-
Napco Security Technologies GEM-P400 - page 1
Usin g Y our GEM-P400 Security Sy stem ARMED STATUS GEMINI 1 2 3 4 Oi230a page 1 Tuesday, September 16, 1997 08:26 ...
-
Napco Security Technologies GEM-P400 - page 2
Oi230a page 2 Tuesday, September 16, 1997 08:26 ...
-
Napco Security Technologies GEM-P400 - page 3
Congratulations on y our purc hase of an advanc ed GEMINI-P400 Secur ity System. Meticulously developed by a leading manuf actur er of s tate-of- the-art sec urity products, this system will provide you w ith unprecedented peace- of-m ind & inc orpo- rates som e of the m ost sophis ticated f eatures available today. Above all, it has been desig ...
-
Napco Security Technologies GEM-P400 - page 4
Introduction System Information Central Station Phone Num ber: ____________________ Central Station Account Num ber : ____________________ For Service Call: ____________________ Entry Delay : ____________________ Exit Delay: ____________________ Alarm Tim e-out: ____________________ Table of Contents Key pad Controls and Indicator s ............... ...
-
Napco Security Technologies GEM-P400 - page 5
ARMED STAT US GEMINI 1 2 3 4 Key pad Controls and Indi cator s Trouble Light will light and the Keypad sounder will pulse to indicate that a system tr ou- ble is present. (See System troubles, Page 11) Status Light will light when all zones are secure and system is ready to be Armed. Armed Light will light when sy stem is Arm ed, and will flash ...
-
Napco Security Technologies GEM-P400 - page 6
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g Zone num ber will be lit. Secure these zones bef ore proceedin g . If any zones cannot be secured, s ee Bypassin g zones below. 2 ...
-
Napco Security Technologies GEM-P400 - page 7
Protecting Yourself While at Home 1 Before arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g zone number will be lit. Secure thos e zones before proc eedin g . 2 Enter y our User Code and pres s . The g reen Statu s li ...
-
Napco Security Technologies GEM-P400 - page 8
Emergency Buttons The three s ets of em er gency buttons, if progr am m ed, are always active whether the system is ar m ed or disarm ed. Discus s these Buttons with y our installer. The em ergency signal will only be activated when the two respective buttons are pres sed at the sam e tim e. A uxiliary A larm: Simu ltan ...
-
Napco Security Technologies GEM-P400 - page 9
Disarming Your Sy stem when Returning 1 Enter your premises throu g h the Entry/Exit door. The k eypad w ill sound a steady tone to remind you to disarm the system before your Entry Delay tim e ex pires. 2 Enter your User Code and press . The red Ar m e d li g ht will g o out, indicatin g that the system has been dis arm ed. Note: If you mak e ...
-
Napco Security Technologies GEM-P400 - page 10
Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy A rm (when system is dis arm ed) The Easy Arm feature allows the s y stem to be arm ed by pressing f ollowed by . T his will allow the easy arm ing of the sy stem by someone who is not a regula ...
-
Napco Security Technologies GEM-P400 - page 11
The G EM-P400 is constantly monitor ing its own com ponents, as well as all critical servic es, such as AC power and the telephone line, to insure that it is always ready to provide the protection for which it was des igned. W hen a system trouble does occur , it will caution you by lighting the TROUBLE light and beeping the keypad buzz er. If you ...
-
Napco Security Technologies GEM-P400 - page 12
Sy stem Troubles Keypad Beeps or Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 3 W ireless Receiver Trouble A problem has been detected w ith the wireless receiv er. Call installing company for serv ice. 2 Beeps 4 W ireless Receiver Jam A problem has been detected with a w ireless receiver. Call installing company for serv ...
-
Napco Security Technologies GEM-P400 - page 13
Your Installer has assigned a User 1 Code which can be used to not only Arm and Dis arm the system, but also to enter the User Program Mode, where y ou can program other user c odes. The following explains how you will use this code to progr am or erase additional user codes . Entering the User Program Mode Press followed by and enter the Us er 1 c ...
-
Napco Security Technologies GEM-P400 - page 14
A mbush Code - In the event that y ou are forc ed by an intruder to disarm your system, this special code c an be used to disarm the system , and simultaneously send a silent alarm to Central Station. If y our s ystem has the Am bu sh f eatu re enabled, the code assigned as the User 4 code will function as y o ur Ambush Code. A rming / Disarming - ...
-
Napco Security Technologies GEM-P400 - page 15
Notes 15 Oi230a page 15 Tuesday, September 16, 1997 08:26 ...
-
Napco Security Technologies GEM-P400 - page 16
NA PCO LIM I TED WA RRA NTY THE FOLL OW ING STATEM ENT IS REQUI RED BY THE F C C . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to ...
Do you have a question concerning Napco Security Technologies GEM-P400?
Use the form below
If you did not solve your problem by using a manual Napco Security Technologies GEM-P400, ask a question using the form below. If a user had a similar problem with Napco Security Technologies GEM-P400 it is likely that he will want to share the way to solve it.