English dropdown-ico

Manual Miller Electric MTL-17

32 pages 1.43 mb
Download

Go to site of 32

Summary
  • Miller Electric MTL-17 - page 1

    Millerfi January 1994 Form: OM-1563B Effective With Style No. KB-8 OWNERS MANUAL MTL-1 7 Torches ~' F'~~ r. Read and follow these instructions and all safety blocks carefully.  Have only trained and qualified persons install, operate, or service this unit.  Give this manual to the operator. ~ .  For help, call your distrib ...

  • Miller Electric MTL-17 - page 2

    MILLERS TRUE BLU ETM LIMITED WARRANTY Effective January 1.1992 (Equipment with a serial number preface of KC or newer) This Limited warranty suoersedes all previous MILLER warranties and is exclusive with ire other gualantees Or warlantres expressed or implied :I~I LIMITED WARRANTY  Sub~ect to the terms and conditions below. MILLER Elec ...

  • Miller Electric MTL-17 - page 3

    SAFETY PRECAUTIONS FOR GTAW TORCHES ELECTRIC SHOCK can kill. 1. Always wear dry insulating gloves. 2. Insulate yourself from work and ground. 3. Do not touch live electrode or electrical parts. 4. Repair or replace worn, damaged, or cracked torch or cable insulation. 5. Turn oft welding power source before changing tungsten electrode or torch parts ...

  • Miller Electric MTL-17 - page 4

    TABLE OF CONTENTS SECTION 1 - SAFETY INFORMATION . 1 SECTION 2- SPECIFICATIONS 2-1. Duty Cycle 2 SECTION 3- INSTALLATION & OPERATION 3-1. Required Torch Parts And Torch Assembly 2 3-2. Adjusting Flex-Lok Head 3 3-3. Connecting Torch 4 SECTION 4- MAINTENANCE & TROUBLESHOOTING 5 SECTION 5 TUNGSTEN ELECTRODE 5-1. Selecting Tungsten Electrod ...

  • Miller Electric MTL-17 - page 5

    SECTION 1 - SAFETY INFORMATION Figure 1-1. Safety Information SECTION 2- SPECIFICATIONS Table 2-1. Welding Torch modl.t 2.93 Specification Description Model Description MT: Miller Torch; L: Flex Lok; 17: 150 Ampere Rating; V: Gas Valve 12:12-1/2 ft(3.8 m) Cable; 25: 25 ft (7.6 m) Cable; 1: One-Piece Cable Example: MTL-17-12  Miller Torch; Flex L ...

  • Miller Electric MTL-17 - page 6

    2-1. Duty Cycle Obtain the following parts (see Section 6): 1 Tungsten Electrode (See Section 5) 2 Cup 3 Collet Body 4 Standard Collet 5 Reverse Collet Reverse collet improves electrical contact of tungsten electrode. 6 Power Cable Adapter Assembling Torch Body 7 Flex-Lok Head 8 Heat Shield 9 Backcap (Short Backcap Shown) 10 0-Ring Installing Tungs ...

  • Miller Electric MTL-17 - page 7

    3-2. Adjusting Flex-Lok Head CAUTION TOOLS can damage torch.  Do not use hand tools to adjust torch flex-bk head. Hold stem and turn head one lull turn. 1 Head Adjusting Stem 2 Head Turn head and stem to desired angle. Figure 3-2. Adjusting Flex-Lok Head ST-~42 083.A ~1~ Hold stem and turn head until tight. OM-1563 Page 3 ...

  • Miller Electric MTL-17 - page 8

    3-3. Connecting Torch ~ ~ ~ READ SAFETY BLOCKS at beginning 4jj~1 ~ of manual before proceeding. BUILDUP OF SHIELDING GAS can harm health or kill. 0 Shut off shielding gas supply when not in use. warnl.1 9/91 Turn Off welding power source, and If applicable. install high-frequency unit, disconnect input power before in stalling torch. Obtain the fo ...

