English dropdown-ico

Manual Makita G12010R

44 pages 1.84 mb
Download

Go to site of 44

Summary
  • Makita G12010R - page 1

    ISSUE EMD-GU2000 PRINTED IN JAPAN October 2004 CE-SK 100 Makita Corporation 3-11-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan 3ZZ9020161 GENERATO R INSTRUCTIONS FOR USE アメリカ ISSUE EMD-GU1539 PRINTED IN JAPAN Makita Corporation 3-1 1-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan 3ZZ9020107 GENERATO R INSTRUCTIONS FOR USE ア メ リ カ ...

  • Makita G12010R - page 2

    The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING : NOTICE FEDERAL EMISSION COMPONENT DEFECT WARRANTY and CALIFORNIA EMISSION CONTROL WARRANTY are applicable to only those engines/ generators complied with EPA (Environmental Protection Agency) ...

  • Makita G12010R - page 3

    FEDERAL EMISSIONS COMPONENT DEFECT W ARRANTY EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applicable in all States, except the State of California Makita U.S.A. Inc., La Mirada, California, (herein "MAKITA") warrant(s) to the initial retail purchaser and each subsequent owner, that this Nonroad engine (herein & ...

  • Makita G12010R - page 4

    *The replacement parts used for required maintenance services. *Consequential damages such as loss of time, inconvenience, loss of use of the engine orequipment, etc. *Diagnosis and inspection charges that do not result in warranty-eligible service being performed. *Any non-authorized replacement part, or malfunction of authorized parts due to use ...

  • Makita G12010R - page 5

    CALIFORNIA EMISSION CONTROL W ARRANTY ST A TEMENT (This warranty does not apply in any other state.) YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The California Air Resources Board and Makita U.S.A., Inc. (herein "MAKIT A") are pleased to explain the emission control warranty on your 2005 and later small off-road engine (herein "engine&quo ...

  • Makita G12010R - page 6

    MAKIT A , a distributor of small off-road equipment in the U.S., warrants to the owner of 2005 and later engines that the engine (1) has been designed, built, and equipped at the time of manufacture so as to conform with the applicable regulations of the California Air Resources Board and, (2) is free from defects in materials and workmanship which ...

  • Makita G12010R - page 7

    WHA T IS NOT COVERED UNDER THIS W ARRANTY This warranty does not cover any emission-related part which malfunctions, fails, or is damaged due to alterations and/or modifications such as changing, adding, or removing parts. When an engine is being serviced under warranty , MAKIT A and any of its authorized dealers, distributors, or warranty stations ...

  • Makita G12010R - page 8

    REP AIR AND REPLACEMENT OF EMISSION-RELA TED P ARTS It is recommended that only engine replacement parts which have been authorized and approved by MAKIT A should be used in the performance of any warranty maintenance or repairs of emission-related parts. These replacement parts will be provided at no charge if the part is still under warranty . HO ...

  • Makita G12010R - page 9

    Thank you for purchasing a Makita generator . This manual covers operation and maintenance of the Makita generators. All information in this publication is based on the latest production information available at the time of approval for printing. Pay special attention to statements preceded by the following words: ■ The generator is designed to g ...

  • Makita G12010R - page 10

    ■ Check that following accessories come with your Makita Generator . (1) Instruction for use (2) Servicing tools (3) Battery mounting bracket (See page 8 and 9.) ■ Be sure to replenish with engine oil. (See page 6 for details.) G12010R排対_GU2000 05.1.20 1:38 PM ページ09 ...

  • Makita G12010R - page 11

    CONTENTS 1. SAFETY PRECAUTIONS ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 1 2. SPECIFICA TIONS ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 4 3. COMPONENTS ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ? ...

  • Makita G12010R - page 12

    − 1 − 1. SAFETY PRECAUTIONS Do not operate the generator near gasoline or gaseous fuel because of the potential danger of explosion or fire. Do not fill the fuel tank with fuel while the engine is running. Do not smoke or use open flame near the fuel tank. Be careful not to spill fuel during refueling. If fuel is spilt, wipe it off and let dry ...

  • Makita G12010R - page 13

    − 2 − Operate the generator on a level surface. It is not necessary to prepare a special foundation for the generator . However , the generator will vibrate on an irregular surface, so choose a level place without surface irregularities. If the generator is tilted or moved during operation, fuel may spill and/ or the generator may tip over , ca ...

