English dropdown-ico

Manual Fujitsu PCI GigabitEthernet 3.0

115 pages 3.7 mb
Download

Go to site of 115

Summary
  • Fujitsu PCI GigabitEthernet 3.0 - page 1

    FUJITSU PCI GigabitEthernet 3.0 Update1 for Solaris TM Operating System User's Guide ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 2

    For Safe Operation Handling of This Manual This manual contains important information regardi ng the use and handling of this product. Read this manual thoroughly . Pay special attention to the sect ion "Important W arnings". U se the product according to the instruction s and information ava ilable in this manual. FUJITSU makes ev ery ef ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 3

    Revision History Edition Date Revised section (*1) (Added/Deleted/Altered) Details 01 2003-2-20 - - Appendix D PRIMEPOWER1/100 is added 3.4 Change the procedure 3.3.1 Some parameter e xplanations are added 02 2003-5-1 3.5 Some procedures are added 3.6 VLAN information is added - Change the V ersion 2.0 to 2.1 03 2004-1-8 Appendix E VLAN tested swit ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 4

    Pr eface Purpose This manual describes how to install the FUJITSU PCI GigabitEthernet card in your PRIMEPOWER system, and configure the environm ent setting of the interface. T arget Reader This book is intended for system administrato rs responsible for installing the FUJITSU PCI GigabitEthernet card. T o understand the concepts and procedures pre ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 5

    iv ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 6

    Contents Chapter 1 Product Outline ....................................................................... 1 1.1 Key Features ................................................................................. 2 1.2 GigabitEthernet card Specifications .......................................................... 3 1.2.1 Specifications .................. ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 7

    Contents Appendix C Using GigabitEthernet in a Cluster Environment ....................................... 71 C.1 Cluster Environment Support ................................................................. 71 C.2 Cluster Environment Setup Procedure ......................................................... 71 C.3 Notes ............................ ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 8

    Chapter 1 Product Outline The following topics are described in this chapter. ● Key Features ● GigabitEthernet card Specifications ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 9

    Chapter 1 Product Outli ne 1.1 Key Features The FUJITSU GigabitEthernet card is a adapter designed for Solaris OS servers that are connected to a GigabitEthernet network. This card offers the physical services and data link services defined by IEEE802.3. Table 1.1 GigabitEthernet function Main Funct ion IEEE802.3 compliant 1000Base-SX(PW008GE4, PW0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 10

    1.2 Gigabi tEthernet car d Specifica tions 1.2 GigabitEthernet card Specifications The FUJITSU P CI GigabitEthernet card is an adapter that is installed into a PC I slot or a PCI Express slot. 1.2.1 Specifications The specification of the FUJITSU PCI GigabitEthernet adapter is listed in "Table 1.2.1 PCI GigabitEthernet Card Specification" ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 11

    Chapter 1 Product Outli ne connection is not supported. ● When using 1000Mbps transfer rate with PW008GE5, PW0G8GE2, PRIMEPOWER250/450 secondary LAN port, SE0X7GD1X, PW008QG1 and SE0X7GQ1X, only Auto-Negotiation=On can be used. 1.2.2 Part Names and Feat ures of Hardware Figure 1.1 to 1.8 shows the appearance of the FUJITSU PCI GigabitEthernet ada ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 12

    1.2 Gigabi tEthernet car d Specifica tions Figure 1.1 1000Base-SX (PW008GE4) Figure 1.2 10/100/1000B ase-T (PW008GE5) Figure 1.3 1000Base-SX (PW0G8GE1) Figure 1.4 10/100/1000B ase-T (PW0G8GE2) 5 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 13

    Chapter 1 Product Outli ne Figure 1.5 1000Base-SX * 2ports (SE0X7GD2X ) Figure 1.6 10/100/1000B ase-T * 2po rts (SE0X7GD1X ) 6 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 14

    1.2 Gigabi tEthernet car d Specifica tions Figure 1.7 10/100/1000B ase-T * 4po rts (PW0G8GE1) Figure 1.8 10/100/1000B ase-T * 4po rts (SE0X7GQ1X ) 7 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 15

    ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 16

    Chapter 2 Installing FUJITSU PCI GigabitEthernet Card This chapter describes the tasks necessary to install this card in the main unit. ● Installation of the GigabitEthernet card ● Identifying the GigabitEthernet card ● Cable connection ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 17

    Chapter 2 Installing FU JITSU PCI G igabitEthe rnet Card 2.1 Installation of the GigabitEthernet Card Insert the card in a PCI slot or a PCI Express slot on the main unit. (Please refer to the main unit ’ s User ’ s Manual for details about installing cards and specific PCI slot or PCI Express slot specifications.) 10 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 18

    2.2 Identi fying the Gig abitEtherne t Card 2.2 Identifying the GigabitEthernet Card The GigabitEthernet card can be identified by executing the "boot -r" command at the OpenBoot prompt. ok boot -r 11 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 19

    Chapter 2 Installing FU JITSU PCI G igabitEthe rnet Card 2.3 Cable Connection To connect the PW008GE4, PW0G8GE1 and SE0X7GD2X GigabitEthernet card to the network, use an optical fiber cable. To c onnect the PW008GE5, PW0G8GE2, PRIMEPOWR250/450 secondary LAN, PW008QG1, SE0X7GD1X and SE0x7GQ1X GigabitEthernet card to the network, use a CAT5E twisted ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 20

    2.3 Cable Connection Figure 2.3.2 PW008GE5 (with Twisted Pair Cat5E Cable) 13 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 21

    Chapter 2 Installing FU JITSU PCI G igabitEthe rnet Card Figure 2.3.3 PW0G8GE1 (with Optical Fiber Cable) 14 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 22

    2.3 Cable Connection Figure 2.3.4 PW0G8GE2 (with Twisted Pair Cat5E Cable) 15 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 23

