English dropdown-ico

Manual Makita LXDT08Z

28 pages 1.18 mb
Download

Go to site of 28

Summary
  • Makita LXDT08Z - page 1

    1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES IMPORT ANT : Read Before Using. IMPORT ANT : Lire avant usage. IMPORT ANTE: Leer antes de usar . Cordless Imp act Driver T ournevis à Chocs sans Fil Atornillador de Imp acto Inalámbrico LXDT08 012780 ...

  • Makita LXDT08Z - page 2

    2 ENGLISH (Orig inal instruct ions) SPECIFICA TIONS Model LXDT08 Machine screw 4 mm - 8 mm (5/32 " - 5/16") S tandard bol t 5 mm - 14 mm (3/1 6" - 9/16") Capacities High tensile bo lt 5 mm - 12 mm (3/16" - 1 /2") No load speed (R PM) 0 - 2,500/min . Impact s per minute 0 - 3,200 Overall leng th 147 mm (5-7/8") Bat ...

  • Makita LXDT08Z - page 3

    3 13. Remove any adjusting key or wr ench before turning the power tool on. A wrenc h or a ke y l eft attached to a rota ting part of the pow er tool may result in person al injury . 14. Do not overreach. Keep proper footing and balance at all times. This enables b etter control of the power tool in unexpected situations. 15. Dress properl y. Do n ...

  • Makita LXDT08Z - page 4

    4 USD302-1 Symbols The followings sho w the symbols used for tool . ･ volts ･ direct current ･ no load speed ･ revolutions or recip rocation per minute ･ number of blow ENC007-7 IMPORT ANT SAFETY INSTRUCTIONS FOR BA TTER Y CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger , ( ...

  • Makita LXDT08Z - page 5

    5 FUNCTIONAL DESCRIPTION CAUTION : • Always be sure tha t the tool is sw itched off and the battery cartridge is removed before adjusting or checking fun ction on th e tool. Inst alling or remo ving battery cartridge 1 2 3 012781 CAUTION : • Always switch o ff the too l before inst alling or removing of the battery cartridge. • Hold the tool ...

  • Makita LXDT08Z - page 6

    6 Electric brake This tool is equipped w ith an electric brake. If the tool consistently fails to quickly stop af ter the switch trig ger is released, have the tool serviced at a Makit a service center . Lighting up the lamp CAUTION : • Do not look in the light or see the source o f light directly . 1 012783 Pull the sw itch trigger to light up t ...

  • Makita LXDT08Z - page 7

    7 • After insert ing the bit, ma ke sure that i t is firmly secured. If it comes out, do not use it. Hook 1 2 3 012787 The hook is convenient for temporaril y hanging the tool. This can be inst alled on either side of the tool. T o install the hook, in sert it into a groove in the tool housing on either si de and then secure it w ith a screw . T ...

  • Makita LXDT08Z - page 8

    8 The fastening torq ue is affected by a wide v ariety of factors including the following. Af ter fastening, alw ays check the torque w ith a torque wrench. 1. When the battery cartridge i s discharged almost completely , voltage will drop and the fastening torque will be reduced. 2. Driver bit or socke t bit Failure to use the correct si ze driver ...

  • Makita LXDT08Z - page 9

    9 FRANÇAIS (Mode d’empl oi original) SPÉCIFICA TIONS Modèle LXDT08 Vis de méc anique 4 mm - 8 mm (5/32 " - 5/16") Boulon stan dard 5 mm - 14 mm (3/1 6" - 9/16") Capacités Boulon à haute r ésistance 5 mm - 12 mm (3/1 6" - 1/2") Vitesse à v ide (T/MIN) 0 - 2 500 /min. Percussions p ar minute 0 - 3 200 Longueur ...

  • Makita LXDT08Z - page 10

    10 Sécurité personnelle 10. Restez al erte, a ttentif à vos mouvement s et faites pr euve de bon sens lorsq ue vous utilisez un outil éle ctriqu e. Évite z d'utilise r un outil électri que si vous êtes fatigué ou si vous avez pris une drogu e, de l'alcool ou un médicament. Un moment d'i nattention p endant l'ut ilisatio ...

  • Makita LXDT08Z - page 11

    11 batterie peut causer de s brûlures ou u n incendie. 27. Dans des conditions d'utilisation inadéquates de la batterie, il peut y avoir fuite d'électrolyte; évitez tout contac t avec ce liquide. En cas de contact accidentel, rincez avec beaucoup d’eau. Si le liquide pénètre dans vos yeux, il faut aussi consulter un médecin. L&ap ...

  • Makita LXDT08Z - page 12

    12 9. N'utili sez pas une batteri e si elle est endommagée. CONSERVEZ CE MODE D'EMPLOI. Conseils pour obtenir la d urée de service maximale de la batterie 1. Rechargez la batterie avant qu'elle ne soit complètement déchargée. Arrêtez toujours l'outil et rechargez la batterie quand vous remarquez que la puissance de l' ...

  • Makita LXDT08Z - page 13

    13 Système de protection de la batterie (batterie lithium-ion marquée d’u ne étoile) 1 012128 Les batteries lithiu m-ion marquées d’une étoile son t équipées d’un système de prote ction. Ce système coupe automatiquement l’alimentatio n de l’outil pour augmenter la durée de vie de l a batterie. L'outil s’arrête automatiq ...