  • Makita G12010R - page 14

    − 3 − Engine becomes extremely hot during and for some time after operation. Keep combustible materials well away from generator area. Be very careful not to touch any parts of the hot engine especially the muffler area or serious burns may result. Keep children and all bystanders at a safe distance from work areas. It is absolutely essential t ...

  • Makita G12010R - page 15

    2. SPECIFICA TIONS − 4 − Model G12010R Alternator Type Brush, Self-exciting, 2-pole, Single-phase Rated voltage 120V / 240V 9500 VA A.V.R type Engine Model EH65D Type Twin cylinder, Air-cooled, 4-stroke, Overhead valve engine Displacement 653 cm 3 Fuel Automotive unleaded gasoline Oil capacity 0.41 US-gal (1.55 liters) Starting system Electric ...

  • Makita G12010R - page 16

    3. COMPONENTS − 5 − SPARK PLUG CAP FUEL COCK BATTERY TANK CAP SPARK PLUG CAP OIL FILLER CAP MUFFLER OIL GAUGE CONNECTOR FOR REMOTE CONTROL ELECTRIC STARTER OIL DRAIN PLUG FUEL TANK CONTROL PANEL AIR CLEANER COOLING AIR INLET PORT OIL FILTER G12010R排対_GU2000 05.1.20 1:38 PM ページ5 ...

  • Makita G12010R - page 17

    − 6 − UPPER LEVEL LOWER LEVEL OIL GAUGE Oil gauge Upper level Lower level 4. PRE-OPERA TION CHECK CHECK ENGINE OIL Before checking or refilling oil, be sure generator is located on stable and level surface with engine stopped. 1) Remove oil level gauge and check the engine oil level. 2) If oil level is below the lower level "L" refill ...

  • Makita G12010R - page 18

    1) Check fuel level at fuel level gauge. 2) If fuel level is low , refill with automotive unleaded gasoline only . This engine is certified to operate on automotive unleaded gasoline. 3) Be sure to use the fuel filter screen on the fuel filter neck. Fuel filter screen Tank cap Fuel gauge EMPTY FULL EF − 7 − Do not refuel while smoking or near o ...

  • Makita G12010R - page 19

    − 8 − Make sure you review each warning in order to prevent fire hazard. ■ Do not refill tank while engine is running or hot. ■ Close fuel cock before refueling with fuel. ■ Be careful not to admit dust, dirt, water or other foreign objects into fuel. ■ Do not fill above the top of the fuel filter (marked "LEVEL") or the fuel ...

  • Makita G12010R - page 20

    − 9 − RED CABEL RED CABEL LESS THAN 10.2 in. (260 mm) LESS THAN 6.7 in. (170 mm) LESS THAN 8.1 in. (205 mm) ① Butterfly nut ┓ ② Long bolt ┣ Accessory ③ Supporting arm ┛ parts ④ Terminals and nut ④ ① ③ ② Should the connection be made in incorrect manner , the engine will be broken. ［ CAUTION ］ Death, personal i ...

  • Makita G12010R - page 21

    CHECK COMPONENT P ARTS Check following items before starting engine: ■ Fuel leakage from fuel hose, etc. ■ Bolts and nuts for looseness. ■ Components for damage or breakage. ■ Generator not resting on or against any adjacent wiring. CHECK GENERA T OR SURROUNDINGS − 10 − Make sure you review each warning in order to prevent fire hazard. ...

  • Makita G12010R - page 22

    (1) Make sure that the no-fuse breaker is off. (2) T urn the fuel cock to the vertical (open) position (3) T urn the key switch to the " ST ART " position. If the engine won't start, turn the switch back to "RUN" position and then wait for approximately 10 seconds to try it again. NOTE : ■ Y ou might have to keep the star ...

  • Makita G12010R - page 23

    − 12 − USING ELECTRIC POWER ■ Make sure that the appliance is switched OFF before connecting it to the generator . ■ Do not move the generator while it is running. ■ Be sure to ground the generator if the connected appliance is grounded. Failure to ground unit may lead to electrical shock. W ARNING CONTROL P ANEL KEY SWITCH OIL PURESSURE ...

  • Makita G12010R - page 24

    − 13 − (1) AC APPLICA TION (a) Ground the generator , using the ground terminal located at the side of the panel. (b) Before starting the engine, check that the no-fuse breaker of the generator and the power switches of the appliances are turned off. (c) Connect the plugs of the appliances to the receptacles before starting the engine. If you w ...