    Chapter 2 Installing FU JITSU PCI G igabitEthe rnet Card Figure 2.3.5 SE0X7GD2X (with Optical Fiber Cable) 16 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 24

    2.3 Cable Connection Figure 2.3.6 SE0X7GD1X (with Twisted Pair Cat5E Cable) 17 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 25

    Chapter 2 Installing FU JITSU PCI G igabitEthe rnet Card Figure 2.3.7 PW008QG1 (with Twisted Pair Cat5E Cable) 18 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 26

    2.3 Cable Connection Figure 2.3.8 SE0X7GQ1X (with Twisted Pair Cat5E Cable) 19 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 27

    ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 28

    Chapter 3 Setting Configuration Information This chapter describes how to set configuration information after installing the FUJITSU PCI GigabitEthernet interface. The following topics are covered in this chapter: ● Driver Software Installation ● Environment Setting ● Operation Mode Setup ● Discernment of the GigabitEthernet interface ● N ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 29

    Chapter 3 Setting Confi guration In formation 3.1 Driver Software Installation To make use of the FUJITSU PCI GigabitEthernet interface, Solaris OS version-specific driver packages must be installed from the attached CD-ROM. See the document " Installation Guide FUJITSU PCI GigabitEthernet 3.0 Update1 " for the installation procedure. 22 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 30

    3.2 Enviro nment Setting 3.2 Environment Setting This section explains how to edit the necessary file to configure the operating environment of the FUJITSU PCI GigabitEthernet interface. In TCP/IP (IPv4 or IPv6) protocol, edit the following information must be setup. ● Configuring the Hostname file ● Hostname Definition ● Netmask Value Defini ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 31

    Chapter 3 Setting Confi guration In formation Example /etc/hosts file: # IP Address Hostname 190.168.150.1 giga-v4 24 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 32

    3.2 Enviro nment Setting 2. To use the GigabitEthernet interface as an IPv6 interface: Add the IPv6 address and hostname to the /etc/inet/ipnodes file. Example /etc/inet/ipnodes file: # IP Address Hostname fe80::2e0:ff:fea6:2222 giga-v6 3.2.3 Netmask Value Definition To use the GigabitEthernet interface as an IPv4 interface, add the netmask value a ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 33

    Chapter 3 Setting Confi guration In formation 3.3 Operation Mode Setup This section explains how to edit the fjgi.conf configuration file or issue a command to change the operation mode of the FUJITSU PCI GigabitEthernet interface. The operation mode can be changed with the following: ● The fjgi.conf file ● JumboFrame Setup ● The ndd Utility ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 34

    3.3 Operat ion Mode Setu p Parameter Val ue Descriptio n Off Auto-Negotiation is disabled. (Fixed mode) Auto (default) Connection speed of 1000, 100, or 10 Mbps is set based on negotiation with the remote device. (This can only be set when AutoNegotiation_A=On.) 1000 Connect at 1000Mbps. 100 Connect at 100Mbps. LinkSpeed_A *2 10 Connect at 10Mbps. ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 35

    Chapter 3 Setting Confi guration In formation file. example) # grep fjgi /etc/path_to_inst "/pci@83,2000/FJSV,pwga@1" 0 "fjgi" - PRIMEPOWER250/450 secondary LAN port "/pci@15,2000/FJSV,pgtb@1" 1 "fjgi" - PW008GE5, PW0G8GE2 "/pci@17,2000/FJSV,pgsb@1" 2 "fjgi" - PW008GE4, PW0G8GE1 "/pci ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 36

    3.3 Operat ion Mode Setu p ― The example which sets a parameter to a fjgi.conf file is shown. example 1. the case where use the card of PW008GE5 (10/100-/1000BASE-T), and disable Auto-Negotiation and connection speed is made into 100Mbps and Half-Duplex name="fjgi" parent="/pci@15,2000" unit-address="1" AutoNegotiati ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 37

    Chapter 3 Setting Confi guration In formation 3.3.2 JumboFrame Setup By using a JumboFrame the TCP/IP MTU size can be expanded from 1500 to 9000. By expanding the single packet transmission size, the number of packets processed can be reduced, lowering the CPU load. There are three k inds of fo llowing meth ods in th e setting procedure of JumboF r ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 38

    3.3 Operat ion Mode Setu p 2. The MTU size o f TCP/IP is set up by creating / etc/fjmtu.fjgi* (notes) and describing MTU size in /etc/fjmtu.fjgi* in the form of th e follo wing between 1500 and 9000 and rebooting. When not specif ying an MTU value as this file, it is set as a default value (except for a 9000Byte MAC he ader) . (Note) * expr esses a ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 39

    Chapter 3 Setting Confi guration In formation ● The parameters set in /etc/fjmtu.fjgi* and fjgi.conf file are not effective with DR(Dynamic Reconfiguration) function and Pci Hot Plug function. To be effective this file, the system must be rebooted. 3.3.3 The ndd Utility By using the ndd command, the interface communication mode can be changed dyn ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 40

    3.3 Operat ion Mode Setu p ndd -set /dev/fjgi 'instance' value (Instance number "value" of an applicable interface is specified.) ndd -set /dev/fjgi 'param1' value (Change 1 of a setup) ndd -set /dev/fjgi 'param2' value (Change 2 of a setup) : : ndd -set /dev/fjgi 'adv_autoneg_cap' N (Once let Auto- ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 41

    Chapter 3 Setting Confi guration In formation parameter status meaning link_status Read only 0 : Link down 1 : Link up link_speed Read only 1000 : 1000Mbps 100 : 100Mbps 10 : 10Mbps link_mode Read only 0 : Half Duplex communication 1 : Full Duplex communication autonego Read only 0 : Auto-Negotiation is Off. 1 : Auto-Negotiation is On. flow_control ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 42