  • Makita LXDT08Z - page 14

    14 rotation av ant l'arrêt de l'outil, v ous risquez de l'endommager . • Lorsque vous n'utilisez p as l'outil, placez toujours le levier inverseur en position neutre. ASSEMBLAGE AT T E N T I O N : • Assurez-vous toujo urs que l' outil est hors tension et que sa batterie est re tirée avant d'ef fectuer tout t ...

  • Makita LXDT08Z - page 15

    15 120 100 80 60 40 20 0 1.0 2.0 3.0 M14 M12 M10 M8 (M14) (M12) (M10) (M8) Boulon standard N m Couple de serrage T emps de serrage (S) Couple de serrage adéquat (kgf cm) (1224) (1020) (816) (612) (408) (204) 006255 120 (1224) 100 (1020) 80 (816) 60 (612) 40 (408) 20 (204) 0 1.0 2.0 3.0 M12 M10 M8 (M12) (M10) (M8) N m Couple de serrage T emps de se ...

  • Makita LXDT08Z - page 16

    16 Si vous désirez ob tenir plus de dé tails concernant ces accessoires, veuillez con tac ter le centre de serv ice après-vente Makit a le plus près. • Forets de vis • Crochet • Embouts à douille • Mallette de transpo rt en plastique • Chargeur et batterie authentique s Makita • Rallonge d'embout • Protection de la batterie ...

  • Makita LXDT08Z - page 17

    17 ESP AÑOL (Instrucciones originales) ESPECIFICACIONES Modelo LXDT08 T ornillo de máquina 4 mm - 8 mm (5/32" - 5/16" ) T ornillo estándar 5 mm - 14 mm (3/16" - 9/16") Capacidades T ornillo de alta tracción 5 mm - 12 mm (3/16" - 1/2" ) V elocidad sin carga (r .p.m.) 0 - 2 500 r/min Impactos por minuto 0 - 3 200 Lon ...

  • Makita LXDT08Z - page 18

    18 alimentador protegido con interruptor de circuito de falla e n tierra (ICFT). El uso de un ICFT reduce el riesgo de descarga e léctrica. Seguridad personal 10. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice la herramienta eléctrica cuando esté cansad ...

  • Makita LXDT08Z - page 19

    19 actuar creando una conexión entre las terminales de la batería. Cerrar el circuito las terminales de la batería puede causar quemaduras o incendios. 27. En condiciones abusivas, podrá escapar líquido de la bate ría; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda méd ...

  • Makita LXDT08Z - page 20

    20 9. No use una batería dañada. GUARDE EST AS INSTRUCCIONES. Consejos para alargar al máximo la v ida útil de la batería 1. Cargue el cartucho de batería antes de que se descargue completamente. Pare siempre la operación y cargue el cartucho de batería cuando note menos potencia en la herramient a. 2. No cargue nunca un cartucho de baterí ...

  • Makita LXDT08Z - page 21

    21 Sistema de protección de b atería (batería de ión de litio con marca de estrell a) 1 012128 Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección. Este sistema corta en forma automática el sumini stro de energía a la herram ienta para prolongar la vida ú til de la batería. La herramienta ...

  • Makita LXDT08Z - page 22

    22 PRECAUCIÓN: • Confirme siempre la dirección de giro antes de la operación. • Utilice el conmu tador de invers ión s olamente después de qu e la herramien ta haya parado completamen te. Si cambia la direcc ión de giro ante s de que la herram ienta haya parado p odrá dañar la. • Cuando no esté utilizando la herramienta, ponga siempr ...

  • Makita LXDT08Z - page 23

    23 1 012912 El Par T orsional apropiado podrá variar dependien do del tipo o tamaño del to rnillo/perno, el material de la pieza de trabajo a apret ar , etc. La relación entre el par torsional y el tiempo de apriete se mue stra en las figuras. 120 100 80 60 40 20 M14 M12 M10 M8 (M14) (M12) (M10) (M8) T ornillo estándar N m Par de fuerza de apri ...

  • Makita LXDT08Z - page 24

    24 Para mantener la SEGURI DAD y FIABILIDAD del producto, las rep araciones, y cualquier otra tarea de mantenimiento o ajuste de berán ser realizadas en Centros de Serv icio Autorizados por Makita, empleando siempre repuestos Makit a. ACCESORIOS OPCIONALES PRECAUCIÓN: • Estos accesorios o adi tamentos (incluidos o no) están recomenda dos para ...

  • Makita LXDT08Z - page 25

    25 ...

  • Makita LXDT08Z - page 26

    26 ...

  • Makita LXDT08Z - page 27

    27 ...

  • Makita LXDT08Z - page 28

    28 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry pro ...

Manufacturer Makita Category Cordless Drill

Documents that we receive from a manufacturer of a Makita LXDT08Z can be divided into several groups. They are, among others:
- Makita technical drawings
- LXDT08Z manuals
- Makita product data sheets
- information booklets
- or energy labels Makita LXDT08Z
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita LXDT08Z.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita LXDT08Z, service manual, brief instructions and user manuals Makita LXDT08Z. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita LXDT08Z.

Similar manuals

A complete manual for the device Makita LXDT08Z, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita LXDT08Z by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita LXDT08Z.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita LXDT08Z - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita LXDT08Z, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita LXDT08Z, that we can find in the current document
3. Tips how to use the basic functions of the device Makita LXDT08Z - which should help us in our first steps of using Makita LXDT08Z
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita LXDT08Z
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita LXDT08Z in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita LXDT08Z?

Use the form below

If you did not solve your problem by using a manual Makita LXDT08Z, ask a question using the form below. If a user had a similar problem with Makita LXDT08Z it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)