-
Makita 4302C - page 1
Electronic Jig Saw 26 mm (1"l MODEL 4302C 219 mm 2 5 ky (8 5/8") (5 5 Ibs) 1,000 3.000 60 mm 10 mm (2 3/8") !3/8"1 INSTRUCTION MANUAL SPEC IF I CAT IONS weight Strokes Overall per minute length Max cuttiny capacities Steel Length of stroke x Manufacturer reserves the right to change specifications without notice * Note Specifica ...
-
Makita 4302C - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 4302C - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 4302C - page 4
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- 2. Don't cut hollow pipe. 3. Do not cut oversize workpiece. 4. Check for the proper clearance beneath the workpiece before cutting so that 5. Hold the tool firmly. 6. Make sure the blade is not contacting the workpiece before the switch is 7 ...
-
Makita 4302C - page 5
Installing Makita jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Use the hex wrench to loosen the bolt. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edqe of the blade J'g saw fits into the ro ...
-
Makita 4302C - page 6
Installing universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.35 mm (1 /4"). I Insert the blade i ...
-
Makita 4302C - page 7
Straight line or orbital cutting action Conventional jig saws cut with a straight line action, that is, the blade moves only up and down in a straight line. Your saw also cuts in this manner but, for softer workpieces, an orbital cutting action can be selected. Soft workpieces like wood and plastic permit deep penetration of indivi- dual saw teeth. ...
-
Makita 4302C - page 8
Speed change To adjust the tool speed, turn the speed change dial while the tool is running under no load. The tool speed can be adjusted between 1,000 and 3,000 strokes per minute. The reference table on the right denotes the relationship between the number set- approximate strokes per minute at that Number 1 2 1 setting. 3 1 4 1 5 1 6 tings on th ...
-
Makita 4302C - page 9
Operation Turn the tool on and wait until the blade attains full speed. Then rest the base flat on the workpiece and gently move the tool forward along the previously marked cut- ting line. When cutting curves, advance the tool very slowly. I CAUTION : Failure to hold the tool base flush with the workpiece may cause blade breakage. Bevel cutting Wi ...
-
Makita 4302C - page 10
Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and the roller, then secure the bolt. Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a "plunge cut". This c ...
-
Makita 4302C - page 11
Using guide rule (Rip fence) When cutting widths of under 150 mm (6") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To attach the guide rule (rip fence), secure the rule holder to the base with the screw (do not tighten). Insert the guide rule between the base and the rule holder. Now tighten the screw with the hex ...
-
Makita 4302C - page 12
To attach the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. Then slide the base of the tool forwards. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coc._rnt (cutting c when cutting metal. Failure t ...
-
Makita 4302C - page 13
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool will stop when the carbon brushes wear to a certain length. When this occurs, both carbon brushes should be replaced. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and repla ...
-
Makita 4302C - page 14
0 Jig saw blade Wood and plywood - Plastics Aluminum Mild steel 1 5 - 3 mm thick 1 - 6 mm thick 1 - 3 mm thlck 11/16" - 118") 13/64" - 114") 13/64" - 118") ti 4 - 60 mm thick 15/32" - 2 318") 4 - 60 mm thick 15/32" - 2 318") - - S 3 - 30 mm thick 1118" - 1~118") 3 - 30 mm thick 1118'& ...
-
Makita 4302C - page 15
Oct 01 '87 EN ELECTRONIC JIG SAW Model 4302C Note The switch. noise suppressor and other part configurations may differ from country to country 15 ...
-
Makita 4302C - page 16
MODEL 4302C ITEM NO NO USED Me 3 4 5 6 7 6 9 10 11 12 13 14 17 1s 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 34 35 36 37 38 39 40 41 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 1 1 1 - DESCRIPTION Oct 06 87 US ,,?&, DESCRIPTION Switch Housing Set IWilh Item 611 P," 5 P," 5 flat Washer 5 Roller Flat Washer ...
Do you have a question concerning Makita 4302C?
Use the form below
If you did not solve your problem by using a manual Makita 4302C, ask a question using the form below. If a user had a similar problem with Makita 4302C it is likely that he will want to share the way to solve it.