  • Miller Electric MTL-17 - page 9

    SECTION 4 MAINTENANCE & TROUBLESHOOTING 4.. ~. ~ V~ ~ READSAF of manual ETYBLOCKSatbeginning before proceeding. Figure 4-1. Maintenance Schedule Table 4-1. Troubleshooting N OTE 1 Before using troubleshooting table, check selection and preparation of tungsten electrode according to Section 5. Trouble Remedy Lack of high frequency~ difficulty ...

  • Miller Electric MTL-17 - page 10

    SECTION 5- TUNGSTEN ELECTRODE mod2. I 3/93 NOTE ~ Foradditional information, see your distributor fora handbook on the Gas Tungsten I Arc Welding (GTAW) process. Wear clean gloves to prevent contamination of tungsten electrode. 5-1. Selecting Tungsten Electrode Table 5-1. Tungsten Size Electrode Diameter Amperage Range. Gas Type, - Polarity DC  ...

  • Miller Electric MTL-17 - page 11

    5-2. Preparing Tungsten Figure 5-1. Preparing Tungsten For AC Or DC Electrode Positive (DCEP) Welding H 2-1/2 Times Electrode Diameter 1 Tungsten Electrode 2 Tapered End Grind end of tungsten on fine grit, hard abrasive wheel before weld. ing. Do notuse wheel for other jobs or tungsten can become contami nated causing lower weld quaIity~ Ret S01 ...

  • Miller Electric MTL-17 - page 12

    SECTION 6- PARTS LIST Figure 6-1. Complete Torch Assembly Item Stock No. No. Model No. Description Quantity Figure 6-1. Complete Torch Assembly  OPTIONAL BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS. Fig 6-2 4 11 Fig 6-2  Fig 6-22 16 17 18 6 SB120 867 20 1 2 3 4 . 5 118 526 . . . . FL3L . . . . 116256. .. 30 ...

  • Miller Electric MTL-17 - page 13

    d CONSUMABLE PARTS SELECTOR Standard LenyIh Gas Lens 3GL-XXX Use 3GHS Heat SIseki Stock No 119914 Large Diarrieler Gas Lens 3GLL-XXX Use ~ Neat Shield Stock No 119915 SHADED AREAS INDICATE RECOMMENDED USAGE S-0768 (Note: Cottet Body and Gas Cup required to complete torch). Torches with high Rex composite cable also require a power cable adapter. 0 ...

  • Miller Electric MTL-17 - page 14

    Table 6-1. Cross Reference To Competitive Model COMPETITIVE STOCK NO. MODEL NO. NO. STOCK NO. MODEL NO. COMPETITIVE NO. 116367 116368 116369 116 370 116371 116 379 116 380 116381 116382 116383 116 361 116 362 116363 116364 116365 116 347 116 348 116349 116 350 116351 116 352 116353 116354 116343 116344 3020 3C40 . . . 3C116 3C332 3C418 7C20 . 7C40 ...

  • Miller Electric MTL-17 - page 15

    ...

  • Miller Electric MTL-17 - page 16

    OPTIONS AND ACCESSORIES For TOTAL TIG system, select one each of the following items:  Welding power source  TIG torch  TIG kit (see hG kits listed below)  Coolant system (it using water cooled torch)  Remote control Note: The other items necessary to weld are power source primary cable. shielding gas, and filler metal. KIT FOR MT ...

  • Miller Electric MTL-17 - page 17

    Miller. OWNERS MANUAL ~=l~ ''~7 ~1fJ~ ~r' ~ MTL-1 7 Torches ~/J> ~ ~ U ~  ~ Read and follow these instructions and all safety blocks carefully. Have only trained and qualified persons install, operate, or service this unit. Call your thstributor if you do not understand the directions. j- ~ I Give this manual to the opera ...

