English dropdown-ico

Manual Vermont Casting DBT39

34 pages 5.41 mb
Download

Go to site of 34

Summary
  • Vermont Casting DBT39 - page 1

    INST ALLER: DO NOT DISCARD THIS MANUAL - LEA VE FOR HOMEOWNER 10002789 08/00 Rev . 0 I NST ALLA TION I NSTRUCTIONS & H OMEOWNER ' S M ANUAL DO NOT ST ORE OR USE GASOLINE OR OTHER FLAMMABLE V APOURS AND/OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. FOR YOUR SAFETY WHA T T O DO IF YOU SMELL GAS: * Do not try to light any applian ...

  • Vermont Casting DBT39 - page 2

    DBT33/DBT36/DBT39 -2- 10002789/0 T ABLE O F C ONTENTS Please Read The Installation & Operating Instructions Car efully Befor e Using The Appliance. Important: Read all the instructions and warnings carefully befor e starting the installation. Failur e to follow these instructions fully may result in a possible r e hazard and will void the ma ...

  • Vermont Casting DBT39 - page 3

    10002789/0 -3- DBT33/DBT36/DBT39 This gas replace should be installed by a qualied installer in accordance with local building codes and with current CAN /CGA-B149 (. 1 or .2) Installation codes for Gas Burning Fireplaces and Equipment. FOR U.S.A Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1. FOR SAFE ...

  • Vermont Casting DBT39 - page 4

    DBT33/DBT36/DBT39 -4- 10002789/0 A PPLIANCE D IMENSIONS Appliance Dimensions Ref. DBT33 DBT36 DBT39 A 838 mm (33") 914 mm (36") 991 mm (39") B 733 mm (28.87") 870 mm (34.25") 870 mm (34.25") C 416 mm (16.37") 533 mm (21") 533 mm (21") D 787 mm (31") 838 mm (33") 914 mm (36") E 559 mm (22&q ...

  • Vermont Casting DBT39 - page 5

    10002789/0 -5- DBT33/DBT36/DBT39 C LEARANCE TO C OMBUSTIBLES Appliance T op ............................. 0 mm (0") Bottom ....................... 0 mm (0") Side ............................ 0 mm (0") Back ........................... 0 mm (0") V enting Concentric sections of DV V ent T op, bottom & sides .. 25 mm (1") M ...

  • Vermont Casting DBT39 - page 6

    DBT33/DBT36/DBT39 -6- 10002789/0 F INAL F INISHING Non-combustible materials such as brick or tile may be extended over the edges of the face of the appliance. DO NOT cover any vent or grille panels. If a T rim Kit is going to be installed on the replace, the brick or tile will have to be installed ush with the edges of the appliance. G AS S ...

  • Vermont Casting DBT39 - page 7

    10002789/0 -7- DBT33/DBT36/DBT39 G AS L INE I NST ALLA TION When purging the gas lines, the front glass must be removed. The gas pipeline can be brought in through the rear of the replace as well as the bottom. Knockouts are provided on the bottom behind the valve to allow for the gas pipe installation and testing of any gas connection. It is mo ...

  • Vermont Casting DBT39 - page 8

    DBT33/DBT36/DBT39 -8- 10002789/0 C ONVER TING T HE A PPLIANCE F ROM LP TO N A TU RAL G AS OR N A TURAL G AS T O LP . The DBT33 is convertible between Natural Gas an LP gas (and vice-versa) with the use of a conversion kit purchased seperately , see your dealer for the correct part number . The DBT36 & 39 can only be converted from Propane to Na ...

  • Vermont Casting DBT39 - page 9

    10002789/0 -9- DBT33/DBT36/DBT39 A = clearance above grade, veranda, por ch, deck, or bal- cony [* 12 inches (305mm) minimum] B = clearance to window or door that may be opened [12" (306mm)]. C = clearance to permanently closed window [minimum 12 inches (305mm) r ecommended to pr event condensation on window] D = vertical clearance to ventilat ...

  • Vermont Casting DBT39 - page 10

    DBT33/DBT36/DBT39 -10- 10002789/0 Fig. 1 1 Fig. 12 Fig. 13 Fig. 14 Fig. 15 ...

  • Vermont Casting DBT39 - page 11

    10002789/0 -1 1- DBT33/DBT36/DBT39 H OW T O U SE T HE V ENT G RAPH The vent chart should be read in conjunction with the follow- ing vent installation instructions to determin the relationship of the vertical and horizontal dimensions of the vent system 1. Determine the height of the centre of the horizontal vent pipe exiting through the outer wall ...

  • Vermont Casting DBT39 - page 12

    DBT33/DBT36/DBT39 -12- 10002789/0 V E R T ICA L S IDE W ALL A PP LIC A TIO NS Since it is very important that the venting system maintain its balance between the combustion air intake and the ue gas exhaust, certain limita- tions as to vent congurations apply and must be strictly adhered to. The V ent Graph showing the relationship between ve ...

