the stapler. Stapler does not fire. 1. O-rings must be replaced & operation of safety yoke must be ch ...
-
Grizzly H2909 - page 14
H2909 18 Gauge Stapler Kit -13 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole wr ...
-
Grizzly H2909 - page 15
Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # ___________________________ Order # _______________________ The following information i ...
-
Grizzly H2909 - page 16
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
Do you have a question concerning Grizzly H2909?
Use the form below
If you did not solve your problem by using a manual Grizzly H2909, ask a question using the form below. If a user had a similar problem with Grizzly H2909 it is likely that he will want to share the way to solve it.