English dropdown-ico

Manual Miele KM 2256 G

60 pages Not applicable
Download

Go to site of 60

Summary
  • Miele KM 2256 G - page 1

    Operating and installation instructions Gas cooktops KM 2256 KM 2257 KM 2257-1 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 012 921 en - AU, NZ ...

  • Miele KM 2256 G - page 2

    WO This appliance can be used in countries other than those specified on the appliance. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For use in other countries, please contact Miele in your country. 2 ...

  • Miele KM 2256 G - page 3

    Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Cooktop ..........................................................5 Burners ..........................................................6 Accessories .......................................................8 Warning and safety instruction ...

  • Miele KM 2256 G - page 4

    Safety instructions for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Safety clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 KM 2256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ...

  • Miele KM 2256 G - page 5

    Cooktop KM 2256 / KM 2257 / KM 2257-1 a Simmer burner b Extra high-speed burner c Dual Wok d High-speed burner e Standard burner f Pan support (in three sections) g Combi insert h Wok ring Controls: i Front left j Back left k Middle l Back right m Front right Guide to the appliance 5 ...

  • Miele KM 2256 G - page 6

    Burners Dual Wok burner o Inner cover to burner p Outer cover to burner q Burner ring r Burner head s Ignition safety device t Ignitor u Burner base Position of the burner components The proper functioning of the burner can only be guaranteed if the burner components are positioned correctly: The lobe a on the burner cap must fit into the recess b ...

  • Miele KM 2256 G - page 7

    Simmer, standard, high-speed and extra high-speed burners n Burner cap r Burner head s Ignition safety device t Ignitor u Burner base Guide to the appliance 7 ...

  • Miele KM 2256 G - page 8

    Accessories Wok ring The wok ring supplied gives additional stability to the wok, especially to those with a rounded base. Combi insert for small and large pans If you are using a pan which is smaller or larger than that recommended in the table under "Pans", then the combi insert supplied must be used. Guide to the appliance 8 ...

  • Miele KM 2256 G - page 9

    This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important notes on installation, safet ...

  • Miele KM 2256 G - page 10

    Safety with children ~ Children should be supervised to ensure that they do not play with the appliance. ~ Older children may use the gas cooktop only when its operation has been clearly explained to them and they are able to use it safely. They must be aware of the potential dangers caused by incorrect operation. ~ The appliance gets hot when in u ...

  • Miele KM 2256 G - page 11

    Technical safety ~ Before installation, check the appliance for visible signs of damage. Do not install and use a damaged appliance. A damaged appliance is dangerous. ~ The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local a ...

  • Miele KM 2256 G - page 12

    ~ The gas cooktop must be disconnected from the gas supply and mains electricity before repairs and maintenance work is carried out. It is only completely isolated from the electricity supply when: – the mains fuse is disconnected, – the screw-out fuse is removed (in countries where this is applicable), – it is switched off at the wall socket ...

  • Miele KM 2256 G - page 13

    Correct use ~ The appliance gets hot when in use and remains hot for quite a while after being switched off. Do not touch it whilst it could still be hot. ~ When using a rangehood over the cooktop, ensure that the burner is always covered with a pan when in use. Otherwise flames could be drawn up by the suction of the rangehood, parts of which coul ...

  • Miele KM 2256 G - page 14

    ~ Pans must be the correct size for the burner they are used on (see "Suitable pans"). A pan which is too small will be unstable on the pan support. If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the cooktop. Miele will not accept l ...

  • Miele KM 2256 G - page 15

    ~ Avoid allowing liquids or foods containing salt to spill onto the cooktop. If salty foods or liquids do get on the cooktop, they should be removed as soon as possible to avoid the risk of corrosion. ~ If the cooktop is built-in behind a furniture door, it must only be operated when the door is open. Close the furniture door only once the applianc ...

  • Miele KM 2256 G - page 16

    Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation. Rather than just thro ...

  • Miele KM 2256 G - page 17

    Please adhere the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet. Cleaning for the first time ^ Remove any protective foil and adhesive labels. ^ Clean all removable parts of the burners with a solution of warm water and a small amount of washi ...

  • Miele KM 2256 G - page 18

    Rapid ignition system The appliance is supplied with a rapid ignition system with the following features: – After the flame is ignited, the cooktop control can be released immediately. – Automatic re-ignition Should the flame be extinguished, e. g. by a gust of air, the burner will re-ignite automatically. If re-ignition is unsuccessful, the ga ...

  • Miele KM 2256 G - page 19

    Switching on , Do not leave the appliance unattended whilst it is being used. ^ The control for the burner required must be pressed in and turned anti-clockwise to the largest flame symbol to switch on. The ignition clicks, and the gas is lit. If the burner does not ignite, turn the control to " ß ". Ensure that the room is well ventilat ...

