English dropdown-ico

Manual Hoshizaki L1F015102

22 pages 0.47 mb
Download

Go to site of 22

Summary
  • Hoshizaki L1F015102 - page 1

    SELF-CONT AINED CRESCENT CUBER INSTRUCTION MANUAL KM-201BAH KM-260BAH KM-201BWH KM-260BWH L1F015102 (100109) ...

  • Hoshizaki L1F015102 - page 2

    IMPORT ANT Only qualified service technicians should install, service and maintain the product. No installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/manager should not proceed to operate the product until the installer has instructed them on its proper ope ...

  • Hoshizaki L1F015102 - page 3

    IMPORT ANT 1. This booklet is an integral and essential part of the product and should be handed over to the user . Read the warnings contained in this booklet carefully as they give important indications regarding the safety of the installation, use and maintenance. Please preserve this booklet for any further consultation that may be necessary . ...

  • Hoshizaki L1F015102 - page 4

    1 I. Specifications A. Nameplate Rating Model Amperes Refrigerant Energy Star KM-201BAH 6.1 AMPS R404A 12.0 oz. Applicable KM-260BAH 7.6 AMPS R404A 12.7 oz. Applicable KM-201BWH 5.4 AMPS R404A 10.9 oz. Not applicable KM-260BWH 7.1 AMPS R404A 13.8 oz. Not applicable See the Nameplate for electrical and refrigeration specifications. This Nameplate i ...

  • Hoshizaki L1F015102 - page 5

    2 B. Dimensions/Connections 1. KM-201BAH Unit: mm [inches] ...

  • Hoshizaki L1F015102 - page 6

    3 2. KM-260BAH Unit: mm [inches] ...

  • Hoshizaki L1F015102 - page 7

    4 3. KM-201BWH Unit: mm [inches] ...

  • Hoshizaki L1F015102 - page 8

    5 4. KM-260BWH Unit: mm [inches] ...

  • Hoshizaki L1F015102 - page 9

    6 II. Installation and Operating Instructions A. Checks Before Installation * V isually inspect the exterior of the shipping container , and any severe damage noted should be reported to the carrier . IMPORT ANT 1. Remove shipping carton, tape(s) and packing. If packing material is left in the icemaker , it will not work properly . 2. Ensure all co ...

  • Hoshizaki L1F015102 - page 10

    7 C. Location W ARNING This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Normal operating water temperature should be within +45°F to +90°F (+7°C to +32° C). Operation of the icemaker , for extended periods, outside of these normal temperature ranges may aff ...

  • Hoshizaki L1F015102 - page 11

    8 D. Electrical Connection W ARNING THIS APPLIANCE MUST BE GROUNDED. This icemaker requires a ground that meets the national and local electrical code requirements. T o prevent possible severe electrical shock injury to individuals or extensive damage to equipment , install a proper ground wire to this icemaker . Remove the plug from the electrical ...

  • Hoshizaki L1F015102 - page 12

    9 Fig. 2 Fig. 3 T apped Hole (Leg Mounting) Base from 6” (15.2 cm) to 7” (17.8 cm). Screw the legs tightly into the tapped holes in the base (see Fig. 3). Handle the icemaker carefully not to damage the exterior . F . W ater Supply and Drain Connections - See Figs. 4 and 5 CAUTION T o prevent damage to equipment, do not operate this icemaker wh ...

  • Hoshizaki L1F015102 - page 13

    10 * Drain lines should not be piped directly to the sewer system. An air gap of a minimum of 2 vertical inches (5 cm) should be between the end of the drain pipes from the icemaker and the floor drain. * This icemaker should be installed in accordance with applicable national, state and local regulations. * A plumbing permit and services of a lic ...

  • Hoshizaki L1F015102 - page 14

    11 W ater Supply Inlet 1/2” FPT Drain Outlet 3/4” FPT Fig. 5 KM-201BWH KM-260BWH Condenser W ater Outlet 1/2” FPT Condenser W ater Inlet 1/2” FPT Shut-off V alve Drain V alve Shut-off V alve T o approved floor drain T wo-inch (5 cm) air gap Drain Floor Separate piping to approved drain. Leave a two-inch (5 cm) vertical air gap between the ...