  • Vermont Casting DBT39 - page 13

    10002789/0 -13- DBT33/DBT36/DBT39 V ER TICAL S IDEW ALL I NST ALLA TIONS STEP 1 Locate vent opening on the wall. It may be necessary to rst position the replace and measure to obtain hole location. Depending on whether the wall is combustible or non-combus- tible, cut opening to size. (Fig. 22) (For combustible walls rst frame in opening. ...

  • Vermont Casting DBT39 - page 14

    DBT33/DBT36/DBT39 -14- 10002789/0 STEP 6 Use appropriate length of pipe sections - telescopic or xed - and install the horizontal vent sections. The sections which go through the wall are packaged with the starter kit, and can be cut to suit if necessary . (Fig. 26). Sealing vent pipe and restop gaps with high temperature sealant will restric ...

  • Vermont Casting DBT39 - page 15

    10002789/0 -15- DBT33/DBT36/DBT39 DO NOT BACK FILL AROUND SNORKEL. A CLEARANCE OF A T LEAST 4” MUST BE MAINT AINED BETWEEN THE SNORKEL AND THE SOIL If the foundation is recessed, use recess brackets (not supplied) for securing lower portion of the snorkel. Fasten brackets to wall rst and then secure to snorkel with self-drilling #8 x 1/2 sheet ...

  • Vermont Casting DBT39 - page 16

    DBT33/DBT36/DBT39 -16- 10002789/0 • 7DVCS must be used to support offsets. (Fig. 36)This application will require that you rst determine the roof pitch and use the appropriate starter kit. (See V enting Components List) • The minimum height of the vent above the highest point of penetration through the roof is 2'. See Fig. 38. V ER TICA ...

  • Vermont Casting DBT39 - page 17

    10002789/0 -17- DBT33/DBT36/DBT39 V ER TICAL T HROUGH -T HE -R OOF I NST ALLA TION 1. Locate your replace. 2. Plumb to centre of the (4") ue collar from ceiling above and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm). 4. Proceed to plumb for additional openings through the roof. In all cases, the open ...

  • Vermont Casting DBT39 - page 18

    DBT33/DBT36/DBT39 -18- 10002789/0 C RIMPED E ND V ENTING C OMPONENTS Starter Kit -Model 7DVSK - Sidewall V enting Starter Kit - Model 7TDVSKV - V ertical V enting for 7TDVSKV -A order 1/12 to 6/12 roof pitch for 7TDVSKV -B order 7/12 to 12/12 roof pitch for 7TDVSKV -F order at roof Starter Kit - Model 7DVSKS -Snorkel Kit for Below Grade Installa ...

  • Vermont Casting DBT39 - page 19

    10002789/0 -19- DBT33/DBT36/DBT39 T WIST L OCK V ENTING C OMPONENTS Starter Kit -Model 7TDVSK - Sidewall V enting Starter Kit - Model 7TDVSKV - V ertical V enting for 7TDVSKV -A order 1/12 to 6/12 roof pitch for 7TDVSKV -B order 7/12 to 12/12 roof pitch for 7TDVSKV -F order at roof Starter Kit - Model 7TDVSKS -Snorkel Kit for Below Grade Install ...

  • Vermont Casting DBT39 - page 20

    DBT33/DBT36/DBT39 -20- 10002789/0 G ENERAL O PERA TING I NSTRUCTIONS G LASS I NFORMA TION Only glass approved by CFM Majestic Inc. should be used on this replace. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. • Under no circumstances should this applia ...

  • Vermont Casting DBT39 - page 21

    10002789/0 -21- DBT33/DBT36/DBT39 I NST ALLA TION OF L OGS & L A V A R OCK Refer to the log identication chart to identify specic log numbers. 1. Remove the front glass / frame assembly . 2. Remove the logs from their packaging. The logs are fragile and should be handled with care. Keep the packaging material out of the reach of children ...

  • Vermont Casting DBT39 - page 22

    DBT33/DBT36/DBT39 -22- 10002789/0 F LAME & T EMPERA TURE A DJUSTMENT RN/RP & EN/EP Models For units equipped with ‘HI/LO’ valves the ame adjustment is accomplished by rotating the ‘HI/LO’ adjustment knob located near the centre of the gas control valve, Fig. 44 & 45 F LAME C HARACTERISTICS It is important to periodically perf ...

  • Vermont Casting DBT39 - page 23

    10002789/0 -23- DBT33/DBT36/DBT39 LIGHTING INSTRUCTIONS 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to "OFF". Do not force. 5. Close control access panel. 10. Push the control knob all the way in and hold. Immediately light the pilot by repeatedly depress- ing the piezo spark ignitor until a  ...

  • Vermont Casting DBT39 - page 24

    DBT33/DBT36/DBT39 -24- 10002789/0 TROUBLE SHOOTING THE GAS CONTROL SYSTEM HONEYWELL MILLIVOL T V AL VE ...

