English dropdown-ico

Manual Delta 34-814

28 pages 1.78 mb
Download

Go to site of 28

Summary
  • Delta 34-814 - page 1

    INSTRUCTION MANUAL P ART NO. 422-04-651-0064 - 06-20-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). UNISA W ® 10" Right Tilting Arbor Saw (Models 34-801, ...

  • Delta 34-814 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 34-814 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 34-814 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 34-814 - page 5

    5 ADDITIONAL SPECIFIC SAFETY RULES 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. 4. USE ...

  • Delta 34-814 - page 6

    6 GROUNDING INSTRUCTIONS THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERA TOR FROM ELECTRIC SHOCK. Permanently connected machines: If the machine is intended to be permanently connected, all wiring must be done by a qualified electrician and conform to the National Electric Code and all local codes and ordinances. * THREE PHASE OPERA ...

  • Delta 34-814 - page 7

    7 3. DUST CHUTE ADAPTER 4. HANDWHEEL 5. BLADE GUARD AND SPLITTER BRACKET 6. MITER GAUGE 7. EXTENSION WING 8. HANGERS FOR RIP FENCE (2) 9. CLOSED-END ARBOR WRENCH 10. OPEN-END ARBOR WRENCH 11. UPPER BRACKET FOR SPLITTER 11A. LOWER BRACKET FOR SUPPOR T ROD 12. SUPPORT ROD 13. LOCKNOB 14. MOTOR COVER 15. 1/8" AND 5/64" HEX WRENCHES 16. 5/16- ...

  • Delta 34-814 - page 8

    8 1. Install the fiber washer (A) Fig. 3 on the shaft (B). Install the key (C) into the shaft keyway . 2. Place the handwheel (D) on the shaft (B) Fig. 3. Align the gr oove (E) in the handwheel with the key (C). 3. Push the handwheel snugly against the fiber washer and tighten the set scr ew . 4. Thr ead the lockknob (F) Fig. 4 into the shaft (B). ...

  • Delta 34-814 - page 9

    9 Use a straight edge (C) Fig. 6 to be sure that the extension wing (A) and the saw table (D) are even with each other before tightening the scr ews (B) Fig. 5. C A D If your saw has magnetic push button electrical controls, the starter box is already wir ed to the switch and motor . However , you will need to mount the starter box to the saw cabin ...

  • Delta 34-814 - page 10

    10 1. The Magnetic Starter on/of f switch (A) Fig. 9 comes attached to a mounting bracket on the right side of the machine. Remove it. 2. Insert a 5/16-18x1" flat head scr ew (D) with a 5/16" flat washer (E) through the hole (G) in the fr ont lip of the extension table and through the switch bracket (A). Use a 5/16-18 hex nut to loosely a ...

  • Delta 34-814 - page 11

    11 3. T o check the alignment, remove the screw and fastener plate (C) Fig. 13. Use a straight edge (D) Fig. 14 to see if the splitter bracket (A) is aligned with the inside blade flange (B). Check both the top and bottom of bracket (A) with the top and bottom of flange (B). 4. T o adjust, loosen the two screws (F) Fig. 15, and adjust splitter brac ...

  • Delta 34-814 - page 12

    12 8. Use a 5/16-18x1" hex head bolt (N) with 5/16" lockwasher and 5/16" flat washer to attach the upper splitter bracket (M) Fig. 20 to the lower bracket (L) . NOTE: Hand tighten only . 9. Insert the fr ont end of splitter (P) Fig. 21, inside the splitter mounting bracket, behind the splitter fastener plate and the screw (C). Push t ...

  • Delta 34-814 - page 13

    13 12. Use a straight edge (A) Fig. 25 to make certain that the splitter (P) is aligned with the saw blade (B). Use a square (C) Figs. 27 and 28 to make certain that the saw blade (B) Fig. 26 and splitter (P) Fig. 27 are 90° to the table surface. Tighten all splitter mounting hardwar e (D) Fig. 27 and re-check the alignment. 13. Hold the clear bla ...