    3.3 Operat ion Mode Setu p parameter status meaning lp_10fdx_cap Read only The link-partner has been set to 10Mbps/FullDuplex by Auto-Negotiation. 0 : Invalid 1 : Valid lp_10hdx_cap Read only The link-partner has been set to 10Mbps/HalfDuplex by Auto-Negotiation. 0 : Invalid 1 : Valid lp_100fdx_cap Read only The link-partner has been set to 100Mbps ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 43

    Chapter 3 Setting Confi guration In formation is set up automatically. ● When you use ndd command and you change mode of operation, please let mode of operation in agreement with self-equipment and connection partner equipment. When mode of operation is not in agreement with self-equipment and con nection partner equipment, it may not become a va ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 44

    3.3 Operat ion Mode Setu p Auto-Negotiation off) from Auto-Negotiation mode. Setup to FCode is effective between OBP (Open Boot Prom). 1) The mode which can be set up on PW008GE4/PW0G8GE1/SE0X7GD2X (1000BASE-SX) is as follows. Execute the following command to set Full Duplex communication, 1000Mbps. example) ok transfer-speed=1000 2) The mode which ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 45

    Chapter 3 Setting Confi guration In formation The following example shows the current settings of a PW008GE5 card installed in a PRIMEPOWER600. {6} ok cd /pci@11,4000/FJSV,pgtb@5 {6} ok .properties duplex half <--*1 transfer-speed 0000000a <--*2 cabinet-name Cabinet#0 board-name Motherboard#1 assigned-addresses 83002810 00000000 00100000 0000 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 46

    3.4 Discer nment Of the GigabitEthe rnet Inter face 3.4 Discernment Of the Gigab itEthernet Interface This section explains how to distinguish the FUJITSU PCI GigabitEthernet interface instance number, interface type, and which slot the card is installed in. ● Discernment Of the GigabitEthernet Interface on PRIMEPOWER or GP7000 family ● Discern ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 47

    Chapter 3 Setting Confi guration In formation Logical bu s address Insta nce number Dri ver name "/pci@83,2000/FJSV,pwga@1" 0 fjgi "/pci@1f,0/pci@1/FJSV,pgsb@4" 1 fjgi "/pci@1f,0/pci@1/FJSV,pgtb@1" 2 fjgi "/pci@83,4000/pci@3/FJSV,p4ta@1" 3 fjgi "/pci@83,4000/pci@3/FJSV,p4ta@1,1" 4 fjgi "/pci@83 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 48

    3.4 Discer nment Of the GigabitEthe rnet Inter face # more /etc/path_to_inst | grep fjgi example) # more /etc/path_to_inst | grep fjgi "/pci@1,700000/pci@0/FJSV,e4ta@4" 0 "fjgi" "/pci@1,700000/pci@0/FJSV,e4ta@4,1" 1 "fjgi" "/pci@1,700000/pci@0,1/FJSV,e4ta@6" 2 "fjgi" "/pci@1,700000/pc ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 49

    Chapter 3 Setting Confi guration In formation 3.5 Network Installation This section explains how to perform a Solaris OS network installation using the FUJITSU PCI GigabitEthernet interface. 1. Please refer to the "Advanced Installation Guide" for information on the setup of the server and clients for Solaris Jumpstart. 2. On the installa ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 50

    3.5 Networ k Installatio n # cd /cdrom/cdrom0/FJSVgid_3.0/ <Solaris Level of client system> # ls FJSVgid* FJSVgid.us FJSVgidx.us FJSVgidr.us FJSVgidad.us # pkgadd -R mini_root_directory -d . # cd / NOTE: In this example, the i nstallation ser ver is setup to install Solaris 8 OS on the client. Substitute the appropriate Solari s level in the ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 51

    Chapter 3 Setting Confi guration In formation ok boot /pci@1f,4000/FJSV,pgtb@5 9. Install the Solaris OS. 10. After Solaris OS installation, check whether the FUJITSU PCI GigabitEthernet software has already been installed using the following command. # pkginfo | grep FJSVgid example) # pkginfo | grep FJSVgid system FJSVgid Fujitsu Gigabit Interfac ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 52

    3.6 VLAN I nterface Setu p 3.6 VLAN Interface Setup This section p rovides information about IEEE 802.1Q TagVLAN interfaces. This secti on also provides instructions for setting up VLAN interfaces using the FUJITSU PCI GigabitEt hernet interface. 3.6.1 IEEE 802.1Q TagVLAN Description The IEEE 802. 1Q TagVLAN fu nction allows the use of two or more ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 53

    Chapter 3 Setting Confi guration In formation and belonging to VID 231, the following is used: VLAN Interface Number = (1000 * VID) + Physical Instance Number fjgi231003 = (1000 * 231) + 3 Refer to "3.2 Environment Setting", and create the interface name fjgi231003 . Low 3 digits of VLAN interface number : physical instance number Upper d ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 54

    Chapter 4 LinkAggregation Feature This chapter outlines the LinkAggregation feature, and explains the settings required to use this feature. ● About the LinkAggregation feature ● Configuration of the LinkAggregation feature ● Notes ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 55

    Chapter 4 LinkAggregati on Feature 4.1 About LinkAggregation Feature This section explains the LinkAggregation feature. - LinkAggreg ation feature: The communication bandwidth and network reliability(*) can be improved by bundling two or more network interfaces as one logical interface (up to 8 physical interfaces can be bundled). It is effective w ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 56

    4.1 About LinkAggregati on Feature - Data Distr ibution Mode: Table 4.1.2 explains data distribution modes that FUJITSU PCI GigabitEthernet 3.0 supports. Table 4.1.2 Data Distribution Mode Destination MAC address distribution The LinkAggregation function determines the transmission path to be u sed from th e destination MAC address in the outgoing ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 57