  • Miller Electric MTL-17 - page 18

    u-f MILLERS TRUE BLUETM LIMITED WARRANTY Effective January 1. 1992 (Equipment with a serial number preface of KC or newer) This umited warranty supersedes alt previous MtLLER warranties and is erctusiue witn to other guarantees or warranties esoressed or implied :1~. .1 LIMITED WARRANTr Subtect to the terms and conditions betow MILLER Elec ...

  • Miller Electric MTL-17 - page 19

    SAFETY PRECAUTIONS FOR GTAW TORCHES ELECTRIC SHOCK can kill. 1. Always wear dry insulating gloves. Insulate yourself from work and ground. Do not touch live electrode or electrical parts. Repair or replace worn, damaged, or cracked torch or cable insulation. Turn off welding power source before changing tungsten electrode or torch parts. Keep all c ...

  • Miller Electric MTL-17 - page 20

    TABLE OF CONTENTS SECTION 1  SAFETY INFORMATION 1 SECTION 2 SPECIFICATIONS 2-1. DutyCycle 2 SECTION 3-INSTALLATION & OPERATION 3-1. Required Torch Parts And Torch Assembly 2 3-2. Adjusting Flex-Lok Head 3 3-3. Connecting Torch 4 SECTION 4- MAINTENANCE & TROUBLESHOOTING 5 SECTION 5 TUNGSTEN ELECTRODE 5-1. Selecting Tungsten Electrod ...

  • Miller Electric MTL-17 - page 21

    SECTION 1 - SAFETY INFORMATION Figure 1-1. Safety Information SECTION 2- SPECIFICATIONS Table 2-1. Welding Torch 12-1/2 ft (3.8 m) Cable 25 ft (7.6 m) Cable 12-1/2 ft (3.8 m) Cable With Gas Valve 25 ft (7.6 m) Cable With Gas Valve Net: 2.5 lb (1.1 kg), Ship: 3 lb (1.4 kg) Net: 4.5 lb (2kg); Ship: 5 lb (2.3 kg) Net: 2.5 lb (1.1 kg); Ship: 3 lb (1.4 ...

  • Miller Electric MTL-17 - page 22

    2-1. Duty Cycle CAUTION ;~ WELDING LONGER THAN RATED DUTY CYCLE can damage torch and void warranty.  Do not weld at rated load longer than shown below. wiwarne.r 8/93 100% Duty Cycle At 150 Amperes Using Argon Gas Definition Duty Cycle is percentageof 10 minutes that torch can weld at rated load without overheating. Continuous Welding sb1 5 8 ...

  • Miller Electric MTL-17 - page 23

    3-2. Adjusting Flex-Lok Head a CAUTION_____ TOOLS can damage torch.  Do not use hand tools to adjust torch flex-bk head. Hold stem and turn head one full turn. I 1 Head Adjusting Stem 2 Head Turn head and stem to desired angle. Figure 3-2. Adjusting Flex-Lok Head ST.142 083A I Hold stem and turn head until tight. OM-1563 Page 3 ...

  • Miller Electric MTL-17 - page 24

    3-3. Connecting Torch l.~ 4//~~~ READ SAFETY BLOCKS at beginning BUILDUP OF SHIELDING GAS can harm health or kill. S Shut off shielding gas supply when not in use. warnll 9/91 1~ If applicable, install high-frequency unit. Turn Off welding power source, and disconnect input power before in stalling torch. Obtain the following hose: Torch With G ...

  • Miller Electric MTL-17 - page 25

    SECTION 4 MAINTENANCE & TROUBLESHOOTING ~.: k~-~ ~ READ SAF of manual ETY BLOCKS at beginning before proceeding. Figure 4-1. Maintenance Schedule Table 4-1. Troubleshooting NOTE Before using troubleshooting fable, check select ion and preparation of tungsten ~_. electrode according to Section 5. Turn Off all power before maintaining. Torch C ...

