English dropdown-ico

Manual Hatco FR2 Series

16 pages 0.64 mb
Download

Go to site of 16

Summary
  • Hatco FR2 Series - page 1

    HYDRO-HEA TER Food Rethermalizers/Hot Food T able Heater FR2 Series Inst allation & Operating Manual I&W #07.05.143.00 This manual contains import ant safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury . If you are unable ...

  • Hatco FR2 Series - page 2

    i INTRODUCTION Hatco FR2 Hydro-Heater Food Rethermalizers/Hot Food T able Heaters are designed to supply temperature-controlled water to a holding vessel (sink or tank) located above the heater . W ater flows by natural convection from the holding vessel directly into a tubular water chamber with heating elements uniquely wrapped on the out side of ...

  • Hatco FR2 Series - page 3

    CAUTIONS W ater in the unit and holding vessel is very hot. Wear protective gloves and proper attire when operating to avoid injury . Do not use extension pipes on the inlet and outlet connections on heater unit s. Poor performance or unsafe conditions may occur . CAUTIONS Do not overtighten unions or nut s. Overtightening may cause leaks. Do not t ...

  • Hatco FR2 Series - page 4

    MODEL DESCRIPTIONS 2 ALL MODELS The Hydro-Heater mounts easily to the underside of a holding vessel, leaving the entire vessel area free. Units are shipped ready to inst all with all gaskets and fittings. Hydro-Heaters include a stainless steel front, powder coated body , a low- water cut-off system and a convenient drain outlet. FR2 MODELS The Hat ...

  • Hatco FR2 Series - page 5

    SPECIFICA TIONS 3 Form No. FR2M-0604 Kilowatt s Wire Sizing Fuse or Model V olt age (kW) Phase Amp s A WG* † Circuit Breaker* Shipping Weight FR2-3 208 3 1 14.5 12 20 24 lbs. (1 1 kg) FR2-4 208 4 1 19.2 12 30 24 lbs. (1 1 kg) FR2-6 208 6 1 28.8 10 40 27 lbs. (12 kg) FR2-3 240 3 1 12.5 12 20 24 lbs. (1 1 kg) FR2-4 240 4 1 16.7 12 30 24 lbs. (1 1 k ...

  • Hatco FR2 Series - page 6

    SPECIFICA TIONS 4 Form No. FR2M-0604 DIMENSIONS A C B ELECTRICAL Install a fused disconnect switch or circuit breaker sized according to the applicable Electrical Rating Chart . The wiring from the switch or circuit breaker to the Hatco unit must be in accordance with local electrical requirements and codes. W ARNING For proper electrical inst alla ...

  • Hatco FR2 Series - page 7

    INST ALLA TION 5 Form No. FR2M-0604 PLUMBING An adhesive backed paper template is shipped with the unit and is used to locate the sink strainer holes. Use the following procedure to install the heater unit to the holding vessel. NOTE: The FR2 heater should be positioned with no more than 3' (914 mm) on either side when mounted under holding ve ...

  • Hatco FR2 Series - page 8

    INST ALLA TION 6 Form No. FR2M-0604 CAUTION W ater Quality Requirement s - Incoming water in excess of 3.0 grains of hardness per gallon (GPG) (.75 grains of hardness per liter) must be treated or sof tened before being supplied to a Hydro-Heater . W ater cont aining over 3.0 GPG(.75 GPL) will decrease the efficiency and reduce the operating life o ...

  • Hatco FR2 Series - page 9

    OPERA TION 7 W ARNINGS Hatco FR2 series unit s are designed for commercial use only by properly trained personnel! W ARNINGS Unit s are designed to heat water up to 190ºF (88ºC). T o avoid any injury or damage DO NOT set temperature controls to a setting higher than 190ºF (88ºC). CAUTION W ater in the unit and holding vessel is very hot. Wear p ...

  • Hatco FR2 Series - page 10

    OPERA TION 8 Form No. FR2M-0604 W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: MINUTES TO HEA T T ABLE 9" (23 cm) DEEP W A TER - 750 W A TTS PER SQUARE FOOT OF VESSEL TOP 70 80 90 100 1 10 120 130 140 150 160 170 180 (21) (27) (32) (38) (43) (49) (54) (60) ...

  • Hatco FR2 Series - page 11

    MAINTENANCE 9 GENERAL W ARNING T o avoid any injury , turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. Recommended Cleaning Schedule Complete draining and cleaning should be done • On a daily basis. • Whene ...

  • Hatco FR2 Series - page 12

    MAINTENANCE 10 Form No. FR2M-0604 WEEKL Y (See Figure 8) 1. T urn power switch to the OFF position. 2. Drain holding vessel to discharge visible water and debris. 3. Wipe visible deposits from the sink or t ank. 4. Remove clean-out caps (2- or 3-element unit s only). 5. Inspect for lime and sediment build-up at the sump drain outlet and heating ele ...

  • Hatco FR2 Series - page 13

    MAINTENANCE 11 Form No. FR2M-0604 6. After cleaning, drain all expended solution from the unit through the sump drain. 7. Thoroughly wash heater tank with fresh water for several minutes until discharge is clear and all deliming solution has been removed and rinsed. 8. Close sump drain by moving handle all of the way forward until it stop s . 9. Fo ...

  • Hatco FR2 Series - page 14

    12 Form No. FR2M-0604 HA TCO LIMITED W ARRANTY 1. PRODUCT W ARRANTY Hatco warrants the product s that it manufactures (the “Products”) to be free from defect s in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’ s written ins ...

  • Hatco FR2 Series - page 15

    13 Form No. FR2M-0604 NOTES ...

  • Hatco FR2 Series - page 16

    HA TCO CORPORA TION P .O. Box 340500, Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www .hatcocorp.com HA TCO AUTHORIZED P ARTS DISTRIBUTORS Printed in U.S.A. June 2004 ALABAMA Jones McLeod Appl. Svc. Birmingham 205-251-0159 ARIZONA Auth. Comm. Food Equip. Phoenix 60 ...

Manufacturer Hatco Category Food Warmer

Documents that we receive from a manufacturer of a Hatco FR2 Series can be divided into several groups. They are, among others:
- Hatco technical drawings
- FR2 Series manuals
- Hatco product data sheets
- information booklets
- or energy labels Hatco FR2 Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hatco FR2 Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hatco FR2 Series, service manual, brief instructions and user manuals Hatco FR2 Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hatco FR2 Series.

Similar manuals

A complete manual for the device Hatco FR2 Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hatco FR2 Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hatco FR2 Series.

A complete Hatco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hatco FR2 Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hatco FR2 Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hatco FR2 Series, that we can find in the current document
3. Tips how to use the basic functions of the device Hatco FR2 Series - which should help us in our first steps of using Hatco FR2 Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hatco FR2 Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hatco FR2 Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hatco FR2 Series?

Use the form below

If you did not solve your problem by using a manual Hatco FR2 Series, ask a question using the form below. If a user had a similar problem with Hatco FR2 Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)