English dropdown-ico

Manual Lanier LW 210

72 pages 1.03 mb
Download

Go to site of 72

Summary
  • Lanier LW 210 - page 1

    y our doc ument ma nage ment pa r tner Operating Instructions L W 210 L W 210 L W 210 L W 210 Wide Format Copier ...

  • Lanier LW 210 - page 2

    A1748607 -., I In accordance with ISO Standard 7001, this machine uses the following symbols I for the main switch: I means POWER -- ON. 0 means POWER OFF. Q) means STAND BY. I For good copy q uality, Ricoh recommends that you use genuine Ricoh toner. I Ricoh shall not be responsible for any damage or expense that may result from the use of parts o ...

  • Lanier LW 210 - page 3

    INTRODUCTION This copier is a desktop plain paper copier carefully manufactured to exacting standards of high performance. It consistently yields high contrast copies with a superior finish. This manual contains detailed instructions on the operation and maintenance of this copier. To get maximum versatility from this copier, all operators should c ...

  • Lanier LW 210 - page 4

    R WARNINGS: m • Only connect the copier to the power source described on the inside front cover of this manual. Avoid multi-writing as it could cause an electric shock or a fire. • Avoid using an extension cord. Make sure the wall outlet is near the copier and freely accessible so that in event of an emergency it can be unplugged easily. m • ...

  • Lanier LW 210 - page 5

    R Cautions: o • After you move the copier, lock it in position with the caster fixture. If you do not, the copier might move or fall causing personal injury. m • Do not lean on the original tray or copy table otherwise they might fall causing personal injury. r • When you move the copier, unplug the power cord form the wall outlet to avoid fi ...

  • Lanier LW 210 - page 6

    ...

  • Lanier LW 210 - page 7

    TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i COPIER EXTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operation Panel . . . . . . . . . . . . . . . . . . . . . ...

  • Lanier LW 210 - page 8

    WHAT TO DO IF SOMETHING GOES WRONG WHEN THE "WAIT" INDICATOR IS LIT . . . . . . . . . . . . . . . . . . . . 30 IF YOUR COPIER DOES NOT OPERATE AS YOU WANT . . . . . 31 WHEN A OR x IS LI T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 When A and Are Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 W ...

  • Lanier LW 210 - page 9

    COPIER EXTERIOR Main Unit Manual Feed Set sheet paper here. Original cover Lower copy guide Copies are delivered here when the lower copy exit is selected. Paper Path section Upper copy guide Copies are delivered here when the upper copy exit is selected. 1st/2nd roll feeder Set roll paper here. Front/rear delivery switch lever Switches between the ...

  • Lanier LW 210 - page 10

    Operation Panel Indicator Panel Copy Exit key Switches the direction in which copies are delivered. → See page 10. Edge indicators Displays the margin settings. Cut Select key Switches the paper cut type. → See page 14. Paper Select key Selects the paper feed type. → See page 22. Paper Size key Switches the paper cut size in the paper feed di ...

  • Lanier LW 210 - page 11

    COPYING BASIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended Originals . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Switching the Fusing Temperature . . . . . . . . . . . . . . . . . . 7 Setting the Number of Copie ...

  • Lanier LW 210 - page 12

    BASIC This section describes how to set the functions and recommended originals and paper. Recommended Originals S When you copy the following originals, use the carrier sheet (option) to set them: ☞ See page 62, "OTHER OPTIONS" • Thin originals • Torn originals • Folded originals • Curled originals • Pasted originals S You ca ...

  • Lanier LW 210 - page 13

    2 Remove the upper copy guide. 3 Insert the original face down into the table along the size indication. ✏ Do not release the original until it is fed into the copier. S Set a leading margin of 5 mm, 0.2" or more when you copy an original whose leading edge has a large solidly-shaded area. ☞ See page 11, "Setting a Leading/Trailing Ed ...

  • Lanier LW 210 - page 14

    S When you make a copy on a non-standard size of paper, set the paper on the manual feed table. S Paper of about the thickness of 51 to 134 g/m 2 , 14 lb to 36 lb is suitable for this copier. ✏ Do not use the following paper. Otherwise, a paper jam might occur. • Bent, folded, or creased paper • Torn paper • Perforated paper • Non-smooth ...