  • Hoshizaki L1F015102 - page 15

    12 G. Final Checklist 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7° C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +32°C) all year around? 3) Is there at least 2” (5 cm) clearance at the right side for proper air circulation and at least 0.6” (15 ...

  • Hoshizaki L1F015102 - page 16

    13 H. Startup CAUTION 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned of f, wait for at least 3 minutes before restarting the icemaker to prevent damage to the Compressor . 3. T o prevent damage to the Water Pump, do not leave the Control Switch in the “SERVICE” position for extended perio ...

  • Hoshizaki L1F015102 - page 17

    14 III. Cleaning and Maintenance Instructions IMPORT ANT Ensure all components, fasteners and screws are securely in place after any maintenance or cleaning is done to the equipment . A. Cleaning W ARNING 1 . Hoshizaki recommends cleaning this unit at least once a year . More frequent cleaning, however , may be required in some existing water condi ...

  • Hoshizaki L1F015102 - page 18

    15 7) After 30 minutes, move the Control Switch to the “OFF” position. 8) Same as step 4. 9) Move the Control Switch to the “ICE” position to fill the W ater T ank with water . 10) After 3 minutes, move the Control Switch to the “SERVICE” position and the Service Switch to the “W ASH” position. 1 1) After 5 minutes, move the Contro ...

  • Hoshizaki L1F015102 - page 19

    16 17) Wash the Bin Control Switch, W ater T ank, Float Switch, Cube Guide and Overflow Pipe by using a nylon scouring pad, brushes and the cleaning solution. In addition to the removed parts, also wash the bin liner and Bracket (L) (R) with the solution. 18) Discard the cleaning solution and rinse the parts thoroughly with water . 2. Sanitizing P ...

  • Hoshizaki L1F015102 - page 20

    17 2 ) Soak the removed parts from step 17 above in a clean container containing the sanitizing solution. After allowing the parts to soak for 10 minutes, wash them with the solution. Also wash the bin liner , Bracket (L) (R) with the solution. 3) Discard the sanitizing solution and rinse the parts thoroughly with water . 4) Replace the removed par ...

  • Hoshizaki L1F015102 - page 21

    18 * The Storage Bin is for ice use only . Do not store anything else in the bin. * Keep the scoop clean. Clean it by using a neutral cleaner and rinse thoroughly . * Clean the bin liner by using a neutral cleaner . Rinse thoroughly after cleaning. 3. Air Filter The plastic mesh Air Filter removes dirt or dust from the air , and keeps the Condenser ...

  • Hoshizaki L1F015102 - page 22

    19 5) Allow the line to drain by gravity . 6) Attach compressed air or carbon dioxide supply to the potable water supply line Drain V alve. 7) Move the Control Switch to the “ICE” position. 8) Quickly blow the potable water supply line out using compressed air or carbon dioxide. 2. Drain the potable W ater T ank: 1) Move the Control Switch to t ...

Manufacturer Hoshizaki Category Ice Maker

Documents that we receive from a manufacturer of a Hoshizaki L1F015102 can be divided into several groups. They are, among others:
- Hoshizaki technical drawings
- L1F015102 manuals
- Hoshizaki product data sheets
- information booklets
- or energy labels Hoshizaki L1F015102
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hoshizaki L1F015102.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hoshizaki L1F015102, service manual, brief instructions and user manuals Hoshizaki L1F015102. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hoshizaki L1F015102.

Similar manuals

A complete manual for the device Hoshizaki L1F015102, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hoshizaki L1F015102 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hoshizaki L1F015102.

A complete Hoshizaki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hoshizaki L1F015102 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hoshizaki L1F015102, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hoshizaki L1F015102, that we can find in the current document
3. Tips how to use the basic functions of the device Hoshizaki L1F015102 - which should help us in our first steps of using Hoshizaki L1F015102
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hoshizaki L1F015102
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hoshizaki L1F015102 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hoshizaki L1F015102?

Use the form below

If you did not solve your problem by using a manual Hoshizaki L1F015102, ask a question using the form below. If a user had a similar problem with Hoshizaki L1F015102 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)