English dropdown-ico

Manual Patton electronic 1092ARC

20 pages 14.38 mb
Download

Go to site of 20

Summary
  • Patton electronic 1092ARC - page 1

    USE R MANUA L MODEL 1092AR C High Speed, 2-Wire/4-Wire , Synchronous an d Asynchronous Rack Moun t Modem Card SALES OFFIC E (301)975-100 0 TECHNICAL SUPPOR T (301)975-100 7 http://ww w.patton.co m Part# 07M1092ARC- C Doc# 033041U B Revised 03/23/0 0 An ISO-9001 Certifie d Compan y ...

  • Patton electronic 1092ARC - page 2

    1.0 WARRANTY INFORM ATION Patton Electronic s warrants all Model 1092ARC components t o be free from defects, and wil l — at our optio n — repair or replace th e product should it fail within one year from the first date of shipment . This warranty is limited to defects in workmanship or materials, an d does not cover customer damage, abuse or ...

  • Patton electronic 1092ARC - page 3

    2.0 GENERAL INFORM ATIO N Thank you for your purchase of this Patton Electronics product . This product has been thoroughly inspected and tested and i s warranted for One Y ear parts and labor. If any questions arise durin g installation or use of this product, please contact P atton Electronics ’ T echnical Support at: (301) 975-1007 . 2.1 FE AT ...

  • Patton electronic 1092ARC - page 4

    3.0 CONFIGUR ATIO N This section describes the hardware and software configuratio n switches and jumpers, and provides detailed instructions for all possibl e settings. Refer to the Model 1001MC SNMP Management Card Use r Manual for SNMP options . 3.1 Configure the Hardware Switche s The Model 1092ARC Series front card default s to the use o f hard ...

  • Patton electronic 1092ARC - page 5

    3.1.2 Configuration Switch Set “S1 ” The configuration switches on S1 allow you to specify the dat a rate, async/sync data format, transmit clock source and response t o RDL request. Default settings of S1 are shown in the table belo w . Switches S1-1 and S1-2: Data Rat e Use Switches S1-1 and S1-2 with Switch S5- 1 to determine th e operable S ...

  • Patton electronic 1092ARC - page 6

    Switch S1-8: Response to Remote Loo p Reques t Use Switch S1-8 to allow the Model 1092ARC to enter the Remot e Digital Loopback diagnostic test when requested to do so by the far en d modem. For example, when Switch S1-8 is set to “ON”, it will ente r RDL mode (See Section 5.2.2) when requested to do so by the remot e modem . S1- 8 Settin g O n ...

  • Patton electronic 1092ARC - page 7

    Switch S5-2: 2-Wire/4-Wir e Use Switch S5-2 to configure 2-Wire or 4-Wire operation . S5- 2 Settin g Descriptio n Of f 2-Wir e 2-Wire Operatio n O n 4-Wir e 4-Wire Operatio n Switch S5-3: Enable LAL and RDL from DT E Use Switch S5-3 to enable or disable the Local Analog Loopbac k and Remote Digital Loopback control from the DTE . S5- 3 Settin g Des ...

  • Patton electronic 1092ARC - page 8

    MAIN MENU Option 1: Display Active Configuratio n Select Option 1 to display the most recent configuration of the loca l Model 1092ARC (See below). The Model 1092ARC uses the activ e configuration for its operation. If you make changes to th e configuration, you must select MAIN MENU Option 8. This will updat e the unit to the new active configurat ...

  • Patton electronic 1092ARC - page 9

    2. Data Forma t Select Option 2 in the SOFTWARE CONFIGUR A TIO N Menu t o select the sync data format (See below). 3. Clock Mod e Select Option 3 in the SOFTWARE CONFIGUR A TION Menu t o select the sync clock mode (See below) . Set this option as follows : Master Clock - Interna l : Select Item 1 to use the Model 1092ARC internal reference clock as ...

  • Patton electronic 1092ARC - page 10

    7. DTE Controlled Remote Digital Loo p Select Option 7 in the SOFTWARE CONFIGUR A TIO N Menu t o enable DTE control of the Remote Digital Loop Menu (See below). Th e Remote Digital Loop on the 1092ARC can be controlled from the DT E interface by selecting Enable (Option 1). T o instruct the 1092ARC t o ignore this request from the DTE interface, se ...

  • Patton electronic 1092ARC - page 11

    To run or terminate a particular test, key in the option to get to tha t screen menu. T est Mode options 2,3,7,8 and 9 require the 1092ARC to be in Dat a Mode with the remote 1092ARC. The Model 1092ARC Test Mode s are described below: OF F Terminates all test s 51 1 Initiates the built-in test pattern generator and detector . 511 with Error s Initi ...