    Chapter 4 LinkAggregati on Feature 4.2 Configuration of the Lin kAggregation Feature The LinkAggregation feature can be configured with one of the following methods: ● Setting Up the /etc/opt/FJSVla/config File ● Using the /etc/opt/FJSVla/bin/fjla Command ● PRIMECLUST ER GLS 4.1 A30 or later is required to use th e LinkAggregation feature. Th ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 58

    4.2 Config uration of th e LinkAggre gation Fea ture Member-instance: fjgi0, fjgi2 Distribution mode: Source/Destination IP address distribution The /etc/opt/FJSVla/config file for this configuration should look similar to the following: # # FJSVla: FUJITSU LinkAggregation setup sample file # # *attension: Don't use the different link_speed in ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 59

    Chapter 4 LinkAggregati on Feature ● The /etc/hostname.fjgiXX (XX: instance number) file is r equired for the aggregator-interface only (in the above example, /etc/hostname.fjgi1 is required). The LinkAggregation group defined in the configuration file is activated by rebooting the system. 4.2.2 Using the /etc/opt/FJSVla/bin/fjla Command The fjla ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 60

    4.2 Config uration of th e LinkAggre gation Fea ture # /etc/opt/FJSVla/bin/fjla init fjgi0 1:2 2 # fjgi0 FJ LinkAggregation now start. ● Before executing the command, the aggregator-interface must be already activat ed (the interface can be displayed by ifconfig -a), and the member instances must not be activated. ● The aggregator-interface mus ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 61

    Chapter 4 LinkAggregati on Feature - Descriptio n Inactivate the LinkAggregation group. - Exit code 0 : normal end. >0 : error end. - Example Inactivate the LinkAggregation group with aggregator-interface = fjgi0. # /etc/opt/FJSVla/bin/fjla term fjgi0 # FJ LinkAggregation stop. ● When aggregator-interface is inactivated (unplumb), it cannot pe ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 62

    4.2 Config uration of th e LinkAggre gation Fea ture - Display Fo rmat The following example shows that the status and statistics for a LinkAggregation group (aggregator-interface is fjgi0): # /etc/opt/FJSVla/bin/fjla stat fjgi0 -i 5 Oct 05 17:20:14 2004 Aggregator: fjgi0 Mode: DA Name Status Ipkts Ierrs Opkts Oerrs %Ipkt %Opkt Total 7658459 0 7193 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 63

    Chapter 4 LinkAggregati on Feature 4.3 Notes This section explains notes for using the LinkAggregation function. ● LACP (dynamic LinkAggregation function) is not supported. ● Only TCP/IP connection is supported. ● Do not run FJVTS when LinkAggregation is being used. ● If VLAN interface with LinkAggregation function enabled is used, the foll ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 64

    Chapter 5 Troubleshooting The following should be checked first to troubleshoot a problem. Is the drive r software insta lled correctly ? Execute "pkginfo -l FJSVgid" and “pkginfo –l FJSVgidx”command to check the driver installation status. If the driver package is not found or is not installed correctly, install the driver packages ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 65

    ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 66

    Appendix A Messages This chapter explains messages from the FUJITSU PCI GigabitEthernet driver A.1 Console Messages Console messages from the FUJITSU PCI GigabitEthernet driver are listed in Table A.1.1. Table A.1.1 Console Messages of the FUJITSU PCI GigabitEthernet driver No Message Cause Workaround 1 network connection down Link is down Check th ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 67

    Appendix A Messages No Message Cause Workaround [E] Master : Communicating as Master Slave : Communicating as Slave 3 Illegal value for [ParameterName]. An error was found with a parameter defined in the fjgi.conf file. Check whether the value is set correctly in the file. 4 soft state alloc failed. Driver internal resources cannot be obtained. Ins ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 68

    A.1 Consol e Messages No Message Cause Workaround 13 Unable to map adapter registers. Mapping of the adapter registers failed. 14 ddi_get_iblock_cookie-ERROR 15 Unable to install interrupt routine. The driver could not allocate interrupt resources. 16 ddi_create_minor_node failed Creation of a device file failed. 17 ATTACH failed The driver wa s no ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 69

    Appendix A Messages No Message Cause Workaround 39 Role not available for fiber adapters Role setting is no supported with PW008GE4/PW0G8GE1/SE0X7GD2X . Remove Role_A parameter in the fjgi.conf file. 40 Can't judge T or SX !! The adapter type cannot be recognized. Check whether the system is supported. Since there is possibility of hard abnorm ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 70

    A.2 Comman d Messages Message Meaning Workaround fjgi_device_check: fjgi_hw_init failed ! An error occurred during initialization of the adapter. There is a possibility of hardware abnormalities. Please replace the adapter. pci_config_setup_failed The driver could not allocate sufficient PCI configuration space. There is a possibility of the resour ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 71

    Appendix A Messages No Message Cause Workaround 8 fjla init: "XX" does not exist. The interface "XX" does not exist. Specify interfaces that exist on the system. 9 fjla init: Invalid mode number ("XX"). The distributed mode "XX" is incorrect. Specify correct distributed mode (1, 2 or 3). 10 fjla init: An inpu ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 72

    Appendix B On-Board Diagnostics This appendix explains the on-board diagnostics function. - Location o f the LEDs(PW008 GE4/PW008GE5) The following figures show the location of the LEDs. Figure B.1 1000Base-S X (PW008GE4) Figure B.2 10/100/100 0Base-T (PW00 8GE5) - Meaning of the LEDs(PW008G E4/PW008GE5) 1000M LED indicates the following operation ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 73

