English dropdown-ico

Manual Heat & Glo LifeStyle MTL-INSERT

39 pages 1.96 mb
Download

Go to site of 39

Summary
  • Heat & Glo LifeStyle MTL-INSERT - page 1

    1 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Model: MTL-Insert • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch. Do not use any phone in your building. - ...

  • Heat & Glo LifeStyle MTL-INSERT - page 2

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: ____________________ Dealership purchased from: _______ ...

  • Heat & Glo LifeStyle MTL-INSERT - page 3

    3 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. BTU Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. High Altitude Installations . . . . . . . . . . . . . . . . ...

  • Heat & Glo LifeStyle MTL-INSERT - page 4

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 4 Note : T o assure top performance, safety and ef fi ciency , inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions. Not e: This installation must c onform wi th local c odes. In the absenc e of local c ode ...

  • Heat & Glo LifeStyle MTL-INSERT - page 5

    5 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Heat & Glo gas inserts are designed for recessed installa- tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes. Prior to installing the gas insert: • Have th ...

  • Heat & Glo LifeStyle MTL-INSERT - page 6

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 6 T OP VIEW A C B 3 3 F ireplace Size Requirements A. Minimum Fireplace Opening Minimum fi replace opening requirements are shown in Figure 3.1. • The fi rebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built fi rebox in order t ...

  • Heat & Glo LifeStyle MTL-INSERT - page 7

    7 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 B. Clearances Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Fire Risk. • Locate and install appliance to all clearance speci fi cations in manual. Fire Risk. Odor Risk. • Clearance to combustible material under the insert is 1/4 inch (0.6 cm). • Use leveli ...

  • Heat & Glo LifeStyle MTL-INSERT - page 8

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 8 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.1 speci fi es minimum vent heights for various pitched roofs. Roof Pitch H (Min.) Ft. Fl ...

  • Heat & Glo LifeStyle MTL-INSERT - page 9

    9 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 CAUTION ALL vent speci fi cations MUST be followed. • This product is tested and listed to these speci fi cations. • Appliance performance will suffer if speci fi cations are not followed. EXHAUST VENT PIPE TERMINA TION CAP ADAPTOR INSULA TION SEAL INLET VENT AIR PIPE MIN. = 14FT ...

  • Heat & Glo LifeStyle MTL-INSERT - page 10

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s speci fi cation. • Local building codes required by authority having jurisdiction. • NFPA 211 Prepare ...

  • Heat & Glo LifeStyle MTL-INSERT - page 11

    11 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 A. V enting Components 7 7 Installing V ent P ipe and Appliance The vertical vent termination system installed on this model includes: • One length of 3-inch fl exible vent pipe for combustion air (included with vent kit). Pipe will be either a 4-foot or 30-foot section depending on ...

  • Heat & Glo LifeStyle MTL-INSERT - page 12

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 12 Figure 7.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 7.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top. C. Placing, Securing and Leveling the Appliance ? ...

  • Heat & Glo LifeStyle MTL-INSERT - page 13

    13 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 D. Installing T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.3) . Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........1.25* Over 7/12 to 8/12 ..........1.5* Over 8/12 to 9/12 ..... ...

  • Heat & Glo LifeStyle MTL-INSERT - page 14

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 14 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. • Check all fi ttings and connections of applianc ...

  • Heat & Glo LifeStyle MTL-INSERT - page 15

    15 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.L. Listed gas appliances are tested and approved without requiring changes for eleva ...

  • Heat & Glo LifeStyle MTL-INSERT - page 16

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 16 A. Wiring the Appliance 9 9 Elect rical Infor mation Note : This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code, CSA C221.1. ON/OF ...

  • Heat & Glo LifeStyle MTL-INSERT - page 17

    17 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 B. Optional Junction Box Installation Figure 9.2 Optional Junction box installation JUNCTION BOX SIDEW ALL JUNCTION BOX ACCESS SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower or remote. • Plug the cord into a convenient outlet. ...

  • Heat & Glo LifeStyle MTL-INSERT - page 18

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 18 Figure 9.3 Fan/Rheostat Wire Diagram (Optional) JUNCTION BOX V ARIABLE SPEED CONTROL TEMPERA TURE SENSOR SWITCH WHT GRN BLK BLK 1 10-120 V AC BLOWER BLOWER RECEPT ACLE BLK BLK BLK BLK WHT GROUND WHT BLK BLK BLK FA N TEMPERA TURE SENSOR SWITCH SPEED CONTROL (RHEOST A T) JUNCTION BOX GROU ...

  • Heat & Glo LifeStyle MTL-INSERT - page 19

    19 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. 1 0 10 Fin ishing Figure 10 .1 Clearances to Mantels or other C ...

  • Heat & Glo LifeStyle MTL-INSERT - page 20

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 20 Figure 1 1.1 Placement of Embers 1 1 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . C. ...

  • Heat & Glo LifeStyle MTL-INSERT - page 21

    21 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Log Set Assembly: LOGS-SXT E. Positioning the Logs CAUTION: Logs are fragile! Carefully remove the logs from the packaging. If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately , refer to the following instructions. ...

  • Heat & Glo LifeStyle MTL-INSERT - page 22

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 22 LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner . The slot on the right side of log #3 fi ts over the bar grate. LOG #2 (SRV349-702): Position log #2 by locating its slot over the tab on the front left of the burner . The slot of ...