  • Lanier LW 210 - page 15

    Switching the Fusing Temperature When you make a copy on translucent paper or transparent film, switch the fusing unit temperature to stabilize toner fusing. S If you make a copy in the condition unsuitable for copy paper, the copy might be creased or a part of the image might not be copied. S Turn on the "HIGH" indicator for translucent ...

  • Lanier LW 210 - page 16

    Setting the Number of Copies (Repeated Copying) Repeated copying means to make two or more copies of one original. This function allows you to make up to 10 copies in the size of 1,200 × 914 mm, 49" × 36" to B5 K . S In repeated copying, the image might be copied slantly depending on the original size, type, and condition (e.g., curl, w ...

  • Lanier LW 210 - page 17

    Adjusting Copy Density The "Auto Image Density" function means to adjust copy density automatically to mask out dark backgrounds of an original. If you cannot make copies as you want with the Auto Image Density function, adjust the copy density manually. S When you turn on the copier, the "Auto Image Density" indicator lights. S ...

  • Lanier LW 210 - page 18

    Switching the Copy Exit This function switches the copy exit direction to the upper or lower according to the copy paper size. S Select the lower copy exit when copying onto A0, 36" × 48" K or A1, 24" × 36" K paper. If you use the upper copy exit to copy onto these paper, delivered copies might remain inside the copier causing ...

  • Lanier LW 210 - page 19

    2 When you take copies out of the rear side of the copier in the lower copy exit mode, pull out the delivery switch levers until they stop, as shown in the figure on the right. ✏ You must pull out both levers at the same time. When you take copies out of the front side of the copier in the lower copy exit mode, press the delivery switch levers un ...

  • Lanier LW 210 - page 20

    Setting a Leading/Trailing Edge Margin You can set a margin at the leading or trailing edge of the copy. You can also make a copy using a narrower margin than that on the original. S You can set up to ± 99 mm, ± 4.0" margin in 1 mm, 0.1" steps at either the leading or trailing edge. S You can set a trailing margin only when you select t ...

  • Lanier LW 210 - page 21

    2 Press the + and - keys to specify a leading edge margin. ✏ Press the + key to increase the margin width and - to decrease the width. ✏ If you enter a wrong value, press the Clear/Stop key and reenter a correct value. 3 Press the Edge Margin key. The specified value goes on. The "Trailing Edge" indicator flashes when the "Synchr ...

  • Lanier LW 210 - page 22

    COPYING ONTO ROLL PAPER You can copy onto roll paper in the following three ways: synchro cutting, preset cutting, and variable cutting. S If roll paper is damp, cut it in about 1,000 mm, 39.4" immediately before copying. ☞ See page 41, "Cutting the Paper Automatically/Manually" Synchro Cutting This function cuts roll paper automat ...

  • Lanier LW 210 - page 23

    3 Insert the original lightly along the original guide. The copier starts copying. ✏ Do not release the original until it is fed into the copier. Preset Cutting This function cuts roll paper in a selected length. The paper is cut regardless of the original size. S The preset cut length is divided into five types. Depending on the roll width, it i ...

  • Lanier LW 210 - page 24

    Inch version: Roll width Preset length Paper size and direction 36" 48" E K 24" D L 24" 36" D K 18" C L 18" 24" C K 12" B L 12" 18" B K  9" 12" A K  1 Press the Cut Select key to display a length of the "Preset Cut". 2 Set the original guide to match the original ...

  • Lanier LW 210 - page 25

    3 Insert the original lightly along the original guide. The copier starts copying. ✏ Do not release the original until it is fed into the copier. Variable Cutting This function cuts roll paper in a length you specify. S The variable cut can handle the cut length from 245 to 3,600 mm, 9.6" to 142". 1 Press the Cut Select key to turn on t ...