    Appendix B On-Board Dia gnostics ACT LED indicates the following operation status. ACT LED Descriptio n Green lighting The adapter is transmitting or receiving network traffic. Off There is no network traffic. - Location o f the LEDs(PW0G8 GE1/SE0X7GD2X) The following figures show t he location of the LEDs. Figure B.3 1000Base-S X (PW0G8GE1) Figure ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 74

    - Location o f the LEDs(PW0G8 GE2) The following figures show the location of the LEDs. Figure B.5 10/100/100 0Base-T (PW0G 8GE2) - Meaning of the LEDs(PW0G8G E2) 1000M LED indicates the following operation status. 1000M LED Descriptio n Amber lighting The adapter is connected to a 1000Mbps network and is in the state which can communicate. Off The ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 75

    Appendix B On-Board Dia gnostics - Location o f the LEDs(SE0X7 GD1X) The following figures show the location of the LEDs. Figure B.6 10/100/100 0Base-T * 2po rts (SE0X7G D1X) - Meaning of the LEDs(SE0X7G D1X) 1000M LED indicates the following operation status. 1000M LED Descriptio n Amber lighting The adapter is connected to a 1000Mbps network and ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 76

    - Location o f the LEDs(PW008 QG1/SE0X7GQ1X) The following figures show the location of the LEDs. Figure B.7 1000Base-T * 4ports (PW 008QG1) Figure B.8 1000Base-T * 4ports (SE 0X7GQ1X) - Meaning of the LEDs(PW008Q G1/SE0X7GQ1X) LINK LED(White LED in Figure B.7/8) indicates the following operation status. LINK LED Descriptio n Amber lighting The ada ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 77

    ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 78

    Appendix C Using GigabitEthernet in a Cluster Environment This Appendix outlines the supported functions and setup procedure for the FUJITSU PCI GigabitEthernet 3.0 interface when used in a cluster environment. C.1 Cluster Environment Support The FUJITSU PCI GigabitEthernet 3.0 adapter supports the following cluster features: ● Operation standby ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 79

    Appendix C Using Gigabi tEthernet i n a Cluste r Environment C.3 Notes ● SynfinityCluster 2.0 or later or PRIMECLUSTER 4.1 or later is required when using the FUJITSU PCI GigabitEthernet interface. If an earlier version of cluster software is used, GigabitEthernet cannot be used as the private LAN or for IP address fail-over on a public LAN. ● ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 80

    Appendix D PCI Slot Number and Device Name The appendix provides the PCI slot numb er and device name matrix for the following PRIMEPOWER/GP7000F models. ● GP7000F Model200 ● GP7000F Model200R ● GP7000F Model400A/400R ● GP7000F Model400 ● GP7000F Model600 ● GP7000F Model600R ● PRIMEPOWER 1 (1U rackmount) ● PRIMEPOWER 100 (pedestal) ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 81

    Appendix D PCI Slot Num ber and Dev ice Name ● GP7000F Model200R Slot Numbe r Device Nam e PCI#1 /pci@17,2000/*@1 PCI#2 /pci@16,2000/*@1 PCI#3 /pci@17,4000/*@2 PCI#4 /pci@16,4000/*@2 PCI#5 /pci@16,4000/*@4 PCI#6 /pci@16,4000/*@5 ● GP7000F Model400A/400R Slot Numbe r Device Nam e 00-PCI#1 /pci@17,2000/*@1 00-PCI#2 /pci@16,2000/*@1 00-PCI#3 /pci@ ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 82

    Appendix D PCI Slot Num ber and Dev ice Name Slot Numbe r Device Nam e PCI#12 /pci@1c,4000/*@4 PCI#13 /pci@1c,2000/*@1 ● GP7000F Model600R Slot Numbe r Device Nam e PCI#1 /pci@1f,4000/*@2 PCI#2 /pci@1f,2000/*@1 PCI#3 /pci@1c,4000/*@2 PCI#4 /pci@1e,4000/*@2 PCI#5 /pci@1e,4000/*@3 PCI#6 /pci@1e,4000/*@4 PCI#7 /pci@1c,2000/*@1 PCI#8 /pci@1d,4000/*@2 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 83

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 250 (2U rack-mount) Slot Numbe r Device Nam e PCI#0 /pci@83,2000/*@2 PCI#1 /pci@83,4000/*@3 PCI#2 /pci@83,4000/*@4 ● PRIMEPOWER 250 (4U rack-mount) Slot Numbe r Device Nam e PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,2000/*@2 PCI#2 /pci@80,4000/*@3 PCI#3 /pci@80,4000/*@4 PCI#4 /pci@80,4000/*@5 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 84

    Appendix D PCI Slot Num ber and Dev ice Name Slot Numbe r Device Nam e 01-PCI#5 /pci@11,4000/*@5 ● PRIMEPOWER 450 (pedestal, 7U rack-mount) Slot Numbe r Device Nam e PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,4000/*@3 PCI#2 /pci@80,4000/*@4 PCI#3 /pci@80,4000/*@5 PCI#4 /pci@82,2000/*@1 PCI#5 /pci@82,4000/*@3 PCI#6 /pci@82,4000/*@4 PCI#7 /pci@82,4000/*@ ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 85

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 650 (rackmount) Board Numb er Slot Numbe r Dev ice Name PCI#0 /pci@84,2000/*@1 PCI#1 /pci@84,4000/*@1 PCI#2 /pci@84,4000/*@2 PCI#3 /pci@84,4000/*@3 PCI#4 /pci@85,2000/*@1 PCI#5 /pci@85,4000/*@1 PCI#6 /pci@85,4000/*@2 SB#0 PCI#7 /pci@85,4000/*@3 PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,4000/*@1 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 86

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 850 (rackmount) Board Numb er Slot Numbe r Device Nam e PCI#0 /pci@84,2000/*@1 PCI#1 /pci@84,4000/*@1 PCI#2 /pci@84,4000/*@2 PCI#3 /pci@84,4000/*@3 PCI#4 /pci@85,2000/*@1 PCI#5 /pci@85,4000/*@1 PCI#6 /pci@85,4000/*@2 SB#0 PCI#7 /pci@85,4000/*@3 PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,4000/*@1 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 87