  • Heat & Glo LifeStyle MTL-INSERT - page 23

    23 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 LOG #6 (SRV349-706): Position the "Y" end of log #6 into the cutout on log #4 and its opposite end into the groove on log #2. LOG #5 (SRV327-705): Rest log #5 in the cutouts on both log #1 and log #3 as shown. The front edge of log #1 should be at the top of the hole when look ...

  • Heat & Glo LifeStyle MTL-INSERT - page 24

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 24 Figure 1 1.5 Glass Assembly F . Glass Assembly Removing Glass Assembly There are two glass latches on bottom of the glass as- sembly . • T o release glass assembly , pull latch forward and allow to retract away from glass assembly . • Remove glass assembly after the bottom two latch ...

  • Heat & Glo LifeStyle MTL-INSERT - page 25

    25 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before operating this appliance have a qualified ...

  • Heat & Glo LifeStyle MTL-INSERT - page 26

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 26 B. Lighting Appliance Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Close c ...

  • Heat & Glo LifeStyle MTL-INSERT - page 27

    27 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1. D. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it pro ...

  • Heat & Glo LifeStyle MTL-INSERT - page 28

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 28 E. Frequently Asked Questions Fire Risk. High T emperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air . • Do NOT place combustible items on top of or in front of appliance. • Keep furniture, draperies away from appliance. S ...

  • Heat & Glo LifeStyle MTL-INSERT - page 29

    29 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the diagn ...

  • Heat & Glo LifeStyle MTL-INSERT - page 30

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 30 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than ...

  • Heat & Glo LifeStyle MTL-INSERT - page 31

    31 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 1 4 14 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection by ...

  • Heat & Glo LifeStyle MTL-INSERT - page 32

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 32 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary . 3. V erify no obstructions to air fl ow through ...

  • Heat & Glo LifeStyle MTL-INSERT - page 33

    33 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Figure 15.1 Appliance Dimensions 1 5 15 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Fo r framing dimensions and clearances refer to Section 3. A C B ELECTRICAL ACCESS GAS INLET D E F G H I L N K J M O P Q R S U T ...

  • Heat & Glo LifeStyle MTL-INSERT - page 34

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 34 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 15.2) LINK-DV -30B or (LINK-DV -30) : Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter . LINK-DV4-30B or (LINK-DV4-30) : Masonry 3 inch fl ex liner ...

  • Heat & Glo LifeStyle MTL-INSERT - page 35

    35 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 Service Parts Diagram MTL-INSERT C. Service Parts Beginning Manufacturing Date: Oct. 2007 Ending Manufacturing Date: ______ Part number list on following page. Log Set Assembly 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ...

  • Heat & Glo LifeStyle MTL-INSERT - page 36

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 36 Service Parts Diagram MTL-INSERT Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at ...

  • Heat & Glo LifeStyle MTL-INSERT - page 37

    37 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 MTL-INSERT Service Parts V alve Assembly Parts List Beginning Manufacturing Date: Oct. 2007 Ending Manufacturing Date: ______ Standing Pilot V alve Assembly 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for you ...

  • Heat & Glo LifeStyle MTL-INSERT - page 38

    Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 38 D. Limited Lifetime W arranty © 2007 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY HEA T & GLO GAS APPLIANCE PRODUCTS 060-981E 10/07 BASIC ONE-YEAR W ARRANTY . HEA T & GLO, a brand of HEAR TH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, ...

  • Heat & Glo LifeStyle MTL-INSERT - page 39

    39 Heat & Glo • MTL-Insert • 2145-900 Rev . D • 3/08 E. Contact Information - NOTES - ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ___________ ...

Manufacturer Heat & Glo LifeStyle Category Stove

Documents that we receive from a manufacturer of a Heat & Glo LifeStyle MTL-INSERT can be divided into several groups. They are, among others:
- Heat & Glo LifeStyle technical drawings
- MTL-INSERT manuals
- Heat & Glo LifeStyle product data sheets
- information booklets
- or energy labels Heat & Glo LifeStyle MTL-INSERT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Heat & Glo LifeStyle MTL-INSERT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Heat & Glo LifeStyle MTL-INSERT, service manual, brief instructions and user manuals Heat & Glo LifeStyle MTL-INSERT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Heat & Glo LifeStyle MTL-INSERT.

Similar manuals

A complete manual for the device Heat & Glo LifeStyle MTL-INSERT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Heat & Glo LifeStyle MTL-INSERT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Heat & Glo LifeStyle MTL-INSERT.

A complete Heat & Glo LifeStyle manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Heat & Glo LifeStyle MTL-INSERT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Heat & Glo LifeStyle MTL-INSERT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Heat & Glo LifeStyle MTL-INSERT, that we can find in the current document
3. Tips how to use the basic functions of the device Heat & Glo LifeStyle MTL-INSERT - which should help us in our first steps of using Heat & Glo LifeStyle MTL-INSERT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Heat & Glo LifeStyle MTL-INSERT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Heat & Glo LifeStyle MTL-INSERT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Heat & Glo LifeStyle MTL-INSERT?

Use the form below

If you did not solve your problem by using a manual Heat & Glo LifeStyle MTL-INSERT, ask a question using the form below. If a user had a similar problem with Heat & Glo LifeStyle MTL-INSERT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)