  • Makita G12010R - page 25

    − 14 − up to 30A up to 30A up to 20A NEMA 5-20R NEMA L5-30R NEMA L14-30R NEMA 5-20P NEMA L5-30P NEMA L14-30P GFCI (Ground Fault Circuit Interrupter) Receptacle, duplex (REC1) Locking Receptacle (REC2) Locking Receptacle (REC3) Style Ampere Receptacle AC plug Description up to 50A Locking Receptacle (REC4) TABLE 1 ■ Check the amperage of the r ...

  • Makita G12010R - page 26

    − 15 − The duplex 120V receptacle is protected by a GFCI (Ground Fault Circuit Interrupter). GFCI shuts off the output current from the duplex 120V receptacle when a ground fault occurs in the generator or the appliance. Please note that other receptacles are not protected by GFCI. ［ CAUTION ］ GFCI RECEPT ACLE After starting the engine, che ...

  • Makita G12010R - page 27

    − 16 − MAIN POWER LINE TRANSFER SWITCH UTILITY HIGH LINE CONNECTING BOX 240V RECEPTACLE (a) When connecting a Makita generator to a house wiring, generator output power must be taken from the 240V -4P receptacle. (b) Install a transfer switch. A transfer switch must be installed to transfer the load from the commercial power source to the gener ...

  • Makita G12010R - page 28

    − 17 − Utility high line M eter box Generator House circuit breaker XW Y X ( X )( Y ) ( G ) ( W ) WY XW Y Transfer switch 240V 4P- Receptacle 120V appliance 120V appliance 240V appliance OR Generator ( X ) ( Y ) ( G ) ( W ) 240V 4P- Receptacle W X Y (c) Operating the generator . ■ Set the full power switch to 120V/240V side. ■ T urn the hou ...

  • Makita G12010R - page 29

    − 18 − (e) T urn on the switch of the appliance. PILOT LAMP NOTE : When the no-fuse breaker turns off during operation, the generator is over loaded or the appliance is defective. Stop the generator immediately , check the appliance and / or generator for overloading or detect and have repaired as necessary by Makita dealer or service shop. (d) ...

  • Makita G12010R - page 30

    − 19 − (3) IDLE CONTROL SWITCH IDLE CONTROL SWITCH automatically reduces engine speed when load is OFF , and automatically increases engine speed to rated r .p.m. when load is ON. IDLE CONTROL SWITCH provides fuel economy and low noise operation at no- load running. (1) HOW TO USE IDLE CONTROL SWITCH ■ Start the engine with IDLE CONTROL SWITC ...

  • Makita G12010R - page 31

    − 20 − CLOSE CLOSE OPEN (6) Close the fuel cock. STOPPING THE GENERA TOR (1) T urn off the power switch of the electric equipment. (2) T urn the no-fuse breaker to off. (3) Unplug the cord from receptacle of the generator . STOP RUN STOP RUN START START (4) Allow the engine to run at no-load for about 3 minutes to cool down before stopping. (5) ...

  • Makita G12010R - page 32

    6. W A TT AGE INFORMA TION − 21 − Some appliances need a "surge" of energy when starting. This means that the amount of electrical power needed to start the appliance may exceed the amount needed to maintain its use. Electrical appliances and tools normally come with a label indicating voltage, cycles/Hz, amperage (amps) and electrica ...

  • Makita G12010R - page 33

    − 22 − To determine the total wattage required to run a particular electrical appliance or tool, multiply the voltage figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps) information can be found on a name plate which is normally attached to electrical appliances and tools. NOTE : ■ The above wat ...

  • Makita G12010R - page 34

    7. SP ARK ARRESTER − 23 − SP ARK ARRESTER In a dry or wooded area, it is recommendable to use the product with a spark arrester . Some areas require the use of a spark arrester . Please check your local laws and regulations before operating your product . The spark arrester must be cleaned regularly to keep it functioning as designed. A clogged ...

  • Makita G12010R - page 35

    8. MAINTENANCE SCHEDULE − 24 − DAIL Y INSPECTION Before running the generator , check the following service items: Excessive vibration,noise Clean air cleaner element Safe surroundings Enough clean engine oil Leakage of gasoline and engine oil Loose or broken bolts and nuts Enough gasoline PERIODIC MAINTENANCE Periodic maintenance is vital to s ...

