Manual Denso PRO 60

28 pages 2.24 mb
Download

Go to site of 28

Summary
  • Denso PRO 60 - page 1

    T echnical Services Department DSCA P/N: LA990009-1219 Third Issue: Mar ch 2003 GAC P/N: LA484007-1441 Printed in the U.S.A. DENSO SALES CALIFORNIA, INC. 3900 Via Or o Avenue Long Beach CA 90810-1868 800-264-9573 / 310-834-6352 www .movincool.com OPERA TION MANUAL OFFICE PRO 60 READ THIS MANUAL CAREFULL Y FOR INSTRUCTIONS ON CORRECT INST ALLA TION ...

  • Denso PRO 60 - page 2

    LIMITED W ARRANTY DENSO SALES CALIFORNIA, INC. ("DENSO") warrants its MOVINCOOL Products only to the extent stated in its of ficial written warranties. Unless otherwise specifically provided in writing by DENSO, DENSO warrants to end- user that the Products shall be fr ee of defects in materials or workmanship and will function in accorda ...

  • Denso PRO 60 - page 3

    OPERA TION MANUAL OFFICE PRO 60 ...

  • Denso PRO 60 - page 4

    ii ...

  • Denso PRO 60 - page 5

    TABLE OF CONTENTS FOREWORD ............................................................................................ 1 Definition of T erms .......................................................................... 1 GENERAL WARNINGS & CAUTIONS .................................................... 2 INVENTOR Y ................................ ...

  • Denso PRO 60 - page 6

    iv ...

  • Denso PRO 60 - page 7

    FOREWORD Congratulations on purchasing the MovinCool portable air conditioner . This manual explains how to assemble, install and operate the MovinCool Office Pr o 60 portable air conditioning unit. Please r ead this operation manual thoroughly to familiarize yourself with the featur es of the unit and to ensure years of r eliable operation. Y ou m ...

  • Denso PRO 60 - page 8

    GENERAL W ARNINGS & CAUTIONS • All electrical work, if necessary , should only be performed by qualified electrical personnel. Repair to electrical components by non-certified technicians may result in personal injury and/or dam- age to the unit. All electrical components replaced must be genuine MovinCool parts, purchased fr om an authorized ...

  • Denso PRO 60 - page 9

    INVENTOR Y After unpacking your MovinCool unit, please check to make sur e you have the following items: •O f fice Pr o 60 MovinCool Unit (1) • Operation Manual/W arranty Card (1) NOTE: If any of these items were not included in the box or appear damaged, please contact your MovinCool reseller for replacement. OPERA TION MANUAL/ WARRANTY C ARD ...

  • Denso PRO 60 - page 10

    INST ALLA TION Choosing an Installation Site  CAUTION: Following are some pr ecautions to consider before choosing your installation site. Please review car efully as improper installation may r esult in personal injury or damage to the unit. • Do not use the unit in areas wher e leakage of flammable gas may occur . • Do not use the unit in ...

  • Denso PRO 60 - page 11

    INST ALLA TION (cont.) Moving the Unit Unlock the casters and push the MovinCool unit, using the side handles, to a flat, level surface and set the casters back to the LOCKED position. UNLOCKED LOCKED FRONT AND BACK HANDLES 5 ...

  • Denso PRO 60 - page 12

    INST ALLA TION (cont.) Plugging in the Unit • Check the pr ongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are pr esent, wipe off with a clean, dry cloth. • Check the power cord, plug and pr ongs for damage or excess play . If any damage or excess play is found, contact your MovinCool r eseller for r epair . • Fully ...

  • Denso PRO 60 - page 13

    FEA TURES OP60 Features • An electronic contr ol panel which allows the user to control the unit’ s operation easily . • Dual fan speeds (either High or Low) in both COOL and Fan Only modes. •A digital display that indicates the T emperatur e SET POINT (either Fahrenheit or Celsius) in which the COOL Mode will operate. This is also the temp ...

  • Denso PRO 60 - page 14

    TANK FULL SET POINT F C ROOM TEMP AM PM SET TEMP CLOCK/TIMER FAN ON/OFF COOL ON/OFF PROGRAM Office Pro 60 SET ST ART TIME END TIME SET CLOCK RUN HRS MIN 6 5 4 3 2 1 OPERA TION Control Panel Befor e operating the unit, it is important to familiarize yourself with the basic controls located on the contr ol panel. ➀ COOL ON/OFF Activates/deactivates ...

  • Denso PRO 60 - page 15

    OPERA TION (cont.) Control Panel (Cont.) ➆ T emperature Scale Illuminates to indicate the curr ent LED temperatur es being displayed are either in °C or °F; also used to display the clock when programming. ➇ AM/PM LED Illuminates to indicate AM or PM time of day . ➈ Program RUN Activates/deactivates a program. Button ➉ Program SET Allows ...

  • Denso PRO 60 - page 16

    OPERA TION (cont.) Operating in COOL Mode ➀ The unit can be operated in COOL mode by pr essing the COOL ON/OFF button (LED illuminates). NOTE: In COOL mode the unit can only be turned off by pressing the “COOL ON/OFF” button again, not by pressing the fan buttons. ➁ Change the fan speed by pr essing the HIGH or LOW fan buttons. ➂ Change t ...

  • Denso PRO 60 - page 17

    OPERA TION (cont.) How to Set a Program ➀ Setting a ST ART TIME Press the Pr ogram SET button. The Program SET button and ST AR T TIME LEDs will illuminate. Pr ess the HRS and MIN buttons to set the ST ART TIME. ➁ Setting an END TIME Press the Pr ogram SET button until the END TIME LED illuminates. Press the HRS and MIN buttons to set the END T ...

