English dropdown-ico

Manual Freedom9 80

36 pages 0.58 mb
Download

Go to site of 36

Summary
  • Freedom9 80 - page 1

    freeV iew Power 80 8-port Power Management over IP USER’S MANUAL P/N: KPM-008M Rev . 1.2 ...

  • Freedom9 80 - page 2

    Copyright and T rademark Information This document contains propriet ary information that is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced, or translated into another language without express prior to written consent of Freedom9 Inc. © 2006 Freedom9 Inc., freeView Power and the freedom9 comp a ...

  • Freedom9 80 - page 3

    freeVie w Power 80 Use r Manual 1 T ABLE OF CONTENTS 1 GENERAL INFORMA TION ............................................................................................................ ...... 2 1.1 O VERVIEW ...................................................................................................................................... 2 1.2 S ...

  • Freedom9 80 - page 4

    2 1 General Information 1.1 Overview The freeView Power 80 allows you to remotely control the AC power for up to eight devices including servers, routers, modems and telephone networks. With the a bility to stack up to 16 units together , up to 128 devices can be controlled from a single interface. The freeVie w Power 80 supports several methods to ...

  • Freedom9 80 - page 5

    freeVie w Power 80 Use r Manual 3 1.4 Features The following are the main features for the freeV iew Power 80: • T urn any AC powered device on or off via IP network and phone. • Support turning on or off connected equipment manually using push buttons on the device. • Integrated 10/100BASE-T Ethernet port for connection to a TCP/IP network. ...

  • Freedom9 80 - page 6

    4 2 Inst allation 2.1 Inst allation Tip s When installing the freeV i ew Power 80, keep the following point s in mind: • Install the u nit in a cool and dry place. Refer to the specifications for det ails on permissible temperature and humidity ranges. • Install the unit in a location free from electromagnetic interference, vibrations, dust, an ...

  • Freedom9 80 - page 7

    freeVie w Power 80 Use r Manual 5 2.4 External Components The following diagrams show the front and rear p anels of the freeView Power 80 (Figures 2 and 3). Figure 2 – Front Panel Figure 3 – Rear Panel Phone Control Port Connecting the freeView Power 80 to an analog telephone port will allow the device to be controlled by dialing the telephone ...

  • Freedom9 80 - page 8

    6 Manual Switches The manual switches (A through H) are associated to the corresponding outlets in the back of the unit. Pressing and holding the button for three seconds will toggle the st ate between remote management (through the web and telnet interfaces) and local management. If a port is set to local management, pressing the button will turn ...

  • Freedom9 80 - page 9

    freeVie w Power 80 Use r Manual 7 freeView Power M2 Y ellow Red Green Description Off Of f On Power on Flashing On On System initializing On Off On Normal operation On Flashing On Connected to incorrect device Flashing Flashing On Writing dat a to flash memory LAN Port LED LED Color Description Green On: LAN connection speed is 100M Flashing: Dat a ...

  • Freedom9 80 - page 10

    8 3 Daisy Chaining 3.1 Daisy Chaining Up to sixteen units of the freeV iew Power 80 can be daisy chained to provide up to 128 managed power outlets. Each unit in the chain must be assigned a unique identification number . The default ID is 0. The following procedur e explains how to d aisy chain multiple units together: 1. Make sure that the T ermi ...

  • Freedom9 80 - page 11

    freeVie w Power 80 Use r Manual 9 15. Configure the third unit’ s ID number to “3” by logging into the web GUI, going to the RPM Setting menu, select “RPM00” under Select RPM, then select “03” beside “Address Change” then click “Apply”. After changing the unit’ s ID number , you will see the LED beside the number 3 light up ...

  • Freedom9 80 - page 12

    10 4 Managing the Device 4.1 SNMPIV The included SNMPIV software allows you to perform maintenance on the device ev en if you do not know the IP address of the unit. The SNMPIV sof tware also includes a st andard MIB which allows the unit to be monitored with third-p arty network man agement software. 4.1.1 Installing the Software T o install the s ...

  • Freedom9 80 - page 13

    freeVie w Power 80 Use r Manual 11 Figure 11 – Network Selection Network Selection By default, the software will automatically select a network interface card to use (wired or wireless). T o change the network interface to use, click “Network Selection” to display a list of available network interfaces (Figure 1 1), and select the one to use. ...

  • Freedom9 80 - page 14

    12 web or telnet interface passwords). T o set a password, enter the p assword into the “New password” field, and enter it again in the “Confirm p assword” field, and click “OK”. Remember to keep a record of this password, as it cannot be recovered if lost. Figure 13 – Advanced Tab On this tab, you can also set the ports used by the d ...

