English dropdown-ico

Manual Diamond D1000.1

16 pages 2.44 mb
Download

Go to site of 16

Summary
  • Diamond D1000.1 - page 1

    D400.1 | D600.1 | D1000.1 AMPLIFIER INST ALL A TION MANUAL D300.2 | D300.4 | D600.4 ...

  • Diamond D1000.1 - page 2

    2 Congratulations! Thank you for choosing a new Diamond Audio amplier . Diamond Audio ampliers are engineered and produced with the highest quality materi- als and incorporate the latest technology . We think you will nd your new Diamond Audio amplier meets or exceeds your expectations and provides excellent value. Properly installed, y ...

  • Diamond D1000.1 - page 3

    3 Fr equency Response: 20Hz to 20KHz +/-1 dB Signal to Noise Ratio: > 90dBA (20 to 20kHz) Channel Separation 60dB THD+N(T otal Harmonic Distortion + Noise) < 0.02%(Output-1W 4 Ohms) RCA Input Sensitivity: 150mV to 5V Min to Max V oltage requir ements 9V to 15.5V DC High/Low Pass Cr ossover: 12dB/Oct Variabl e Fr om 50-250Hz Cros sover Cong ...

  • Diamond D1000.1 - page 4

    4 Connections and Contr ols This section describes all of the terminals and adjustments. 4 gauge power and ground wir e is recommended for all models. 2 and 4 Channel Models ...

  • Diamond D1000.1 - page 5

    5 4 gauge power and ground wir e is recommended for all models. Connections and Contr ols This section describes all of the terminals and adjustments. Mono Models ...

  • Diamond D1000.1 - page 6

    6 RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type audio cables, keeping them away from power wiring wher ever possible. On the 4 channel amplifiers “Fr ont” and “Rear” input jacks are present. The“Pass-Thru” output allows the signa ...

  • Diamond D1000.1 - page 7

    7 Strapping Amplifiers (D600.1, D1000.1) MASTER SLA VE Wiring 1) Select one amplier t o be the mas ter amplier and one amplier to be the slave amplier . (All EQ and gain contr ols on the slave amp ar e disabled) 2) Set the phase adjustmen t switch on the Master amplier to 0° and the phase adjustment switch on the Slave amplier t ...

  • Diamond D1000.1 - page 8

    8 ...

  • Diamond D1000.1 - page 9

    9 Installation Guidelines T ools and Supplies Listed bel ow ar e the tools and supplies needed to compl ete this installation: • V olt/Ohm Meter • Wir e strippers and wir e cutters • #2 Phillips scr ewdriver • Battery post wr ench • Hand held drill w/assorted bits • High quality electric al tape or heatshrink tubing • Soldering ir on ...

  • Diamond D1000.1 - page 10

    10 Mounting Locations Engine Compartment Never mount this unit in the engine c ompartment. Mounting the unit in the engine compartment will void your warranty . T runk Mounting Mounting the amplier v ertically will pr ovide adequate cooling of the amplier . If you will be mounting it t o an existing panel, be sur e it’ s not prone to e xces ...

  • Diamond D1000.1 - page 11

    11 3) T rim the power cable within 18 inches (45.7mm) of the positiv e battery pos t and splice in a in-line fuse holder . DO NOT inst all the fuse at this time. 4) Strip 1/2 inch (12.7mm) from the battery end of the power cabl e and crimp a lar ge ring terminal t o the cabl e. Connect the ring terminal to the positive (+) battery pos t. 5) Pr epar ...

  • Diamond D1000.1 - page 12

    12 8) Connect from sour ce signal by connecting the RCA audio cabl es to the input jacks at the ampli- er . 9) Connect the car speak ers. Speakers should be 4 Ohms. If connecting one speaker per channel as shown in the diagrams (except where noted on D400.1, D600.1, D1000.1). Strip the speak er wir es 1/2” (12.7mm) and insert int o the speaker ...

  • Diamond D1000.1 - page 13

    13 +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX2 FL FR RL RR +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX2 FL FR RL RR +12V GND REM 2 MIN POWER PROTECT SPEAKER FUSE 20 AX 2 FL FR RL RR D300.4, D600.4 4-Channel Amplifier 4 Channel Mode, 1 speaker per channel 3 Channel Mode, 1 pair stereo plus one bridged channel 2 Channel Mode, both p ...

  • Diamond D1000.1 - page 14

    14 Installing the Remote Le vel Controll er The D400.1, D600.1, & D1000.1 come packaged with a remote le vel contr ol. This allows you to contr ol the level by attenuating the amplitude or increasing (up to the maximum set-point) of the amplier’ s input gain c ontrol. This contr ol does not add additional gain, it simpl y allo ws you to c ...

  • Diamond D1000.1 - page 15

    15 Adjustment of Built-In Crosso ver (All Models) Placing the switch in the FULL position sets the amplier to F ull Range . This setting all ows ALL frequencies to pass to the speaker s. (Not availabl e on D600.1, & D1000.1). Placing the switch in the HP or LP position activates the cr ossover . Placing the switch in the HP position sets the ...

  • Diamond D1000.1 - page 16

    041807 Diamond W arranty Diamond Audio warrants this product to be fr ee fr om def ects in material and w orkmanship for a period of one (1) year fr om the original date of pur chase pr ovided it was purchased from an authorized DA T r etailer within the United States. However, if this pr oduct is installed by an authorized DA T retail er, the warr ...

Manufacturer Diamond Category Stereo Amplifier

Documents that we receive from a manufacturer of a Diamond D1000.1 can be divided into several groups. They are, among others:
- Diamond technical drawings
- D1000.1 manuals
- Diamond product data sheets
- information booklets
- or energy labels Diamond D1000.1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Diamond D1000.1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Diamond D1000.1, service manual, brief instructions and user manuals Diamond D1000.1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Diamond D1000.1.

Similar manuals

A complete manual for the device Diamond D1000.1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Diamond D1000.1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Diamond D1000.1.

A complete Diamond manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Diamond D1000.1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Diamond D1000.1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Diamond D1000.1, that we can find in the current document
3. Tips how to use the basic functions of the device Diamond D1000.1 - which should help us in our first steps of using Diamond D1000.1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Diamond D1000.1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Diamond D1000.1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Diamond D1000.1?

Use the form below

If you did not solve your problem by using a manual Diamond D1000.1, ask a question using the form below. If a user had a similar problem with Diamond D1000.1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)