  • Delta 34-814 - page 14

    14 Use four #10 x 1/2" sheet metal screws to attach the rip fence holder brackets (A) and (B) Fig. 33 to the four holes located in the left hand side of the saw cabinet. The Unisaw is supplied with a dust chute adapter to connect a 4" diameter dust collector hose to the machine. Align the four holes in the adapter (A) Fig. 34 with the fou ...

  • Delta 34-814 - page 15

    15 Raise or lower the saw blade with the front handwheel (A) Fig. 41. With the exception of hollow ground blades, raise the blade 1/8" to 1/4" above the top surface of the workpiece. Raise hollow ground blades the maximum amount to provide gr eater clearance. T o raise the saw blade, loosen the lock knob (B) Fig. 37, and turn the handwhee ...

  • Delta 34-814 - page 16

    16 1. Raise the saw blade to its highest position. 2. Set the blade at 90° to the table by turning the blade tilting handwheel counterclockwise as far as it will go. 3. Use a combination square to see if the blade is at 90° to the table surface. 4. If the blade is not at 90° to the table, turn the blade tilting handwheel counter -clockwise. Loos ...

  • Delta 34-814 - page 17

    Insert the miter gauge bar into the miter gauge slot on the table. Attach the washer and lock handle (A) Fig. 43 to the miter gauge bar . The miter gauge is equipped with adjustable index stops at 90° and 45° right and left. Y ou can make adjustments to the index stops by tightening or loosening the three adjusting scr ews (B) Fig. 48 with the su ...

  • Delta 34-814 - page 18

    18 MACHINE USE COMMON SAWING OPERA TIONS Common sawing operations include ripping and crosscutting plus a few other standar d operations of a fundamental nature. As with all power machines, there is a certain amount of hazar d involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safet ...

  • Delta 34-814 - page 19

    19 RIPPING Ripping is cutting lengthwise through a boar d, (Fig. 49). NOTE : Be sur e the material to be cut is seasoned, dry and flat. The rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must hav ...

  • Delta 34-814 - page 20

    20 When ripping material with a veneer facing that extends over the material, the fence (A) should be in the horizontal position with the veneer (B) extending over the lip of the fence, as shown in Fig. 53 When ripping material with a veneer facing and the material is not thick enough for the veneer to extend over the lip of the fence or if the ven ...

  • Delta 34-814 - page 21

    21 USING MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various styles of corner moulds, picture frames, tabl ...

  • Delta 34-814 - page 22

    1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 61). V arious combinations of saws and cutters are used to cut grooves fr om 1/8 ″ to 13/16 ″ for use in shelving, making joints, tenoning, grooving, etc. The cutters ar e heavily swaged and mus ...

  • Delta 34-814 - page 23

    23 USING AUXILIAR Y WOOD F ACING ON RIP FENCE When performing special cutting operations – and that operation may cause the cutting implement to contact the fence – it is necessary to add a wood facing (A) Fig. 145, to one side of the rip fence as shown. The wood facing is attached to the fence with wood screws through holes drilled in the fenc ...

  • Delta 34-814 - page 24

    24 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the fe ...

  • Delta 34-814 - page 25

    25 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE NOTE: T wo wrenches are supplied with the saw for changing the saw blade: a box-end wrench and open- end wrench. 1. Re ...

  • Delta 34-814 - page 26

    26 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta 34-814 - page 27

    27 T wo Y ear Limited New Product W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized serv ...

  • Delta 34-814 - page 28

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer Delta Category Saw

Documents that we receive from a manufacturer of a Delta 34-814 can be divided into several groups. They are, among others:
- Delta technical drawings
- 34-814 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 34-814
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 34-814.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 34-814, service manual, brief instructions and user manuals Delta 34-814. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 34-814.

Similar manuals

A complete manual for the device Delta 34-814, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 34-814 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 34-814.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 34-814 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 34-814, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 34-814, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 34-814 - which should help us in our first steps of using Delta 34-814
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 34-814
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 34-814 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 34-814?

Use the form below

If you did not solve your problem by using a manual Delta 34-814, ask a question using the form below. If a user had a similar problem with Delta 34-814 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)