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 900 (Physical Partitioning) Board Numb er; Slot Numbe r Device Nam e PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,4000/*@2 PCI#2 /pci@81,2000/*@1 PCI#3 /pci@81,4000/*@2 PCI#4 /pci@81,4000/*@3 PCI#5 /pci@82,2000/*@1 PCI#6 /pci@82,4000/*@2 SB#0 PCI#7 /pci@82,4000/*@3 PCI#0 /pci@84,2000/*@1 PCI#1 /pc ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 88

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Name PCI#0 /pci@c4,2000/*@1 PCI#1 /pci@c4,4000/*@2 PCI#2 /pci@c4,4000/*@3 PCI#3 /pci@c5,2000/*@1 PCI#4 /pci@c5,4000/*@2 PCI#5 /pci@c5,4000/*@3 PCI#6 /pci@c5,4000/*@4 PCI#7 /pci@e6,2000/*@1 PCI#8 /pci@e6,4000/*@2 PCI-BOX#0 (connected to SB#0) PCI#9 /pci@e6,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 89

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0A /pci@90,2000/*@1 PCI#0B /pci@90,4000/*@2 PCI#1A /pci@91,2000/*@1 PCI#1B /pci@91,4000/*@2 PCI#3A /pci@93,2000/*@1 SB#2 PCI#3B /pci@93,4000/*@2 PCI#0A /pci@98,2000/*@1 PCI#0B /pci@98,4000/*@2 PCI#1A /pci@99,2000/*@1 PCI#1B /pci@99,4000/*@2 PCI#3A /pci@9b,2000/* ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 90

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Name PCI#0 /pci@84,2000/*@1 PCI#1 /pci@84,4000/*@2 PCI#2 /pci@84,4000/*@3 PCI#3 /pci@85,2000/*@1 PCI#4 /pci@85,4000/*@2 PCI#5 /pci@85,4000/*@3 PCI#6 /pci@85,4000/*@4 PCI#7 /pci@86,2000/*@1 PCI#8 /pci@86,4000/*@2 PCI-BOX#0 (connected to SB#0) PCI#9 /pci@86,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 91

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Name PCI#0 /pci@98,2000/*@1 PCI#1 /pci@98,4000/*@2 PCI#2 /pci@99,2000/*@1 PCI#3 /pci@99,4000/*@2 PCI#4 /pci@99,4000/*@3 PCI#5 /pci@9a,2000/*@1 PCI#6 /pci@9a,4000/*@2 SB#3 PCI#7 /pci@9a,4000/*@3 PCI#0 /pci@9c,2000/*@1 PCI#1 /pci@9c,4000/*@2 PCI#2 /pci@9c,4000/*@3 PCI#3 / ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 92

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Name PCI#0 /pci@cc,2000/*@1 PCI#1 /pci@cc,4000/*@2 PCI#2 /pci@cc,4000/*@3 PCI#3 /pci@cd,2000/*@1 PCI#4 /pci@cd,4000/*@2 PCI#5 /pci@cd,4000/*@3 PCI#6 /pci@cd,4000/*@4 PCI#7 /pci@ee,2000/*@1 PCI#8 /pci@ee,4000/*@2 PCI-BOX#0 (connected to SB#1) PCI#9 /pci@ee,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 93

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 2000,GP7000F Model2000 Board Numb er Slot Numbe r Device Nam e PCI#0A /pci@80,2000/*@1 PCI#0B /pci@80,4000/*@2 PCI#1A /pci@81,2000/*@1 PCI#1B /pci@81,4000/*@2 PCI#3A /pci@83,2000/*@1 SB#0 PCI#3B /pci@83,4000/*@2 PCI#0A /pci@84,2000/*@1 PCI#0B /pci@84,4000/*@2 PCI#1A /pci@85,2000/*@1 PCI#1B ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 94

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0A /pci@a0,2000/*@1 PCI#0B /pci@a0,4000/*@2 PCI#1A /pci@a1,2000/*@1 PCI#1B /pci@a1,4000/*@2 PCI#3A /pci@a3,2000/*@1 SB#8 PCI#3B /pci@a3,4000/*@2 PCI#0A /pci@a4,2000/*@1 PCI#0B /pci@a4,4000/*@2 PCI#1A /pci@a5,2000/*@1 PCI#1B /pci@a5,4000/*@2 PCI#3A /pci@a7,2000/* ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 95

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Numbe r Device Nam e PCI#0A /pci@c0,2000/*@1 PCI#0B /pci@c0,4000/*@2 PCI#1A /pci@c1,2000/*@1 PCI#1B /pci@c1,4000/*@2 PCI#3A /pci@c3,2000/*@1 SB#16 PCI#3B /pci@c3,4000/*@2 PCI#0A /pci@c4,2000/*@1 PCI#0B /pci@c4,4000/*@2 PCI#1A /pci@c5,2000/*@1 PCI#1B /pci@c5,4000/*@2 PCI#3A /pci@c7,2000 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 96

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0A /pci@e0,2000/*@1 PCI#0B /pci@e0,4000/*@2 PCI#1A /pci@e1,2000/*@1 PCI#1B /pci@e1,4000/*@2 PCI#3A /pci@e3,2000/*@1 SB#24 PCI#3B /pci@e3,4000/*@2 PCI#0A /pci@e4,2000/*@1 PCI#0B /pci@e4,4000/*@2 PCI#1A /pci@e5,2000/*@1 PCI#1B /pci@e5,4000/*@2 PCI#3A /pci@e7,2000/ ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 97