  • Freedom9 80 - page 15

    freeVie w Power 80 Use r Manual 13 Refresh Click the “Refresh” button to search the network for freeV iew Power 80 devices. 4.2 Web Interface T o access the web interface of the freeV iew Power 80, follow these steps: 1. Open a web browser (Internet Explorer 6.0 or higher is recommended). 2. Enter the IP address of t he unit into the address ba ...

  • Freedom9 80 - page 16

    14 Figure 16 – Main Menu Information: Provides information for the connected devices. Configuration: Allows for configuration of the network and devices settings. Log Information: Displays the log of events that occurred on the device. Device selection: Not currently used. Each category consist s of different p ages which are described in detail ...

  • Freedom9 80 - page 17

    freeVie w Power 80 Use r Manual 15 4.2.2 System Status The System S tatus page (Figure 17) displays the det ails of the system along with current network configuration settings. Figure 17 – System Status Page Firmware V ersion: Current version of firmware on the unit. Device Number: Unique identifier for the unit. System Name: The name given to t ...

  • Freedom9 80 - page 18

    16 4.2.3 RPM Status The RPM S tatus page (Figure 18) displays the current st atus of all of the power outlets, and allows you to turn outlets on and of f. Figure 18 – RPM Status Page If a power outlet is off, clicking on th e icon to the right of the outlet will turn it on. If a power outlet is on, clicking on the icon to the right of the outlet ...

  • Freedom9 80 - page 19

    freeVie w Power 80 Use r Manual 17 4.2.4 Network The Network page (Figure 19) allows you to change the net work settings of the device. Figure 19 – Network Page IP Address: The IP address of the unit used for web and telnet access. Subnet Mask: The subnet mask of the unit. Gateway: The gateway of the unit, required for accessing external mail ser ...

  • Freedom9 80 - page 20

    18 Obt ain an IP Address: Select whether the unit uses the IP address entered manually in the fields above, or obtains an IP address from a DHCP server . Primary DNS Server: The primary DNS server used for name resolution. Secondary DNS Server: The backup DNS server used for name resolution in the event the primary DNS server is unavailable. Connec ...

  • Freedom9 80 - page 21

    freeVie w Power 80 Use r Manual 19 4.2.5 SNMP The SNMP p age (Figure 20) allows you to manage the SNMP access right s to the device. By default, read/write access is allowed from any computer on the network. It is recommended to change this as soon as possible for security purposes. Figure 20 – SNMP Page System Name: The name given to the unit fo ...

  • Freedom9 80 - page 22

    20 the same community name can connect to the device. Permission: The permissions granted to users connecting using this interface (No Access, Read, Read/Write). Description: A brief description of the connecting users for the administrator ’s reference. Receiver IP Address: The IP address of the computer that should receive trap events. Communit ...

  • Freedom9 80 - page 23

    freeVie w Power 80 Use r Manual 21 4.2.6 Email The Email page (Figure 22) allows y ou to set up email addresses to receive event notifications and daily reports from the freeV iew Power 80. Figure 22 – Email Page Email Server: The SMTP server to use to send out emails. Sender ’ s Email Address: The email address to use in the “From” field f ...

  • Freedom9 80 - page 24

    22 Event s Selection: Clicking this button opens up a window where you can select exactly which traps to send (Figure 21 ). The events list ed under “ENV Events” require a freeV iew Power M2 module to be installed in the device. Email Address (Daily Report): The email address to send the daily report to. Send Email for Daily Report: Set to “Y ...

  • Freedom9 80 - page 25

    freeVie w Power 80 Use r Manual 23 4.2.8 Web/Telnet The Web/T elnet page (Figure 24) allows you to manage which users have access to the web and telnet interfaces on the freeV iew Power 80. Figure 24 – Web/Telnet Page User Name: The user name required to log into the unit. Password: The p assword required to log into the unit. Permission: The per ...

  • Freedom9 80 - page 26

    24 T ime Between Automatic Updates: Set the frequency the unit retrieves the current time from the time server (NO, 1 Hour , 3 Hours, 12 Hours, 1 Day , 10 Da ys, 30 Days). Primary Time Server: The IP address of the primary NTP server to retrieve the time from. Secondary Time Server: The IP address of the secondary NTP server to retrieve the time fr ...

  • Freedom9 80 - page 27

    freeVie w Power 80 Use r Manual 25 Phone Controllabe: Set whether the port can be configured through the telephone port. Control T ype: Set the method the freeView Power 80 uses to turn of f the outlet. • Safe shutdown: T urn off the port af ter the amount of time specified in the Power Off Delay field. • Safe reboot: T urn off the port af ter ...