  • Miele KM 2256 G - page 20

    Regulating the flame Regulate the flame so that it does not spread out beyond the sides of the pan. As the outer part of the flame is much hotter than the centre, the tips of the flames should stay beneath the pan base. Flame tips which extend beyond the sides of the pan merely warm up the air in the room and can also damage pan handles and increas ...

  • Miele KM 2256 G - page 21

    Burner Min. pan base diameter in cm Simmer Standard High-speed Extra high-speed Dual Wok 10 10 12 14 15 Max. diameter at top of pan in cm Without With combi insert Simmer Standard High-speed Extra high-speed Dual Wok 22 22 24 24 24 24 24 26 26 26 – Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diam ...

  • Miele KM 2256 G - page 22

    Wok ring Use the wok ring supplied to give additional stability, especially to woks with a rounded base. Make sure that the wok ring is securely in the correct position. See illustration. Combi insert The combi insert must be used if you wish to use – a pan with a smaller diameter base than the minimum given in the table. The combi insert ensures ...

  • Miele KM 2256 G - page 23

    – Use a pan lid whenever possible to minimise heat loss. – Cook with as little water as possible. – Cooking times are greatly reduced when using a pressure cooker. – Turn the flame down promptly to a lower setting when the pan has come to the boil. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. Energy ...

  • Miele KM 2256 G - page 24

    Thermoelectric safety ignition This appliance is fitted with a thermoelectric ignition safety device which cuts off the supply of gas to a burner if the flame goes out, for example if food has boiled over or if there is a sudden draught. ^ To use the burner again, turn the control clockwise to the " ß " position, and switch on as normal. ...

  • Miele KM 2256 G - page 25

    General notes , Do not use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit. The appliance should be cleaned regularly, preferably after each use. Allow it to cool down to room temperature before cleaning. To avoid water marks and limescale deposits, use a soft cloth to dr ...

  • Miele KM 2256 G - page 26

    Stainless steel surfaces Clean stainless steel surfaces using an Original Miele all purpose microfibre cloth or with a solution of warm water and a little washing-up liquid applied with a soft sponge. In the case of stubborn dried-on soiling, soak first. Finally, dry with a soft cloth. The Original Miele ceramic and stainless steel cooktop cleaner ...

  • Miele KM 2256 G - page 27

    Burners Do not clean any parts of the burner in a dishwasher. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Parts of the burner that cannot be removed should be wiped clean with a damp cloth only. The ignitor and ignition safety device should be ver ...

  • Miele KM 2256 G - page 28

    To assemble the auxiliary, normal and fast burners ^ Position the burner head r to the burner base u so that the ignition safety device s and the ignitor t extend through the respective burner head holes. ^ Finally, position the burner cap n ensuring that the locating tabs fit into the notches in the burner head. Important: Please ensure that the c ...

  • Miele KM 2256 G - page 29

    To assemble the wok-burner ^ Position the burner head r to the burner base u , so that the ignition safety device s and the ignitor t fit through the holes of the burner head. The lobe a on the burner cap must fit into the recess b of the burner head. The pin c on the burner head must fit into the recess d of the burner base. ^ Position the burner ...

  • Miele KM 2256 G - page 30

    Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. What to do if... ... the burner does not ignite after several attempts. ...

  • Miele KM 2256 G - page 31

    Miele branded cleaning and conditioning products are available for your appliance. These can be ordered via the internet at www.miele-shop.com (depending on country) or from Miele (see back cover). Original Miele ceramic and stainless steel cooktop cleaner 250 ml Removes heavy soiling, limescale deposits and light discolouration. Original Miele sta ...

  • Miele KM 2256 G - page 32

    Fit wall units and rangehood before fitting the cooktop to avoid damaging the surface. ~ This appliance must not be connected to a gas flue. It must be installed and connected in accordance with current installation regulations. ~ The room in which the gas cooktop is installed must be at least 51 m 3 in size with a door or window in it which can be ...

  • Miele KM 2256 G - page 33

    Safety clearance above the cooktop A minimum safety clearance must be maintained between the cooktop and the rangehood above it. See the rangehood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the rangehood, a minimum safety clearance of at least 760 mm above t ...

  • Miele KM 2256 G - page 34

    Before installing the appliance, check that the location provides the required clearances from combustible material and, if necessary, provide protection to adjacent surfaces as required by regulations. The minimum side clearance from a cooktop to a combustible surface* shall be a 300 mm horizontal distance from the periphery of any burner. The min ...

