English dropdown-ico

Manual Wyse R Class Conversion to WES7

18 pages Not applicable
Download

Go to site of 18

Summary
  • Wyse R Class Conversion to WES7 - page 1

    Inst allation Guide Wyse ® R Class Conversion to WES7 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-18L Rev . B ...

  • Wyse R Class Conversion to WES7 - page 2

    Copyright Notices © 2010, Wyse T echnology Inc. All right s reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not rep roduce, transmit, transcribe, store in a retrieval system, or translate into any language or compute r language, in any form or by any means, electronic, mechanical, magnet ic, optica l, ...

  • Wyse R Class Conversion to WES7 - page 3

    Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling R90L Thin Client Flash and RAM 3 Requirements 3 Procedures 4 What’s Next 6 3 Inst a lling WES7 Firmw are 7 Requirements 7 Procedures 7 T roubleshootin g 13 USB Keys - T roubleshooting Boot Issu ...

  • Wyse R Class Conversion to WES7 - page 4

    iv Contents This page intentionally blank. ...

  • Wyse R Class Conversion to WES7 - page 5

    1 Introduction This guide provides ste p-by-step in structions to c onvert R90L thin clients from XPe to WES7. Caution WES7 firmware requires R class thin clients to h ave a minimum of 4 GB fla sh and 2 GB RAM. Tip After conv erting your thin clie nts, obtain a ny available firmwar e update a t http://www .wyse.com/serviceands upport/support/downlo ...

  • Wyse R Class Conversion to WES7 - page 6

    2 Chapter 1 The Conversion Sof tware Assembly DVD-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • R Class WES7 Conversion Ima ge folder contain ing the following files: · bios.img · cmos.img · commandsXml.xml · CRC.Txt · initrd.pxe · mbr .img · par 1. im g · vmlinuz Overview T o convert your R c ...

  • Wyse R Class Conversion to WES7 - page 7

    2 Inst alling R90L Thin Client Flash and RAM This chapter cont ains information for users of Wyse R90L thin client s who must install new flash and RAM. If you are inst alling firmware only , you can sk ip this chapte r and proceed to"Installing WES7 Firmware." Requirement s • Small Phillips screwdriver • Needle-nose pliers • (Optio ...

  • Wyse R Class Conversion to WES7 - page 8

    4 Chapter 2 Procedures S tep 1: Remove the R90L Thin Client Left Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client. 1. Perform a proper shut down of the thin cli ent by closing all files and ending your session, and then press the power but ...

  • Wyse R Class Conversion to WES7 - page 9

    Installing R90L Thin Client Flash and RAM 5 S tep 2: Install the R90L Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD). All industry-st andard cautions should be fo llowed to avoid ESD. Before you remove or inst all a module, touch an y metal p art of the chassis and keep that contact with the ...

  • Wyse R Class Conversion to WES7 - page 10

    6 Chapter 2 S tep 3: Install the R90L RAM Module Wa r n i n g RAM modules may be susceptible to damage by Electro-S t atic Discharge (ESD). All industry-st andard cautions should be fo llowed to avoid ESD. Before you remove or inst all a module, touch an y metal p art of the chassis and keep that contact with the chassis during the in stallation pr ...

  • Wyse R Class Conversion to WES7 - page 11

    3 Inst alling WES7 Firmware This chapter include s the requirement s and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your thin c lient to WE S7 firmware. Requirement s • Windows XP Professional SP3 or Windows 2003 Server • USB key size should b e 4 GB or la rger (up to 16 GB tested—see "USB Keys - T ro ...

  • Wyse R Class Conversion to WES7 - page 12

    8 Chapter 3 S tep 3: Use Wyse USB Firmware T ool to Config ure a Single USB Key to Inst all Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T o ol wizard (the welcome p age provides the p roduct version and descriptio n, and a link to view the Wyse end user license agreemen t). Figure 7 Wyse USB Firmware T ool ...

  • Wyse R Class Conversion to WES7 - page 13

    Installing WES7 Firmware 9 4. Select the Windows Embedded S t andard 7 OS type o ption. 5. Select the Up date Firmware operation to perform optio n. Tip Although the Preserve dat a p artition check box is automatica lly selected to preserve any existing dat a p artition, y ou can clear the check box if you want to remove the existing da ta in the d ...

  • Wyse R Class Conversion to WES7 - page 14

    10 Chapter 3 Figure 12 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the ov erall prog ress and task pr ogress. 12. After configuration , click Finish to close the wizard and then remove the configure ...

  • Wyse R Class Conversion to WES7 - page 15

    Installing WES7 Firmware 11 S tep 5: V erifying Thin Client Operation After the thin client reboo ts, you can ver ify the Ve r s i o n and that your general client information is cor rect. Figure 13 Client Info rmation (blank exa mple) 1. On the General t ab of the Client Information window ( Star t > All Programs > Wyse Client Information ), ...

  • Wyse R Class Conversion to WES7 - page 16

    12 Chapter 3 S tep 6: Attach a Wyse Conversion Label and Microso ft License Label on Each Converted Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be atta ched to each thin client as shown in Figure 14. Be sure you have purchased the amount of labels you need. Caution Failure to inst ...

  • Wyse R Class Conversion to WES7 - page 17

    Installing WES7 Firmware 13 T roubleshooting This section contains ge neral troubleshooting information . USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing proce sses on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool. If you experience proble ms booting from a configured ...

  • Wyse R Class Conversion to WES7 - page 18

    Inst allation Guide Wys e ® R Class Conversion to WES7 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ® ...

Manufacturer Wyse Category Software Licenses & extens

Documents that we receive from a manufacturer of a Wyse R Class Conversion to WES7 can be divided into several groups. They are, among others:
- Wyse technical drawings
- R Class Conversion to WES7 manuals
- Wyse product data sheets
- information booklets
- or energy labels Wyse R Class Conversion to WES7
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wyse R Class Conversion to WES7.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wyse R Class Conversion to WES7, service manual, brief instructions and user manuals Wyse R Class Conversion to WES7. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wyse R Class Conversion to WES7.

Similar manuals

A complete manual for the device Wyse R Class Conversion to WES7, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wyse R Class Conversion to WES7 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wyse R Class Conversion to WES7.

A complete Wyse manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wyse R Class Conversion to WES7 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wyse R Class Conversion to WES7, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wyse R Class Conversion to WES7, that we can find in the current document
3. Tips how to use the basic functions of the device Wyse R Class Conversion to WES7 - which should help us in our first steps of using Wyse R Class Conversion to WES7
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wyse R Class Conversion to WES7
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wyse R Class Conversion to WES7 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wyse R Class Conversion to WES7?

Use the form below

If you did not solve your problem by using a manual Wyse R Class Conversion to WES7, ask a question using the form below. If a user had a similar problem with Wyse R Class Conversion to WES7 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)