  • Freedom9 80 - page 28

    26 For more details, refer to the document ation included with your operating system. T o allow sufficient time for a gra ceful system shutdown, it is recommended that the Power Of f Delay time be set to at least 120 seconds. 4.2.11 RPM Action The RPM Action page (Figure 28) list s the actions currently defined on the freeView Power 80 and allows y ...

  • Freedom9 80 - page 29

    freeVie w Power 80 Use r Manual 27 • Environmental Humidity Overrun: The environment sensor is reporting a humidity level above the maximum allowable humidity level (requires freeView Power M2 module). • Environment al Humidity Underrun: The environment sensor is reporting a humidity level below the minimum allowable humidity level (requires fr ...

  • Freedom9 80 - page 30

    28 RPM: Select the unit in the stack on which to t ake action. Outlet: Select the outlet in the unit on which to t ake action. Outlet Action: Set whether the outlet should be turned on or of f. Date: The date to activate the event. Can be set to a single date in “yyyy/mm/dd” format or occur on a daily or weekly basis. Time: The time in “hh:mm ...

  • Freedom9 80 - page 31

    freeVie w Power 80 Use r Manual 29 Figure 33 – Event Log Page The possible event s for the freeView Power 80 are: • RPM Connection Lost: One of the freeView Power 80 unit s in the stack is unavailable. • Outlet On: A specific outlet has been turned on. • Outlet Off: A specific outlet has been turned off. • Outlet Reboot: A specific outlet ...

  • Freedom9 80 - page 32

    30 Figure 34 – Starting Telnet 3. Once the T elnet connection has been made, the screen shown in Figure 35 will be displayed. Figure 35 – Telnet Connection 4. Enter the user name and password (Figure 36). The default value for both user name and password is nothing. It is highly recommended that these be changed as quickly as possible for secur ...

  • Freedom9 80 - page 33

    freeVie w Power 80 Use r Manual 31 Set SNMP MIB System Sets the MIB system group p arameters. Set SNMP Access Control Sets the Manager IP , Community , an d Access Permissions for SNMP access. Set SNMP T rap Notification Sets the IP address of computer which will receive the SNMP trap event s. Set UPS Properties Not used at this time. Set UPS Devic ...

  • Freedom9 80 - page 34

    32 4.4.1 Logging In T o manage the freeView Power 80 using a touch tone telephone, the unit must be connected to a live telephone line. Dial the phone number of the freeView Power 80. After three rings, the unit will answer with two short beeps. Enter your dial-in password followed by the “#” key . (The default password is 123456 789) If the pa ...

  • Freedom9 80 - page 35

    freeVie w Power 80 Use r Manual 33 4.4.3 Changing the Password T o change the password, follow these step s: • Enter the command “888#” after logging in. • Y ou will hear long beep s indicating that the device is ready to change your password. • Enter a new password using the following p attern: 888XXXXXXXXXX#. The password (XXXXXXXXXX) m ...

  • Freedom9 80 - page 36

    34 5 S pecifications 5.1 Product Specifications freeView Power 80 Programmable Power Outlets 8 Power Output 125V AC; 15A; 50~60 Hz (max) Power Source Input Ports 1 Power Source Input 125V AC; 15A; 50~60 Hz (max) Circuit Breakers 1 Push Switch 10/100 Ethernet Ports 1 RS-485 Chain Out Ports 1 RS-485 Chain In Ports 1 T elephone Ports 2 Power Requireme ...

Manufacturer Freedom9 Category Power Supply

Documents that we receive from a manufacturer of a Freedom9 80 can be divided into several groups. They are, among others:
- Freedom9 technical drawings
- 80 manuals
- Freedom9 product data sheets
- information booklets
- or energy labels Freedom9 80
All of them are important, but the most important information from the point of view of use of the device are in the user manual Freedom9 80.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Freedom9 80, service manual, brief instructions and user manuals Freedom9 80. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Freedom9 80.

Similar manuals

A complete manual for the device Freedom9 80, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Freedom9 80 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Freedom9 80.

A complete Freedom9 manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Freedom9 80 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Freedom9 80, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Freedom9 80, that we can find in the current document
3. Tips how to use the basic functions of the device Freedom9 80 - which should help us in our first steps of using Freedom9 80
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Freedom9 80
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Freedom9 80 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Freedom9 80?

Use the form below

If you did not solve your problem by using a manual Freedom9 80, ask a question using the form below. If a user had a similar problem with Freedom9 80 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)