  • Lanier LW 210 - page 26

    3 Set the original guide to match the original width and direction. 4 Insert the original lightly along the original guide. The copier starts copying. ✏ Do not release the original until it is fed into the copier. COPYING ONTO ROLL PAPER 18 COPYING ...

  • Lanier LW 210 - page 27

    PARTIAL COPYING The Partial Copy function copies only a part of an original. This function specifies the start and end points in the original feed direction. S The Partial Copy function cannot apply to originals having a length of less than 245 mm, 9.6" in the paper feed direction. S The Partial Copy function cannot be used in the rear table. ...

  • Lanier LW 210 - page 28

    3 Press the Partial Copy key when the leading edge of the area to be copied comes to the position where it is covered with the origin- al table cover. The indicator on the Partial Copy key lights. ✏ If you do not press the Partial Copy key, the original is deli- vered without partial copying. 4 Press the Partial Copy key when the trailing edge of ...

  • Lanier LW 210 - page 29

    SAMPLE COPYING The Sample Copy function copies an original in 245 mm, 9.6" from its leading edge in the paper feed direction. This allows you to check the copy condition of the current settings in advance. 1 Press the Sample Copy key. The indicator on the Sample Copy key is lit. ✏ When you press the Sample Copy key again, you can cancel samp ...

  • Lanier LW 210 - page 30

    PAPER TYPE/ROLL WIDTH ENTRY FUNCTION This function allows you to store the paper type and roll width for a selected paper feeder. When you change the paper feeder to the specified one, the paper type and roll width are set to the stored values. 1 Press the Paper Select key until your desired paper feeder indica- tor blinks. The paper feeder indicat ...

  • Lanier LW 210 - page 31

    5 Press the Fusing Temperature key to select the paper type. 6 Press the Enter key. The above settings are stored. ✏ If you do not want to store the settings, press the Clear Modes key. PAPER TYPE/ROLL WIDTH ENTRY FUNCTION COPYING 23 ...

  • Lanier LW 210 - page 32

    USING THE PROGRAM FUNCTION The Program function allows you to store a collection of copy settings as programs 1 to 9 and switch them as needed. Programming a Collection of Copy Settings 1 Press the Program key. The indicator on the Program key blinks. The copy counter displays the current program number. 2 Use the and keys to select a program numbe ...

  • Lanier LW 210 - page 33

    4 Specify values for each setting. You can store the following settings with the Program function. For the way to specify values, see the corresponding pages. • Sample copying → See page 21. • Partial copying (The start and end points cannot be stored) → See page 19. • Paper feeder → See page 22. • Copy exit → See page 10. • Margi ...

  • Lanier LW 210 - page 34

    Recalling Programmed Settings 1 Press the Program key . The indicator on the Program key blinks. 2 Use the and keys to select a program number. 3 Press the Program key. The Program key lights and the programmed settings are recalled. ✏ When you press the Program key again, you can cancel the program recall. USING THE PROGRAM FUNCTION 26 COPYING ...

  • Lanier LW 210 - page 35

    COPYING WITH MANUAL FEED When you make a copy with manual feed, you need not replace paper even if the required size or type of paper is not set in the copier. S Set a sheet of paper at a time on the manual feed table. S You cannot use the repeated copying function during manual copying in the default setting. To change the setting, contact your se ...

  • Lanier LW 210 - page 36

    3 Set the copy paper guide to match the paper width and direction (the copy paper guide is an option). 4 Insert the paper lightly along the copy paper guide (the copy paper guide is an option). ✏ Do not release the paper until it is fed into the copier. 5 Set the original guide to match the original width and direction. 6 Insert the original ligh ...

  • Lanier LW 210 - page 37

    WHAT TO DO IF SOMETHING GOES WRONG WHEN THE "WAIT" INDICATOR IS LIT . . . . . . . . . . . . . . . . . 30 IF YOUR COPIER DOES NOT OPERATE AS YOU WANT . 31 WHEN A OR x IS LI T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 When A and Are Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 When x and Are Lit . . . . . ...