  • Patton electronic 1092ARC - page 12

    3.3.1 Mode l 1001RCM12545 Rear Card Strap Setting s Figure 6 shows strap locations for the Model 1001RCM1254 5 (DB-25/RJ-45S) rear cards. These straps determine various groundin g characteristics for the terminal interface and twisted pair lines. JB3 an d JB4 are user configurable. JB2 mus t be set on pegs 1 and 2 . The table below provides an over ...

  • Patton electronic 1092ARC - page 13

    The table below provides an overview of interface strap function s for the rear interface cards. Following the table overview are detaile d descriptions of each strap’s function . DTE Shield (DB-15 Pin 1) & FRGND (JB3 ) In the connected position, this strap links DB-15 pin 1 & fram e ground. In the open position, pin 1 is disconnected fro ...

  • Patton electronic 1092ARC - page 14

    4.0 INS TALLATIO N This section describes the functions of the Model 1001R14 rac k chassis, tells how to install front and rear Model 1092ARC Series card s into the chassis, and how to connect to the twisted pair interface an d the serial interface . 4.1 THE MODEL 1001R14 RACK CHASSI S The Model 1001R14 Rack Chassis (Figure 9, below) has 16 car d s ...

  • Patton electronic 1092ARC - page 15

    4.3.2 Connect to a “DCE” Devic e Since the Model 1092ARC’s serial port is always wired as a DCE , you must use a null mode m cable when connecting to another DC E device such as a CSU/DSU, modem or multiplexer. This cable shoul d be of the shortest possible length that is appropriate to the interface yo u are using. When purchasing or constru ...

  • Patton electronic 1092ARC - page 16

    5.0 OPER ATIO N Once the Model 1092ARC is properly configured and installed, i t should operate transparentl y . This sections describes functions of th e LED status indicators, and the use of the built-in loopback test modes. 5.1 LED S TA TUS INDIC AT OR S The Model 1092ARC features twelve front panel LEDs that monito r power, the DTE signals, net ...

  • Patton electronic 1092ARC - page 17

    To perform an LLB test, follow these steps : 1 . Activate LLB. This may be done in one of three ways: - Move the front panel toggle switch to the right to “Local”. - Raise the LLB signal on the interface (see Appendix B). - Set Local Loop from the VT100 screen . Once LLB is activated, the Model 1092ARC transmitter output i s connected to its ow ...

  • Patton electronic 1092ARC - page 18

    APPENDIX A PA TTON ELECTRONICS MODEL 1095R C FACTORY REPLACEMENT PART S AND ACCESSORIE S Patton Model # Descriptio n 1001RPEM-RA C ................ . 120/240V Rear Power Entry Modul e 1001RPSM-RU I .................. . 120/240V Front Power Supply Modul e 1001RPEM-RD C ................ . DC Rear Power Entry Modul e 1001RPSM-R48 A ............... . 4 ...

  • Patton electronic 1092ARC - page 19

    APPENDIX B (Continued ) PA TTON MODEL 1092ARC TERMINAL INTER FA CE PIN ASSIGNMEN T DB-25F Connector-DC E (RS-232 Interface ) Pin # Signa l 1...........................FG (Frame Ground ) 2.......................... TD ( T ransmit Data ) 3...........................RD (Receive Data ) 4...........................RTS (Request to Send ) 5............... ...

  • Patton electronic 1092ARC - page 20

    3 8 APPENDIX D LINE INTER FA CE PIN ASSIGNMEN T (RJ45 Connector ) Pin Numbe r Signa l 1...................................................N/C (No Connection ) 2...................................................N/C (No Connection ) 3...................................................4 Wire Ti p 4...................................................Ti ...

Manufacturer Patton electronic Category Network Card

Documents that we receive from a manufacturer of a Patton electronic 1092ARC can be divided into several groups. They are, among others:
- Patton electronic technical drawings
- 1092ARC manuals
- Patton electronic product data sheets
- information booklets
- or energy labels Patton electronic 1092ARC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Patton electronic 1092ARC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Patton electronic 1092ARC, service manual, brief instructions and user manuals Patton electronic 1092ARC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Patton electronic 1092ARC.

Similar manuals

A complete manual for the device Patton electronic 1092ARC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Patton electronic 1092ARC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Patton electronic 1092ARC.

A complete Patton electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Patton electronic 1092ARC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Patton electronic 1092ARC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Patton electronic 1092ARC, that we can find in the current document
3. Tips how to use the basic functions of the device Patton electronic 1092ARC - which should help us in our first steps of using Patton electronic 1092ARC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Patton electronic 1092ARC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Patton electronic 1092ARC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Patton electronic 1092ARC?

Use the form below

If you did not solve your problem by using a manual Patton electronic 1092ARC, ask a question using the form below. If a user had a similar problem with Patton electronic 1092ARC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)