  • Miele KM 2256 G - page 35

    Appliance and building-in dimensions a Front b Building-in depth c Gas connection R 1/2 - ISO 7-1 d Electrical connection e Electronics housing 100 x 200 mm Max. building-in depth, including electronics housing, 134 mm KM 2256 35 ...

  • Miele KM 2256 G - page 36

    Installation ^ Make the worktop cut-out following the dimensions applicable. Remember to maintain the minimum safety distances (See "Safety clearances". ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture. ^ Feed the connection cable down through the cut-out. ^ Place the cooktop in the cut-o ...

  • Miele KM 2256 G - page 37

    General installation tips Sealant The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use any additional sealant (e.g. silicone) between the appliance and the worktop. This could cause difficulties if the appliance ever needs to be taken out for servicing and possibly result in damage ...

  • Miele KM 2256 G - page 38

    Appliance and building-in dimensions a Front b Building-in depth c Gas connection R 1/2 - ISO 7-1 d Electrical connection e Electronics housing 100 x 200 mm Max. building-in depth, including electronics housing, 139 mm f Stepped cut-out for granite or marble worktops Please take careful note of the inset diagram for the cut-out dimensions for grani ...

  • Miele KM 2256 G - page 39

    Flush fit cooktops are only suitable for installation in granite, marble, or tiled worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit cooktop. The internal width of the base unit must be at least 900 mm. This is to ensure that the underside of ...

  • Miele KM 2256 G - page 40

    Installation Granite and marble worktops a Worktop b Fixing bracket (the fixing brackets hold the lower section when the upper section of the cooktop is removed). c Cooktop d Gap As the cooktop and worktop cut-out may differ, the size of the gap d can vary. ^ Make the worktop cut-out following the dimensions applicable. Remember to maintain the min ...

  • Miele KM 2256 G - page 41

    Tiled worktops a Worktop b Fixing bracket (the fixing brackets hold the lower section when the upper section of the cooktop is removed). c Cooktop d Gap e Wooden frame 16 mm (to be provided on site)) As the cooktop and worktop cut-out may differ, the size of the gap d can vary. ^ Make the worktop cut-out following the dimensions applicable. Remembe ...

  • Miele KM 2256 G - page 42

    Appliance and building-in dimensions a Front b Building-in depth c Gas connection R 1/2 - ISO 7-1 d Electrical connection e Electronics housing 100 x 200 mm Max. building-in depth, including electronics housing, 139 mm f Stepped cut-out for granite or marble worktops Please take careful note of the inset diagram for the cut-out dimensions for grani ...

  • Miele KM 2256 G - page 43

    Flush fit cooktops are only suitable for installation in granite, marble, or tiled worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit cooktop. The internal width of the base unit must be at least 900 mm wide. This is to ensure that the undersid ...

  • Miele KM 2256 G - page 44

    Installation Granite and marble worktops a Worktop b Cooktop c Gap As the cooktop and worktop cut-out may differ, the size of the gap c can vary. ^ Make the worktop cut-out following the dimensions applicable. Remember to maintain the minimum safety distances (See "Safety clearances". ^ Feed the cooktop connection cable down through the c ...

  • Miele KM 2256 G - page 45

    Tiled worktops a Worktop b Cooktop c Gap d Wooden frame 7 mm (to be provided on site) As the cooktop and worktop cut-out may differ, the size of the gap c can vary. ^ Make the worktop cut-out following the dimensions applicable. Remember to maintain the minimum safety distances (See "Safety clearances". ^ Fix the wooden frame d 2 mm below ...

  • Miele KM 2256 G - page 46

    Secure the appliance as shown, using the fixings supplied. 20 mm worktop 30 mm worktop 40 mm worktop After installation Check that all the burners are operating correctly. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. On the highest setting, the flame must have a distinctive and ...

  • Miele KM 2256 G - page 47

    All electrical work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations. If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from Miele. For extra safety ...

  • Miele KM 2256 G - page 48

    Connection to the gas supply, or conversion from one type of gas to another should only be undertaken by an approved gas fitter, who is responsible for correct functioning of the appliance when installed. Every appliance should have its own isolating valve. The gas connection must be installed so that connection can be made either from inside or ou ...

  • Miele KM 2256 G - page 49

    The gas connection must be in accordance with national and local regulations. The relevant building regulations must also be observed. Natural gas / liquid gas During installation the gas connection must be positioned so that it is not adversely heated when the appliance is in operation. Pressure Test Point a . This is provided on the gas regulator ...