  • Lanier LW 210 - page 38

    WHEN THE "WAIT" INDICATOR IS LIT You cannot start copying while the "Wait" indicator is lit. Check indicators on the operation panel and take action according to the instructions shown below. S If no indicator is lit on the operation panel, check that the power is on. Indication Corrective action x is lit. Remove the misfed pape ...

  • Lanier LW 210 - page 39

    IF YOUR COPIER DOES NOT OPERATE AS YOU WANT The following table shows the causes of problems and the corrective actions when your copier does not operate as you want. If the same problem remains even when you take the corresponding action, contact your service representative. Dirty Copies Cause Corrective action The copy density is too dark. Reduce ...

  • Lanier LW 210 - page 40

    Waved Copies Cause Corrective action The fusing temperature is not appropriate. Switch the fusing temperature according to the paper type. → See page 7. The paper texture flow di- rection is not appropriate. Use paper of the appropriate texture flow direction. Inappropriate copy paper is used. Use only recommended paper. → See page 5. Creased C ...

  • Lanier LW 210 - page 41

    WHEN A OR x IS LIT A paper jam has occurred. The corrective action varies depending on the location having the misfed paper. Remove the paper according to the corre- sponding instruction shown below. ✏ Be sure to remove the paper completely without tearing it. If a piece of the paper remains inside the copier, the paper jam might recur or another ...

  • Lanier LW 210 - page 42

    When A and Are Lit 1 Open the original cover. 2 Remove the original. ✏ If you can remove it, go to 6 . 3 If you cannot remove the original, open the original table. 4 Remove the original. WHEN A OR x IS LIT 34 WHAT TO DO IF SOMETHING GOES WRONG ...

  • Lanier LW 210 - page 43

    5 Close the original table until it clicks. ✏ When you close the original table, hold its left and right sides. 6 Close the original cover. When x and Are Lit 1 Open the image producing unit by pulling up the left and right knobs. ✏ You must open this unit com- pletely. 2 Remove the misfed paper. WHEN A OR x IS LIT WHAT TO DO IF SOMETHING GOES ...

  • Lanier LW 210 - page 44

    3 If you cannot remove the paper, open the rear cover. 4 Remove the paper. ✏ You should remove it from the front side of the copier. 5 Close the rear cover. 6 Close the image producing unit until it clicks. ✏ Close this unit completely. Otherwise, a paper misfeed might recur. WHEN A OR x IS LIT 36 WHAT TO DO IF SOMETHING GOES WRONG ...

  • Lanier LW 210 - page 45

    When Is Lit 1 Pull out the roll feeder. ✏ Pull out the feeder until it stops. 2 If a paper misfeed occurs at the third roll, open the third roll feeder cover. 3 Remove the roll paper gently. ✏ When you remove the roll pa- per, it is recommended to roll back the paper than to pull it out. ✏ If the paper edge is torn or folded, cut it with a sc ...

  • Lanier LW 210 - page 46

    WHEN C IS LIT The roll feeder runs out of paper or the roll paper is not set properly. Set paper in the roll feeder. S Set roll paper for each roll. S When you remove roll paper from a paper spool or set new paper on a spool, place the spool horizontally on a flat surface. S Even if the roll feeder runs out of paper during repeated copying, you can ...

  • Lanier LW 210 - page 47

    4 Remove the roll paper while pressing the paper release lever on the right edge of the paper spool as shown in the figure on the right. 5 Set new paper on the paper spool making sure that the paper is rolled in the proper direction. ✏ While pressing the paper re- lease lever, align the paper with the size indication on the paper spool. 6 Set the ...

  • Lanier LW 210 - page 48

    7 Feed the paper under the paper feed roller until it stops. Then turn the knob until the paper edge extrudes from under the cover by about 150 mm, 5.9" (cover closed). ✏ If the roll paper is damp, rotate the knob so that the paper edge extrudes from under the cover by about 1,000 mm, 39.4" (cover closed). 8 For the third roll, feed the ...

  • Lanier LW 210 - page 49

    Cutting the Paper Automatically S You can cut roll paper either manually or automatically. S When removing any jammed paper, cut the paper manually. When loading new paper, you can cut it both manually and automatically. 9 Close the roll feeder gently. a Press the Roll Edge Cut key. b Remove the cut paper from the roll feeder. WHEN C IS LIT WHAT TO ...