  • Vermont Casting DBT39 - page 25

    10002789/0 -25- DBT33/DBT36/DBT39 TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT NOV A 820 MILLIVOL T V AL VE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. W ARNING: BEFORE DOING ANY GAS CONTROL SER VICE WORK, REMOVE GLASS FRONT . SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spar ...

  • Vermont Casting DBT39 - page 26

    DBT33/DBT36/DBT39 -26- 10002789/0 R EPLACEMENT P AR TS L IST Items marked ‘*’ ar e not shown in the following parts pictorial page. Ref. Description DBT33 DBT36 DBT39 1 Log Set (complete) 10000470 10000023 10000024 1a Log - Front left BA2 BB6 BC5 1b Log - Front right BA3 BB7 BC6 1c Log - rear BA4 BB8 BC7 1d Log - T op left BA5 BB9 BC8 1e Log - ...

  • Vermont Casting DBT39 - page 27

    10002789/0 -27- DBT33/DBT36/DBT39 Ref. Description DBT33 DBT36 DBT39 * Knob, fan speed control, (FK24 option) 51882 51882 51882 17 Fan assembly , with bracket (FK12 option) ZA11 10 ZA11 10 ZA1 1 10 18 W indow frame assembly 10001803 10001425 54363 * W indow glass (with gasket) 10002822 10001781 10002821 * Gasket (window glass) 57317 57317 57317 19 ...

  • Vermont Casting DBT39 - page 28

    DBT33/DBT36/DBT39 -28- 10002789/0 P AR TS P ICT ORIAL ...

  • Vermont Casting DBT39 - page 29

    10002789/0 -29- DBT33/DBT36/DBT39 O PTIONAL A CCESSORIES A V AILABLE EB-1 E LECTRICAL B OX The EB-1 Electrical junction box when tted and correctly wired gives an easy and convenient power outlet for the optioal fan kit. If the EB-1 electrical junction box is being tted the replace must be electrically connected and grounded in accordance ...

  • Vermont Casting DBT39 - page 30

    DBT33/DBT36/DBT39 -30- 10002789/0 W IRING I NSTRUCTIONS The replace, when installed, must be electri- cally connected and grounded in accordance with local codes or , in the absence of local codes, with the current CSA C22.1 Canadian Electric Code. For U.S.A. installations follow the local codes and the national electrical code ANSI/NFP A No 70. ...

  • Vermont Casting DBT39 - page 31

    10002789/0 -31- DBT33/DBT36/DBT39 C ERAMIC R EFRACTOR Y K ITS Ceramic refractory panels are available in kit form for the DBT series appliances. Appliance Model Kit Name DBT33 33BDVTCR DBT36 36BDVCR DBT39 39BDVCR T ake care when handling the refractory panels as they are fragile until held in place and sup- ported. Installation, refer to Figs. 52 & ...

  • Vermont Casting DBT39 - page 32

    DBT33/DBT36/DBT39 -32- 10002789/0 D ECORA TIVE B A Y W INDOWS Bay window kits are available for the DBT33, DBT36 & DBT39 model appliances. When tting the Bay W indow Kits the original front frame/glass assembly MUST remain in place. The Bay W indow kit is tted over the existing front glass. Installation 1. Remove the upper and lower brass ...

  • Vermont Casting DBT39 - page 33

    10002789/0 -33- DBT33/DBT36/DBT39 ...

  • Vermont Casting DBT39 - page 34

    DBT33/DBT36/DBT39 -34- 10002789/0 410 Admiral Blvd. • Mississauga, Ontario , Canada L5T 2N6 • 905-670-7885 www .vermontcastings.com CFM Majestic, Inc. © Copyright CFM Majestic, Inc. BASIC W ARRANTY : The CFM Majestic, Inc.™ (hereinafter referred to collectively as the "Compan y") warrants that your new Vermont Castings Gas Applianc ...

Manufacturer Vermont Casting Category Indoor Fireplace

Documents that we receive from a manufacturer of a Vermont Casting DBT39 can be divided into several groups. They are, among others:
- Vermont Casting technical drawings
- DBT39 manuals
- Vermont Casting product data sheets
- information booklets
- or energy labels Vermont Casting DBT39
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Casting DBT39.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Casting DBT39, service manual, brief instructions and user manuals Vermont Casting DBT39. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Casting DBT39.

Similar manuals

A complete manual for the device Vermont Casting DBT39, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Casting DBT39 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Casting DBT39.

A complete Vermont Casting manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Casting DBT39 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Casting DBT39, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Casting DBT39, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Casting DBT39 - which should help us in our first steps of using Vermont Casting DBT39
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Casting DBT39
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Casting DBT39 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Casting DBT39?

Use the form below

If you did not solve your problem by using a manual Vermont Casting DBT39, ask a question using the form below. If a user had a similar problem with Vermont Casting DBT39 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)