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 2500/HPC2500 (Physical Partitioning) Board Numb er Slot Numbe r Device Nam e PCI#0 /pci@80,2000/*@1 PCI#1 /pci@80,4000/*@2 PCI#2 /pci@80,4000/*@3 PCI#3 /pci@81,2000/*@1 PCI#4 /pci@81,4000/*@2 PCI#5 /pci@81,4000/*@3 PCI#6 /pci@81,4000/*@4 PCI#7 /pci@82,2000/*@1 PCI#8 /pci@82,4000/*@2 PCI-BO ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 98

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@90,2000/*@1 PCI#1 /pci@90,4000/*@2 PCI#2 /pci@90,4000/*@3 PCI#3 /pci@91,2000/*@1 PCI#4 /pci@91,4000/*@2 PCI#5 /pci@91,4000/*@3 PCI#6 /pci@91,4000/*@4 PCI#7 /pci@92,2000/*@1 PCI#8 /pci@92,4000/*@2 PCI-BOX#0 (connected to SB#2) PCI#9 /pci@92,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 99

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@a0,2000/*@1 PCI#1 /pci@a0,4000/*@2 PCI#2 /pci@a0,4000/*@3 PCI#3 /pci@a1,2000/*@1 PCI#4 /pci@a1,4000/*@2 PCI#5 /pci@a1,4000/*@3 PCI#6 /pci@a1,4000/*@4 PCI#7 /pci@a2,2000/*@1 PCI#8 /pci@a2,4000/*@2 PCI-BOX#0 (connected to SB#4) PCI#9 /pci@a2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 100

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@b0,2000/*@1 PCI#1 /pci@b0,4000/*@2 PCI#2 /pci@b0,4000/*@3 PCI#3 /pci@b1,2000/*@1 PCI#4 /pci@b1,4000/*@2 PCI#5 /pci@b1,4000/*@3 PCI#6 /pci@b1,4000/*@4 PCI#7 /pci@b2,2000/*@1 PCI#8 /pci@b2,4000/*@2 PCI-BOX#0 (connected to SB#6) PCI#9 /pci@b2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 101

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@c0,2000/*@1 PCI#1 /pci@c0,4000/*@2 PCI#2 /pci@c0,4000/*@3 PCI#3 /pci@c1,2000/*@1 PCI#4 /pci@c1,4000/*@2 PCI#5 /pci@c1,4000/*@3 PCI#6 /pci@c1,4000/*@4 PCI#7 /pci@c2,2000/*@1 PCI#8 /pci@c2,4000/*@2 PCI-BOX#0 (connected to SB#8) PCI#9 /pci@c2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 102

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@d0,2000/*@1 PCI#1 /pci@d0,4000/*@2 PCI#2 /pci@d0,4000/*@3 PCI#3 /pci@d1,2000/*@1 PCI#4 /pci@d1,4000/*@2 PCI#5 /pci@d1,4000/*@3 PCI#6 /pci@d1,4000/*@4 PCI#7 /pci@d2,2000/*@1 PCI#8 /pci@d2,4000/*@2 PCI-BOX#0 (connected to SB#a) PCI#9 /pci@d2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 103

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@e0,2000/*@1 PCI#1 /pci@e0,4000/*@2 PCI#2 /pci@e0,4000/*@3 PCI#3 /pci@e1,2000/*@1 PCI#4 /pci@e1,4000/*@2 PCI#5 /pci@e1,4000/*@3 PCI#6 /pci@e1,4000/*@4 PCI#7 /pci@e2,2000/*@1 PCI#8 /pci@e2,4000/*@2 PCI-BOX#0 (connected to SB#c) PCI#9 /pci@e2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 104

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#0 /pci@f0,2000/*@1 PCI#1 /pci@f0,4000/*@2 PCI#2 /pci@f0,4000/*@3 PCI#3 /pci@f1,2000/*@1 PCI#4 /pci@f1,4000/*@2 PCI#5 /pci@f1,4000/*@3 PCI-BOX#0 (connected to SB#e) PCI#6 /pci@f1,4000/*@4 PCI#7 /pci@f2,2000/*@1 PCI#8 /pci@f2,4000/*@2 PCI#9 /pci@f2,4000/*@3 PCI#0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 105

    Appendix D PCI Slot Num ber and Dev ice Name ● PRIMEPOWER 2500 (Extended Partitioning) Board Numb er; Slot Numbe r Device Nam e PCI#0 /pci@84,2000/*@1 PCI#1 /pci@84,4000/*@2 PCI#2 /pci@84,4000/*@3 PCI#3 /pci@85,2000/*@1 PCI#4 /pci@85,4000/*@2 PCI#5 /pci@85,4000/*@3 PCI#6 /pci@85,4000/*@4 PCI#7 /pci@86,2000/*@1 PCI#8 /pci@86,4000/*@2 PCI-BOX#0 (co ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 106

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Nam e PCI#0 /pci@a4,2000/*@1 PCI#1 /pci@a4,4000/*@2 PCI#2 /pci@a4,4000/*@3 PCI#3 /pci@a5,2000/*@1 PCI#4 /pci@a5,4000/*@2 PCI#5 /pci@a5,4000/*@3 PCI#6 /pci@a5,4000/*@4 PCI#7 /pci@a6,2000/*@1 PCI#8 /pci@a6,4000/*@2 PCI-BOX#0 (connected to SB#4) PCI#9 /pci@a6,4000/*@3 PCI# ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 107

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Nam e PCI#0 /pci@c0,2000/*@1 PCI#1 /pci@c0,4000/*@2 PCI#2 /pci@c0,4000/*@3 PCI#3 /pci@c1,2000/*@1 PCI#4 /pci@c1,4000/*@2 PCI#5 /pci@c1,4000/*@3 PCI#6 /pci@c1,4000/*@4 PCI#7 /pci@c2,2000/*@1 PCI#8 /pci@c2,4000/*@2 PCI-BOX#0 (connected to SB#8) PCI#9 /pci@c2,4000/*@3 PCI# ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 108

