English dropdown-ico

Manual Belling BE815

28 pages 0.5 mb
Download

Go to site of 28

Summary
  • Belling BE815 - page 1

    BE815 Combi Fridge Freezer INSTALLATION AND USER INSTRUCTIONS You must read these instructions prior to using the appliance and retain them for future reference. ...

  • Belling BE815 - page 2

    ...

  • Belling BE815 - page 3

    Cor. er.s Introduction & safety warnings .......................................................................... 2 Electrical requirements ..................................................................................... 3 Transportation instructions ................................................................................ 4 Insta ...

  • Belling BE815 - page 4

    Congratulations on your choice of a quality Appliance which has been designed to give you service for many years. WARNING ! IMPORTANT ! DO NOT connect your appliance to the electricity supply until all packing and transit protectors have been removed. • Leave to stand for at least 4 hours before switching on to allow compressor oil to settle if t ...

  • Belling BE815 - page 5

    GREEN & YELLOW OR GREEN N BLUE OR BLACK BROWN OR RED V) t i C O CORD GRIP C D ELECTRICAL REQUIREMENTS Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply. Rating label is on the left hand side of fridge inner liner. We ...

  • Belling BE815 - page 6

    TRANSPORTATION INSTRUCTIONS 1. The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation. 2. If during the course of transport the appliance has to be transported horizontally, it must only be laid on its left hand side when standing in the front of the appliance. After bri ...

  • Belling BE815 - page 7

    This fridge freezer has been designed to operate in ambient temperatures between +5 and +32 degrees C (41 and 90 degrees F) Therefore if the appliance is installed in an unheated/cold room (eg: conservatory/annex/ shed/garage etc) then the appliance will not operate causing the freezer compartment to run warmer and as a result the storage time of f ...

  • Belling BE815 - page 8

    FROZEN FOOD STORAGE DRAWERS DEFROST WATER COLLECTION CHANNEL GETTING TO KNOW YOUR COMBI FRIDGE / FREEZER DAIRY COMPARTMENT EGG TRAY THERMOSTAT KNOB INTERIOR LIGHT ( 1 ,•• ,• WINE RACK CABINET SHELVES, SALAD CRISPER 6 ...

  • Belling BE815 - page 9

    SUGGESTED ARRANGEMENT OF FOOD IN THE FRIDGE/FREEZER Arrangement Examples (See diagram) 1. Baked, chilled cooked food, dairy products, cans. 2. Wine 3. Meat, sausages, cold cuts. 4. Fruit, vegetables, salads. 3 5. Frozen food and freezing of fresh food. 6. Frozen food. 7. Butter, cheese. 5 8. Small bottles, cans, tubes. 9. Eggs. 10. Tall, large bott ...

  • Belling BE815 - page 10

    TEMPERATURE CONTROL AND ADJUSTMENT Operating temperatures are controlled by the thermostat knob (see diagram) located on the ceiling of fridge compartment. Settings may be made from 1 to 5, 5 being the coldest position. When the appliance is switched on for the first time, the thermostat should be adjusted so that after 24 hours, the average fridge ...

  • Belling BE815 - page 11

    STARTING Final Check Before you start using the fridge/freezer check that: 1. The interior is dry and air can circulate freely at the rear of the cabinet. 2. Clean the interior as recommended under "CLEANING AND CARE." 3. Insert the plug into the wall socket and switch on the electricity supply. • When the door is open the fridge interi ...

  • Belling BE815 - page 12

    FREEZING FRESH FOOD Please observe the following instructions to obtain the best results. Do not freeze too large a quantity at any one time. The quality of the food is best preserved when it is frozen right through to the core as quickly as possible. Do not exceed the freezing capacity of your appliance in 24 h which is 4 kg (9 Ib) Placing warm fo ...

  • Belling BE815 - page 13

    DEFROSTING A) FRIDGE COMPARTMENT The fridge compartment defrosts automatically. The defrosting water runs to the drain tube via a collectioncontainer at the back of the appliance (1). (see diagram) During defrosting water droplets may form at the back of the fridge compartment where concealed evaporator is located. Some droplets may remain on the l ...

  • Belling BE815 - page 14

    CLEANING AND CARE " We recommend that you switch off the appliance at the socket outlet and pull out the mains plug before cleaning. ** Never use any sharp abrasive instrument, soap, household cleaner, detergent and wax polish for cleaning. " Use luke warm water to clean the cabinet of the appliance and wipe it dry. ** Use a damp cloth wr ...