  • Lanier LW 210 - page 50

    Cutting the Paper Manually 9 Cut the roll paper with the paper cutter and rotate the knob to roll back the paper in about 50 mm, 2.0". ✏ Move the paper cutter once in either the left or right direc- tion. ✏ When you cut the roll paper with the paper cutter, rotate the knob to roll back the paper slightly. a Close the roll feeder gently. WH ...

  • Lanier LW 210 - page 51

    WHEN D IS LIT OR BLINKING The "Add Toner" indicator blinks when toner is running short, and is continuously lit when toner has run out. Replace the toner cartridge (toner container). ✏ Do not reuse once-used toner because it affects the copy quality. ✏ You can make some copies even if the "Add Toner" indicator blinks. Howeve ...

  • Lanier LW 210 - page 52

    3 Rotate the toner cartridge down- ward and press it to the right to remove it from the copier. ✏ Dispose of the used toner container according to local regulations. 4 Shake the new toner cartridge lightly five to ten times to remove lumps. 5 Insert the toner cartridge from its left end. 6 Remove the green seal only. WHEN D IS LIT OR BLINKING 44 ...

  • Lanier LW 210 - page 53

    7 Rotate the toner cartridge by pulling up the tab on its right end as shown in the figure on the right. 8 Close the toner cartridge cover. 9 Close the original table and manual feed table. ✏ It takes about a minute to add the toner. A sound might be heard from inside the copier. WHEN D IS LIT OR BLINKING WHAT TO DO IF SOMETHING GOES WRONG 45 ...

  • Lanier LW 210 - page 54

    ...

  • Lanier LW 210 - page 55

    MAINTAINING YOUR COPIER FUNCTIONS THAT CAN BE RESET . . . . . . . . . . . . . . . . . . . 48 COPY MAGNIFICATION/CUT LENGTH ADJUSTMENT . . . . 49 DO’S AND DON’TS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 DAILY MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 PAPER/TONER . . . . . . . . . . . . . . ...

  • Lanier LW 210 - page 56

    FUNCTIONS THAT CAN BE RESET You can make the copier easier to use by resetting some functions to meet your copying needs. When you want to reset a function, contact your service representative. You can reset the following functions: Changing the Auto Reset time The copier resets itself to the initial settings if it is idle for about 2 minutes durin ...

  • Lanier LW 210 - page 57

    COPY MAGNIFICATION/CUT LENGTH ADJUSTMENT This function adjusts the copy magnification and paper cut length in the paper feed direction. The copy magnification can be adjusted from -1 to 1 % in 0.05 % steps and the paper cut length from -10 to 10 mm, -0.5 to 0.5" in 1 mm, 0.1" steps. 1 Press the Enter key until "A.1" appears on t ...

  • Lanier LW 210 - page 58

    4 Use the and keys to enter a value to be set. When you press the Clear/Stop key, "0" is entered for the value to be set. 5 Press the Enter key. The Trailing Edge indicator blinks. The paper cut length indicator lights. 6 Repeat 2 to 5 for all the settings. 7 Press the Enter key until "A.1" disappears from the Trailing Edge indi ...

  • Lanier LW 210 - page 59

    DO’S AND DON’TS S Since some parts of the copier are supplied with high electrical voltage, touch only the parts specified in this manual. S While copying, do not turn off the main switch. When you turn off the copier, confirm that all copy runs have finished. S Do not step on or trip on the power cord. S Do not unplug the power cord even after ...

  • Lanier LW 210 - page 60

    S To avoid possible build-up ozone, make sure to locate this copier in a large well-ventilated room that has an air turnover of more than 30 m 3 /hr/person. S When the main switch is in the Stand-by position, the anticondensation heaters are on. In case of emergency, unplug the machine’s power cord. Then contact your service representative. DO’ ...