  • Miller Electric MTL-17 - page 26

    SECTION 5 TUNGSTEN ELECTRODE  Typical argon shielding gas flow rates are 15 to 35 cfh (cubic feet per hour). Not Recommended. The figures listed are intended as a guide and are a composite of recommendations from manufacturers, mod2.1 3/93 NOTE ~ Foradditional in formation, see yourdistributorfora handbook on the Gas Tungsten Arc Welding (GTA ...

  • Miller Electric MTL-17 - page 27

    5-2. Preparing Tungsten a CAUTION FLYING SPARKS AND HOT METAL can cause injury and start fires.  Shape tungsten electrode only on grinder with properguards in a safe location wearing proper face, hand, and body protection.  Keep flammables away. w~rn2.I 9/91 1 Tungsten Electrode 2 2 Tapered End Grind end of tungsten on fine grit, hard abrasiv ...

  • Miller Electric MTL-17 - page 28

    SECTION 6- PARTS LIST Figure 6-1. Complete Torch Assembly Item Stock No. No. Model No. Description Figure 6-1. CompleteTorch Assembly Quantity . OPTIONAL BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS. OM-1563 Page 8 Fig 6-2 4 Fig6-2 3. 16 18 J27 / 6 F-i 20 SB120 B67 1 2 3 4 . 5 . . 118 526 . . . . FL3L . . . . . 11 ...

  • Miller Electric MTL-17 - page 29

    CONSUMABLE PARTS SELECTOR Standard Lerrgrh Gas Lens 3GL-XXX Use 3GHS Heal Shield Stock No 119914 Large Diameter Gas Lens 3GLLXXX Use 3GHSLO Heat Sheld Stock NO 119915 SHADED AREAS INDICATE RECOMMENDED USAGE S-0768 (Note: Coltet Body and Gas Cup required to complete torch). Torches with high Rex composite cable also require a power cable adapter. ...

  • Miller Electric MTL-17 - page 30

    Table 6-1. Cross Reference To Competitive Model COMPETITIVE STOCK NO. MODEL NO. NO. COMPETITIVE STOCK NO. MODEL NO. NO. 116367 116 368 116369 116370 116371 116 379 116380 116381 116 382 116 383 116361 116 362 3020 3C40 3C116 3C332 3C418 7C20 7C40 7C116 70332 7C418 3CB20 3CB40 10N21 10N22 10N23 10N24 10N25 N/A N/A N/A N/A N/A 10N29 1 0N30 119 934 11 ...

  • Miller Electric MTL-17 - page 31

    ...

  • Miller Electric MTL-17 - page 32

    OPTIONS AND ACCESSORIES For TOTAL TlG~ system, select one each of the following items:  Welding power source  TIG torch  TIG kit (see TIC kits listed below)  Coolant system (if using water cooled torch)  Remote control Note: The other items necessary to weld are power source primary cable. shielding gas, and filler metal. KIT FOR ...

Manufacturer Miller Electric Category Welder

Documents that we receive from a manufacturer of a Miller Electric MTL-17 can be divided into several groups. They are, among others:
- Miller Electric technical drawings
- MTL-17 manuals
- Miller Electric product data sheets
- information booklets
- or energy labels Miller Electric MTL-17
All of them are important, but the most important information from the point of view of use of the device are in the user manual Miller Electric MTL-17.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Miller Electric MTL-17, service manual, brief instructions and user manuals Miller Electric MTL-17. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Miller Electric MTL-17.

Similar manuals

A complete manual for the device Miller Electric MTL-17, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Miller Electric MTL-17 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Miller Electric MTL-17.

A complete Miller Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Miller Electric MTL-17 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Miller Electric MTL-17, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Miller Electric MTL-17, that we can find in the current document
3. Tips how to use the basic functions of the device Miller Electric MTL-17 - which should help us in our first steps of using Miller Electric MTL-17
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Miller Electric MTL-17
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Miller Electric MTL-17 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Miller Electric MTL-17?

Use the form below

If you did not solve your problem by using a manual Miller Electric MTL-17, ask a question using the form below. If a user had a similar problem with Miller Electric MTL-17 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)