  • Miele KM 2256 G - page 50

    Nominal rating Gas type High setting Low setting MJ/h MJ/h Simmer burner NG ULPG 4 3.6 1.08 1.05 Standard burner NGs ULPG 6.2 5.5 1.08 1.05 High-speed burner NG ULPG 8 6.35 1.13 1.11 Extra high-speed burner NG ULPG 10 7.5 1.54 1.82 Dual Wok NG ULPG 15 15 5.99 5.89 Total NG ULPG 43.2 37.95 10.82 10.92 Nominal ratings for ULPG are based on propane ga ...

  • Miele KM 2256 G - page 51

    When converting to another type of gas, the main jets and the small jets on all burners have to be changed. Screw in the appropriate jets according to the type of gas. Refer to the below table. Jet table Main jet C Low setting jet C NG Simmer burner Standard burner High-speed burner Extra high-speed burner Dual Wok 0.90 1.10 (1B) 1.30 1.50 1.70 / 3 ...

  • Miele KM 2256 G - page 52

    Changing the jets Disconnect the gas cooktop from the electricity supply by switching it off at the socket and withdrawing the plug or by removing the mains fuse. To change the main jets Simmer, standard, high-speed and extra high-speed burners ^ Remove the pan support, burner cap n and burner head r . ^ Using an M7 socket spanner, unscrew the main ...

  • Miele KM 2256 G - page 53

    Wok burner ^ Remove burner covers op , burner ring q and burner head r . ^ Remove the controls. ^ Loosen screws w , and remove the cover plate. ^ Whilst counterholding it in place with an SW 13 spanner, unscrew the main jet anti-clockwise from its housing using an SW 10 spanner (see illustration). ^ Screw in the new main jet, once again using the s ...

  • Miele KM 2256 G - page 54

    To change the jet for the inner burner d Jet disc (main jet for the inner burner) e Air valve f Vent ^ Whilst counterholding it in place with an SW12 spanner, remove screw c from screw fitting b using an SW8 spanner. ^ Whilst counterholding it in place with an SW 12 spanner, remove screw fitting b from fitting a with another SW 12 spanner. ^ Take o ...

  • Miele KM 2256 G - page 55

    To check the first intake of air a Retaining screw b Air valve Gap X must measure: For natural gas: 13 mm For liquid gas: 13 mm If it doesn't: ^ Loosen the retaining screw, move the air valve, and tighten the retaining screw again. ^ Finally secure the jets against inadvertent loosening with sealing wax. ^ Re-assemble the cooktop in the revers ...

  • Miele KM 2256 G - page 56

    To change the small jets To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Pull off the controls. ^ Then lift off the upper section. Simmer, standard, high-speed and extra high-speed burners ^ Using a small screwdriver, unscrew small jet a in the gas fitting. ^ Pull out the ...

  • Miele KM 2256 G - page 57

    After changing the jets ^ Assemble the removed burner parts in the reverse order. ^ Check for leaks by operating the burner without the upper part of the cooktop in place (use a match to ignite the flame). ^ Remove the loose burner parts again. ^ Replace the upper part of the cooktop. ^ Screw the burner bases into place, and replace the other parts ...

  • Miele KM 2256 G - page 58

    The address and phone number of your nearest Miele office is given on the back page. The voltage and rated load are given on the data plate. Please quote this data, together with the model description and serial number when contacting Miele. Space in which to adhere the extra data plate supplied with the appliance. Ensure that the model number is t ...

  • Miele KM 2256 G - page 59

    59 ...

  • Miele KM 2256 G - page 60

    Alteration rights reserved / 0212 M.-Nr. 07 012 921 / 03 ...

Manufacturer Miele Category Stove

Documents that we receive from a manufacturer of a Miele KM 2256 G can be divided into several groups. They are, among others:
- Miele technical drawings
- KM 2256 G manuals
- Miele product data sheets
- information booklets
- or energy labels Miele KM 2256 G
All of them are important, but the most important information from the point of view of use of the device are in the user manual Miele KM 2256 G.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Miele KM 2256 G, service manual, brief instructions and user manuals Miele KM 2256 G. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Miele KM 2256 G.

Similar manuals

A complete manual for the device Miele KM 2256 G, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Miele KM 2256 G by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Miele KM 2256 G.

A complete Miele manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Miele KM 2256 G - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Miele KM 2256 G, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Miele KM 2256 G, that we can find in the current document
3. Tips how to use the basic functions of the device Miele KM 2256 G - which should help us in our first steps of using Miele KM 2256 G
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Miele KM 2256 G
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Miele KM 2256 G in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Miele KM 2256 G?

Use the form below

If you did not solve your problem by using a manual Miele KM 2256 G, ask a question using the form below. If a user had a similar problem with Miele KM 2256 G it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)