  • Belling BE815 - page 15

    REPLACING THE INTERIOR LIGHT BULB (See diagram) Should the light fail to work, proceed as follows. 1. Switch off at the socket outlet and pull out the mains plug. • You may find it useful to remove shelves for easy access. 2. Use a flat tipped screwdriver to remove the light diffuser cover by inserting the blade in each of the two recesses to pri ...

  • Belling BE815 - page 16

    DO'S AND DON'TS Do- Clean and defrost your appliance regularly (See "Defrosting") Do- Keep raw meat and poultry below cooked food and dairy products. Do- Take off any unusable leaves on vegetables and wipe off any soil. Do- Leave lettuce, cabbage, parsley and cauliflower on the stem. Do- Wrap cheese firstly in greaseproof paper ...

  • Belling BE815 - page 17

    ENERGY SAVING TIPS 1- Ensure your appliance is installed in a well ventilated area. If the ambient temperature is low (but in no case lower than 5 degrees C), then the energy saving will be more. In this case, check temperatures of fridge and freezer compartments with an accurate thermometer and lower the thermostat setting (towards 1) if necessary ...

  • Belling BE815 - page 18

    es) cc min. 200 cm 2 1 min. 200 cm 2 INSTALLATION INSTRUCTIONS (All dimensions are in mm) Ventilation CD OD N OD 0 0 16 ...

  • Belling BE815 - page 19

    Ventilation Ventilation 200 cm2 200 cm 2 Ventilation requirement 17 ...

  • Belling BE815 - page 20

    • 4 Parts are supplied in the plastic bag. Fit plastic trims and door furniture brackets supplied with the product. 18 ...

  • Belling BE815 - page 21

    19 ...

  • Belling BE815 - page 22

    2 mri l l * ". t 4* *_, 2 mOss.k Ensure 2 mm gaps are obtained, adjust if necessary. 20 ...

  • Belling BE815 - page 23

    REVERSING THE DOORS Reverse the doors following numbered instructions. ...

  • Belling BE815 - page 24

    GUARANTEE DETAILS Your new Belling product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. W hat is covered? • Repairs necessary as a result of faulty materials, defective components or manufac- turing defect. • The cost of functional replacement parts, but excluding consumable items ...

  • Belling BE815 - page 25

    HOW TO OBTAIN SERVICE Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the product require attention under guarantee. You should also complete the details below; it will help us assist you when requesting service. (The model number is printed on the Instruction Booklet and the serial numb ...

  • Belling BE815 - page 26

    Technical data Performance Energy efficiency class Energy consumption - Kwh / year Net storage - vol fresh food litres (cu. ft) Net storage - vol frozen food Itrs (cu.ft.) Total net vol - litres (cu. ft) Frozen food compartment rating Conservation time from failure Freezing capacity fresh food - Kg / 24hrs Climate class Operating noise level dB(A) ...

  • Belling BE815 - page 27

    WIRING DIAGRAM 25 ...

  • Belling BE815 - page 28

    BELLING CUSTOMER CARE In case of difficulty within the UK, please call Belling Customer Care Centre Helpline on 0871 22 22 503 When you dial this number you will hear a recorded message and be given a number of options. This indicates that your call has been accepted and is being held in a queue. Calls are answered in strict rotation as our Custome ...

Manufacturer Belling Category Refrigerator

Documents that we receive from a manufacturer of a Belling BE815 can be divided into several groups. They are, among others:
- Belling technical drawings
- BE815 manuals
- Belling product data sheets
- information booklets
- or energy labels Belling BE815
All of them are important, but the most important information from the point of view of use of the device are in the user manual Belling BE815.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Belling BE815, service manual, brief instructions and user manuals Belling BE815. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Belling BE815.

Similar manuals

A complete manual for the device Belling BE815, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Belling BE815 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Belling BE815.

A complete Belling manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Belling BE815 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Belling BE815, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Belling BE815, that we can find in the current document
3. Tips how to use the basic functions of the device Belling BE815 - which should help us in our first steps of using Belling BE815
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Belling BE815
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Belling BE815 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Belling BE815?

Use the form below

If you did not solve your problem by using a manual Belling BE815, ask a question using the form below. If a user had a similar problem with Belling BE815 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)