  • Lanier LW 210 - page 61

    DAILY MAINTENANCE If the exposure glass is dirty, you cannot make copies as you want. Clean it if you find it dirty. S When you clean the exposure glass, use the following clothes: • Well-wrung damp cloth • Dry cloth S For cleaning internal parts other than the exposure glass, contact your service representative. ✏ Do not use any chemical cle ...

  • Lanier LW 210 - page 62

    PAPER/TONER Notes on Paper S Do not set the following paper. Otherwise, a paper jam might occur. • Bent, folded, or creased paper • Torn paper • Perforated paper • Non-smooth paper • Slippery paper • Thin paper that has low stiffness S Do not make a copy on paper with any kind of coating, such as thermosen - sitive paper, art paper, alu ...

  • Lanier LW 210 - page 63

    WHERE TO PUT YOUR COPIER This section shows the precautions you should follow when you move the copier if your office changes the equipment layout or moves to another location. S When you move the copier, contact your service representative. Installation Conditions S Install the copier in a location with the following range of temperature and humid ...

  • Lanier LW 210 - page 64

    S When you install the copier near another electronic equipment, they might affect each other. In particular, when the copier is placed near a television or radio, their programs might be hampered by noises. In such a case, take the following actions: • Leave enough space between the copier and the television or radio. • Reorient the television ...

  • Lanier LW 210 - page 65

    Power Connection R WARNING: Only connect the copier to the power source described on the inside front cover of this manual. Avoid multi-wiring as it could cause an electric shock or a fire. Avoid using an extension cord. Make sure the wall outlet is near the copier and freely accessible so outlet is near the copier and freely accessible so that in ...

  • Lanier LW 210 - page 66

    ...

  • Lanier LW 210 - page 67

    SPECIFICATIONS SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 OTHER OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 ...

  • Lanier LW 210 - page 68

    SPECIFICATIONS Spirio 700W Configuration Console Scanning Original moving over a fixed fiber optics array Photosensitivity Type OPC drum Copy Process Dry electrostatic transfer system Development Dry two-component magnetic brush system Fusing Heating roll system (oilless) Originals Sheet Original Size Maximum: 914(W) × 3,600(L) mm, 36" × 142 ...

  • Lanier LW 210 - page 69

    Power Source See inside this manual’s front cover. Power Consumption Maximum 1.41 kW Copy cycle condition 1.36 kW Warm up condition 1.21 kW Stand by condition 0.1 ~ 1.2 kW Noise emission: Sound pressure level (The measurements are made according to ISO 7779 at the operator position.) Roll feed copying: Less than 76 dB (A) Noise emission: Sound po ...

  • Lanier LW 210 - page 70

    OTHER OPTIONS This copier has the following options in addition to those shown in this manual. For more information, contact your local dealer. Product name Use Paper Spool When you use several types of roll paper, you can replace the roll paper quickly by setting one paper roll on the paper spool in advance. Manual table guide Use the guide to kee ...

  • Lanier LW 210 - page 71

    ...

  • Lanier LW 210 - page 72

    Custom er Visio n® _ our commitmen t to your complete s atisfact ion Lanier Worldwid e, Inc. | 2300 Parklake Drive, N.E. | Atlanta, GA USA 30345 www .lanier .com your doc ument management p artner ...

Manufacturer Lanier Category Copier

Documents that we receive from a manufacturer of a Lanier LW 210 can be divided into several groups. They are, among others:
- Lanier technical drawings
- LW 210 manuals
- Lanier product data sheets
- information booklets
- or energy labels Lanier LW 210
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lanier LW 210.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lanier LW 210, service manual, brief instructions and user manuals Lanier LW 210. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lanier LW 210.

Similar manuals

A complete manual for the device Lanier LW 210, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lanier LW 210 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lanier LW 210.

A complete Lanier manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lanier LW 210 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lanier LW 210, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lanier LW 210, that we can find in the current document
3. Tips how to use the basic functions of the device Lanier LW 210 - which should help us in our first steps of using Lanier LW 210
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lanier LW 210
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lanier LW 210 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lanier LW 210?

Use the form below

If you did not solve your problem by using a manual Lanier LW 210, ask a question using the form below. If a user had a similar problem with Lanier LW 210 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)