Manual Hudson Sales & Engineering 5000 Series

8 pages 2.31 mb
Download

Go to site of 8

Summary
  • Hudson Sales & Engineering 5000 Series - page 1

    Installation Manual 5000 Page 1 of 8 August 2000 T uf-Lite  and T uf-Lite II  Fans 5000 Series Hub INST ALLA TION MANUAL Adjustable Pitch Fan Assembly 22’ through 30’ Diameter Hudson T uf-Lite ® and T uf-Lite II ® fan blades Hudson T uf-Lite ® (black) fan blades are made from fiberglass reinforced epoxy resin having a very high strengt ...

  • Hudson Sales & Engineering 5000 Series - page 2

    Installation Manual 5000 Page 2 of 8 August 2000 ASSEMBL Y WITH BUSHING Clean all mating surfaces between hub, bushing and shaft. All grease and lubricant should be removed, leaving the mating sur - faces dry . If there is no shoulder on shaft to prevent bushing from sliding down shaft, slide spacer/sleeve (not provided) on shaft before bush- ing o ...

  • Hudson Sales & Engineering 5000 Series - page 3

    Installation Manual 5000 Page 3 of 8 August 2000 THRUST RET AINER (optional equipment) Install proper load bolt (not provided) into top of fan shaft and tighten (See Figure 1). Install thrust retainer channel on top hub plate using existing hub spool cap screws. T orque cap screws to 60-65 ft-lb. Install thrust retainer eyebolt and jam nut. Hand ti ...

  • Hudson Sales & Engineering 5000 Series - page 4

    Installation Manual 5000 Page 4 of 8 August 2000 Rotate blade in clamp until digital protractor shows specified pitch angle to within ± 0.2˚. Fan pitch angle is shown on fan specification sheet for design duty . After desired pitch angle is set, raise and lower end of fan blade and find midpoint of blade travel. Hold blade at the midpoint. Pull b ...

  • Hudson Sales & Engineering 5000 Series - page 5

    Installation Manual 5000 Page 5 of 8 August 2000 After mounting, install flat washer, lock washer , and 3/8” NC nuts. Tighten to 15 ft-lb (lubricated) or 20 ft-lb (dry). (See Figure 7) Note: Refer to instructions included with seal disc for further details. Figure 7 CHECKING TIP CLEARANCE Rotate fan in position inside fan stack to check tip clear ...

  • Hudson Sales & Engineering 5000 Series - page 6

    Installation Manual 5000 Page 6 of 8 August 2000 HUDSON PRODUCTS CORPORA TION Adjustable Pitch Fan Assembly 22’ Thru 30’ Diameter Series 5000 HUB ST ANDARD MA TERIALS & FINISHES Blades: Fiberglass reinforced vinyl ester or epoxy Blade Clamps: Epoxy Coated Aluminum (Std) Hub Spool: Ductile Iron, Zinc Rich Coating Ductile Iron (Optional) Plat ...

  • Hudson Sales & Engineering 5000 Series - page 7

    Installation Manual 5000 Page 7 of 8 August 2000 HU B MODEL N O. & SERIAL N O. 1 5 68 7 10 9 F U R N IS HED WI TH BUS HIN G KEY , SET SC REW & CAP SCR EWS 3 2 BALANC E. (BL U E BLADES O NL Y) AND F I NAL M OM ENT D ATE O F M ANU FAC T UR E SERIAL N O. BLADE MODEL N O. 4 2 8 7 10 2 7 8 4 9 3 5 6 1 ...

  • Hudson Sales & Engineering 5000 Series - page 8

    Installation Manual 5000 Page 8 of 8 August 2000 1307 Soldiers Field Drive Sugar Land, T exas 77479-4072 Post Of fice Box 20029 Sugar Land, T exas 7777496-0029 Phone: (281) 275-8100 Fax: (281) 275-8388 1-800-634-9160 (24 Hours) EMAIL: hudson.products@hudsonproducts.com http://www .hudsonproducts.com Hudson, Auto-V ariable, Combin-Air e, Exact-A-Pit ...

Manufacturer Hudson Sales & Engineering Category Fan

Documents that we receive from a manufacturer of a Hudson Sales & Engineering 5000 Series can be divided into several groups. They are, among others:
- Hudson Sales & Engineering technical drawings
- 5000 Series manuals
- Hudson Sales & Engineering product data sheets
- information booklets
- or energy labels Hudson Sales & Engineering 5000 Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hudson Sales & Engineering 5000 Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hudson Sales & Engineering 5000 Series, service manual, brief instructions and user manuals Hudson Sales & Engineering 5000 Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hudson Sales & Engineering 5000 Series.

A complete manual for the device Hudson Sales & Engineering 5000 Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hudson Sales & Engineering 5000 Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hudson Sales & Engineering 5000 Series.

A complete Hudson Sales & Engineering manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hudson Sales & Engineering 5000 Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hudson Sales & Engineering 5000 Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hudson Sales & Engineering 5000 Series, that we can find in the current document
3. Tips how to use the basic functions of the device Hudson Sales & Engineering 5000 Series - which should help us in our first steps of using Hudson Sales & Engineering 5000 Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hudson Sales & Engineering 5000 Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hudson Sales & Engineering 5000 Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hudson Sales & Engineering 5000 Series?

Use the form below

If you did not solve your problem by using a manual Hudson Sales & Engineering 5000 Series, ask a question using the form below. If a user had a similar problem with Hudson Sales & Engineering 5000 Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)