  • Denso PRO 60 - page 18

    OPERA TION (cont.) How to Set a Program (Cont.) NOTE: • The unit will return to the previous mode if a program is turned off while it is running. • The Program RUN LED flashes while a program is running. It is illuminated continuously when the program mode is activated. • While a program is running, the program can only be stopped by pressing ...

  • Denso PRO 60 - page 19

    OPERA TION (cont.) Operating Modes Office Pr o 60 operates in 2 modes, F AN Only and COOL. When in F AN Only mode, the unit circulates the surr ounding air . When in COOL mode, the compressor is operational and cool air is cir culated. • COOL Mode Office Pr o 60 will operate in F AN Only mode for appr oximately 120 seconds before the compr essor ...

  • Denso PRO 60 - page 20

    OPERA TION (cont.) Emptying the Drain T ank (If equipped) During COOL mode, condensate will accumulate in the drain tank. When the drain tank becomes full, the FULL T ANK LED will flash and the unit will shut off automatically . NOTE: If you want to empty the drain tank, while the unit is in operation, press the COOL ON/OFF button to turn the unit ...

  • Denso PRO 60 - page 21

    A B OPERA TION (cont.) Drain Pump A drain pump is included to allow continuous operation and to eliminate the need for a drain tank. • When the water collects to level (A) in the pump reservoir , the drain pump begins to operate and dischar ges the water . • When the water level drops below level (B), the drain pump will stop. NOTE: • If for ...

  • Denso PRO 60 - page 22

    HOSE INST ALLA TION Note: The OP60 is equipped with a 20 foot (6 m) hose. Connect the 20 foot (6 m) hose to the drain outlet spout and feed it through the gr ommet on the right hand side of the unit. Note: Do not use more than 18 feet (5.5 m) of drain hose vertically . This is the maximum head (lift) of the Condensate Pump. When securing the drain ...

  • Denso PRO 60 - page 23

    DAIL Y INSPECTION & MAINTENANCE Emptying the Drain T ank To empty the drain tank, r efer to instructions, page 14. Cleaning the Air Filters Clean the air filters once a week. If the unit is used in a dusty envir on- ment, more fr equent cleaning may be requir ed. A dirty air filter r educes air output resulting in a decr ease of the cooling cap ...

  • Denso PRO 60 - page 24

    DAIL Y INSPECTION & MAINTENANCE (cont.) Cleaning Method ➀ Remove dust from the element with a vacuum cleaner , or rinse in cold or lukewarm water . If the element is extremely dirty , wash with a neutral deter gent. ➁ After the element has been cleaned, rinse with clean running water , allow to dry , then r einstall. In-Season/Off-Season In ...

  • Denso PRO 60 - page 25

    TROUBLESHOOTING Office Pr o 60 Self-Diagnostic Codes Self-Diagnostic Codes will be displayed on the Contr ol Board under the following conditions: TANK FULL SET POINT F C ROOM TEMP AM PM SET TEMP CLOCK/TIMER FAN ON/OFF COOL ON/OFF PROGRAM Office Pro 60 SET ST ART TIME END TIME SET CLOCK RUN HRS MIN Check the following points before calling a qualif ...

  • Denso PRO 60 - page 26

    TECHNICAL SPECIFICA TIONS ITEM/FEA TURES OFFICE PRO 60 Rating Conditions dry bulb 95º F (35º C) wet bulb 83º F (28.2º C) humidity 60% Specifications power frequency 60Hz line voltage single phase 208/230V power consumption 7.1 Kw current consumption 33 Amps power factor 99% starting current 140A power wiring 6 (3-core) A WG Cooling Unit cooling ...

  • Denso PRO 60 - page 27

    LIMITED W ARRANTY DENSO SALES CALIFORNIA, INC. ("DENSO") warrants its MOVINCOOL Products only to the extent stated in its of ficial written warranties. Unless otherwise specifically provided in writing by DENSO, DENSO warrants to end- user that the Products shall be fr ee of defects in materials or workmanship and will function in accorda ...

  • Denso PRO 60 - page 28

    T echnical Services Department DSCA P/N: LA990009-1219 Third Issue: Mar ch 2003 GAC P/N: LA484007-1441 Printed in the U.S.A. DENSO SALES CALIFORNIA, INC. 3900 Via Or o Avenue Long Beach CA 90810-1868 800-264-9573 / 310-834-6352 www .movincool.com OPERA TION MANUAL OFFICE PRO 60 READ THIS MANUAL CAREFULL Y FOR INSTRUCTIONS ON CORRECT INST ALLA TION ...

Manufacturer Denso Category Air Conditioner

Documents that we receive from a manufacturer of a Denso PRO 60 can be divided into several groups. They are, among others:
- Denso technical drawings
- PRO 60 manuals
- Denso product data sheets
- information booklets
- or energy labels Denso PRO 60
All of them are important, but the most important information from the point of view of use of the device are in the user manual Denso PRO 60.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Denso PRO 60, service manual, brief instructions and user manuals Denso PRO 60. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Denso PRO 60.

Similar manuals

A complete manual for the device Denso PRO 60, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Denso PRO 60 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Denso PRO 60.

A complete Denso manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Denso PRO 60 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Denso PRO 60, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Denso PRO 60, that we can find in the current document
3. Tips how to use the basic functions of the device Denso PRO 60 - which should help us in our first steps of using Denso PRO 60
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Denso PRO 60
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Denso PRO 60 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Denso PRO 60?

Use the form below

If you did not solve your problem by using a manual Denso PRO 60, ask a question using the form below. If a user had a similar problem with Denso PRO 60 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)