  • Makita G12010R - page 36

    − 25 − (Periodic Maintenance Schedule table) *Note 1 : Initial oil change should be performed after first twenty (20) hours of operation. Thereafter change oil every hundred (100) hours. Before changing oil, check for a suitable way to dispose of old oil. Do not pour it down into sewage drains, onto garden soil or into open streams. Y our local ...

  • Makita G12010R - page 37

    9. "HOW -T O" MAINTENANCE − 26 − OIL FILTER ENGINE OIL CHANGE ■ Initial oil change ・・・・・ After 20 hours of operation ■ Thereafter ・・・・・ Every 100 hours of operation 1. When changing oil, stop the engine and loosen the drain plug. 2. Re - install the drain plug before refilling oil. 3. Refer to the recommended o ...

  • Makita G12010R - page 38

    − 27 − ■ Urethane Foam cleaning W ash and clean the urethane foam in kerosene. Saturate in a mixture of 3 parts kerosene and 1 part engine oil, and then squeeze to remove excess oil. Clean or replace the urethane foam element every 50 hours. (more often in dusty environments) ■ Paper element Clean by tapping gently to remove dirt and blow o ...

  • Makita G12010R - page 39

    − 28 − Spark plug NGK BPR5ES (CHAMPION RN11YC) CLEANING FUEL STRAINER Dirt and water in the fuel are removed by the fuel strainer . (a) Remove the strainer cup and throw away water and dirt. (b) Clean the screen and strainer cup with gasoline. (c) T ightly fasten the cup to main body , making sure to avoid fuel leak. (d) Clean the electrodes if ...

  • Makita G12010R - page 40

    − 29 − CHECKING CARBON BRUSH If the brush become excessively worn, its contact pressure with the slip ring changes and causes a roughened surface on the slip ring, resulting in irregular generator performance. Check the brush every 500 hours or if generator performance is irregular . If the brush is 0.2 in.(5 mm) long or less, replace it with a ...

  • Makita G12010R - page 41

    10. PREP ARA TION FOR ST ORAGE − 30 − The following procedures should be followed prior to storage of your generator for a period of 6 months or longer . ■ Drain fuel from fuel tank and strainer (cup) carefully by disconnecting the fuel line. Gasoline left in the fuel tank will eventually deteriorate making engine-starting difficult. ■ In o ...

  • Makita G12010R - page 42

    11 . TROUBLESHOOTING − 31 − When generator engine fails to start after several attempts, or if no electricity is available at the output receptacles, check the possible causes in accordance with the following table. If your generator still fails to start or generate electricity , contact your nearest Makita dealer or authorized service center f ...

  • Makita G12010R - page 43

    12. WIRING DIAGRAM − 32 − Blk/Y 53 2 4 (AC output) ( AVR ) 1 CONTROL BOX Fuel cut Ignition coil Auto choke ( Bimetal ) Electric starter Oil pressure switch Regulator Magnetic switch Charge coil Exciting coil - + Battery 12V Grn/Y Grn LBlu Gry W Key switch to earth terminal ST Relay Connector ( Remote control ) Gry R15 Blk15 Grn W W W Blk/W Gry ...

  • Makita G12010R - page 44

    ISSUE EMD-GU2000 PRINTED IN JAPAN October 2004 CE-SK 100 Makita Corporation 3-11-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan 3ZZ9020161 GENERATO R INSTRUCTIONS FOR USE アメリカ ISSUE EMD-GU1539 PRINTED IN JAPAN Makita Corporation 3-1 1-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan 3ZZ9020107 GENERATO R INSTRUCTIONS FOR USE ア メ リ カ ...

Manufacturer Makita Category Portable Generator

Documents that we receive from a manufacturer of a Makita G12010R can be divided into several groups. They are, among others:
- Makita technical drawings
- G12010R manuals
- Makita product data sheets
- information booklets
- or energy labels Makita G12010R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita G12010R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita G12010R, service manual, brief instructions and user manuals Makita G12010R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita G12010R.

Similar manuals

A complete manual for the device Makita G12010R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita G12010R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita G12010R.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita G12010R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita G12010R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita G12010R, that we can find in the current document
3. Tips how to use the basic functions of the device Makita G12010R - which should help us in our first steps of using Makita G12010R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita G12010R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita G12010R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita G12010R?

Use the form below

If you did not solve your problem by using a manual Makita G12010R, ask a question using the form below. If a user had a similar problem with Makita G12010R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)