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er; Slot Numbe r Device Nam e PCI#0 /pci@e0,2000/*@1 PCI#1 /pci@e0,4000/*@2 PCI#2 /pci@e0,4000/*@3 PCI#3 /pci@e1,2000/*@1 PCI#4 /pci@e1,4000/*@2 PCI#5 /pci@e1,4000/*@3 PCI#6 /pci@e1,4000/*@4 PCI#7 /pci@e2,2000/*@1 PCI#8 /pci@e2,4000/*@2 PCI-BOX#0 (connected to SB#c) PCI#9 /pci@e2,4000/*@3 PCI# ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 109

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#1-PCIX3 /pci@0,600000/pci@0/pci@9/pci@0/pci@9/pci@0/****@4 PCI#1-PCIX4 /pci@0,600000/pci@0/pci@9/pci@0/pci@9/pci@0,1/****@4 PCI#1-PCIE1 /pci@0,600000/pci@0/pci@9/pci@0/pci@1/pci@0/pci@0/****@0 PCI#1-PCIE2 /pci@0,600000/pci@0/pci@9/pci@0/pci@1/pci@0/pci@1/****@0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 110

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#4-PCIE6 /pci@3,700000/pci@0/pci@9/pci@0/pci@9/****@0 PCI#0 /pci@10,600000/pci@0/pci@8/pci@0,1/****@1 Basic PCI Slot PCI#1 /pci@10,600000/pci@0/pci@9/****@0 PCI#1-PCIX1 /pci@10,600000/pci@0/pci@9/pci@0/pci@1/pci@0/****@4 PCI#1-PCIX2 /pci@10,600000/pci@0/pci@9/pci ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 111

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Number Device Nam e PCI#4-PCIX3 /pci@13,700000/pci@0/pci@9/pci@0/****@4 PCI#4-PCIX4 /pci@13,700000/pci@0/pci@9/pci@0,1/****@4 PCI#4-PCIE1 /pci@13,700000/pci@0/pci@1/pci@0/pci@0/****@0 PCI#4-PCIE2 /pci@13,700000/pci@0/pci@1/pci@0/pci@1/****@0 PCI#4-PCIE3 /pci@13,700000/pci@0/pci@1/pci@0 ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 112

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Numbe r Device Name PCI#5-PCIX5 /pci@5,700000/pci@0/pci@8/pci@0/****@4 PCI#5-PCIX6 /pci@5,700000/pci@0/pci@8/pci@0,1/****@4 PCI#5-PCIX3 /pci@5,700000/pci@0/pci@9/pci@0/****@4 PCI#5-PCIX4 /pci@5,700000/pci@0/pci@9/pci@0,1/****@4 PCI#5-PCIE1 /pci@5,700000/pci@0/pci@1/pci@0/pci@0/****@0 P ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 113

    Appendix D PCI Slot Num ber and Dev ice Name Board Numb er Slot Numbe r Device Name PCI#3-PCIX6 /pci@13,700000/pci@0/pci@8/pci@0,1/****@4 PCI#3-PCIX3 /pci@13,700000/pci@0/pci@9/pci@0/****@4 PCI#3-PCIX4 /pci@13,700000/pci@0/pci@9/pci@0,1/****@4 PCI#3-PCIE1 /pci@13,700000/pci@0/pci@1/pci@0/pci@0/****@0 PCI#3-PCIE2 /pci@13,700000/pci@0/pci@1/pci@0/pci ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 114

    Appendix E Available Switches This appendix shows switches tested with FUJITSU PCI GigabitEthernet 3.0 (as of January 2007). Table E.1 With FUJITSU PCI GigabitEthernet 3.0 (PW008GE4/PW0G8GE1/SE0X7GD2X) Product Na me Connection Jumbo Frame Note FUJITSU SH4000, SB7300, SR8800, SH4322G OK OK with SH4322G only With SB7300, turn off the Autonegotiation ...

  • Fujitsu PCI GigabitEthernet 3.0 - page 115

    Appendix E Available Sw itches Table E.4 IEEE802.3 LinkAggregation capable switches Product Na me Connection Available Function Name FUJITSU SH4322G OK LinkAggregation function 3Com Superstack 3 OK LinkAggregation function Hewlett Packard ProCurve 8000m OK Load Balancing function Extreme Networks Summit 1i, 7i OK Load Sharing function CISCO Systems ...

Manufacturer Fujitsu Category Network Card

Documents that we receive from a manufacturer of a Fujitsu PCI GigabitEthernet 3.0 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- PCI GigabitEthernet 3.0 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu PCI GigabitEthernet 3.0
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu PCI GigabitEthernet 3.0.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu PCI GigabitEthernet 3.0, service manual, brief instructions and user manuals Fujitsu PCI GigabitEthernet 3.0. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu PCI GigabitEthernet 3.0.

Similar manuals

A complete manual for the device Fujitsu PCI GigabitEthernet 3.0, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu PCI GigabitEthernet 3.0 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu PCI GigabitEthernet 3.0.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu PCI GigabitEthernet 3.0 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu PCI GigabitEthernet 3.0, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu PCI GigabitEthernet 3.0, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu PCI GigabitEthernet 3.0 - which should help us in our first steps of using Fujitsu PCI GigabitEthernet 3.0
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu PCI GigabitEthernet 3.0
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu PCI GigabitEthernet 3.0 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu PCI GigabitEthernet 3.0?

Use the form below

If you did not solve your problem by using a manual Fujitsu PCI GigabitEthernet 3.0, ask a question using the form below. If a user had a similar problem with Fujitsu PCI GigabitEthernet 3.0 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)