English dropdown-ico

Manual Yard-Man 7200-0

16 pages 3.91 mb
Download

Go to site of 16

Summary
  • Yard-Man 7200-0 - page 1

    and / f .I I ~ ~ 'r ~ " -- I YARD. MAN CO.. P. O. BOX 36940 CLEVELAND, OHIO 44136 1410 West Ganson Street -Jackson, Michigan 49202 0611-7588 PRINTED !N U.S.A. ...

  • Yard-Man 7200-0 - page 2

    Your SNOW THROWER is a precision piece of snow throwing equipment. Engineering skill and experience have been combined to provide the ultimate in safety and efficiency. As with any type of power equipment, carelessness or error on the part of the operator can result in injury. EXERCISE EXTREME CAUTION AT ALL TIMES. 1.. READ THE OWNER'S MANUAL ...

  • Yard-Man 7200-0 - page 3

    MA1NTENAN CE~ FREE OPERATION , GENERAL SNOW~THROWING 1.~ Always keep area to be cleaned cleared before~owfall~. . 2.~. Always start engine with machine on level surface with master clutch disengaged: After starting, let engine warm up several ';;;.. ""i" '-. minutes at slow speed before starting to remove ~now~ Ifinachine i ...

  • Yard-Man 7200-0 - page 4

    UNPACKING AND SET-UP 1. Before assembling your Snow Thrower be sure all hardware, parts, and instructions have been removed from the carton. , ...:' ':;.' '- 2. Assemble right and left handle tubes to the unit with bolts, lockwashers, and flat washers. Do not tighten.3. Assemble handle panel assembly to the under side of right a ...

  • Yard-Man 7200-0 - page 5

    BEFORE STARTING ENGINE STARTING ENGINE " : 'f" Shift the master clutch control to the Neutral position. Move the choke lever to full choke position. Move speed control lever to run position. Start the engine by pulling rapidly on the recoil starter rope. As the engine starts and begins to warm up, gradually return the choke lever to ...

  • Yard-Man 7200-0 - page 6

    OPERATION OF CONTROLS MASTERCLUrCH CONTROL The master clutch control is located on handle panel and IS used to engage, all power~Select:8 forward speed or rever~ " ' ",,'c,';""...c"":, with shift lever, then release master clutch control and push , '.. c, ,," ,. - f,orward to engage ?rive diS?: ...

  • Yard-Man 7200-0 - page 7

    . . REPLACING SAFETY SHEAR BOLT CHUTE CHAIN AND-ADJUSTMENT To tight~n the chute chain, rotate the chute all the way to the left, until the adjustment bolt is accessible. Tighten the adjustment nut to tighten the chain. ..' : ." .,,' , CAUTION: Chain must be kept snug on chute housing. " CHUTE CABLE ADJUSTMENT SHIFT PANEL ADJUSTM ...

  • Yard-Man 7200-0 - page 8

    ...

  • Yard-Man 7200-0 - page 9

    ...

  • Yard-Man 7200-0 - page 10

    PARTS LIST MODEL 7200-0 Your SNOW THROWER is right hand (R.H.I or left hand (L.H.I as you operate machine. 1 2 :I 4 6 6 7 8 9 10 11 12 13 14 16 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 48 59 60 61 64 65 66 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 ...

  • Yard-Man 7200-0 - page 11

    P ARTS LIST REF. PART REF. NO. NO. DESCRIPTION NO. t 1654-31 Chain -W/Connactlng Link 22 No.41 x 28 pitches 23 2 1624-192 Spacer-Gear Sprocket 24 -3 1652-114 Baaring-Needla7/16x 1/2 L. 25 4 1149-5 A-mbly -Gaar & Sprocket W/Bearlng 26~,c (Included Ref. No.3) .6 42342 Nut -Hex Lock 3/8.16 (Eslok) 27 6 1008 Washer -SA.E. 3/8 28 7 1646-24 Key -Wood ...

  • Yard-Man 7200-0 - page 12

    IDLER LINKAGE ADJUSTMENT .:.~. :a~.!...L:. To check the adjustment, return the master clutch lever to neutral position and pull engine recoil over to see if belt is not driving. If belt does not release, lower the adjustment link slightly below center or until belt does release in " , neutral. These adjustments must also be checked when belt i ...

  • Yard-Man 7200-0 - page 13

    LUBRICA TION- CHANGING ENGINE OIL LUBRICATION POINTS lUBRICATE THE PARTS PERIODICAllY AS IllUS-TRATED. The following points are to be lubricated every five hours of operation with SAE 20 weight light duty oil. unless otherwise noted. 1. Spherical Bearings (Both Sides) 2. Wheels 3. Discharge Spout 4. Blower Housing 5. Reel Chain' .;': 6. C ...

  • Yard-Man 7200-0 - page 14

    CHUTE CABLE REPLACEMENT OR REPAIR cable roller bracket and down to the right hole in the top of the blower housing. C. Turn the cable pulley with the cable bolt toward the bottom of the blower housing. , , " .' ' . D. Put the ends of the cable up through the holes in the bottom of the cable pulley and cross the ends up and over the ...

  • Yard-Man 7200-0 - page 15

    1~ .~';:;j 15 ...

  • Yard-Man 7200-0 - page 16

    30" SNOW THROWER you enjoy these outstanding features ~ 7/73 ...

Manufacturer Yard-Man Category Snow Blower

Documents that we receive from a manufacturer of a Yard-Man 7200-0 can be divided into several groups. They are, among others:
- Yard-Man technical drawings
- 7200-0 manuals
- Yard-Man product data sheets
- information booklets
- or energy labels Yard-Man 7200-0
All of them are important, but the most important information from the point of view of use of the device are in the user manual Yard-Man 7200-0.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Yard-Man 7200-0, service manual, brief instructions and user manuals Yard-Man 7200-0. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Yard-Man 7200-0.

Similar manuals

A complete manual for the device Yard-Man 7200-0, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Yard-Man 7200-0 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Yard-Man 7200-0.

A complete Yard-Man manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Yard-Man 7200-0 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Yard-Man 7200-0, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Yard-Man 7200-0, that we can find in the current document
3. Tips how to use the basic functions of the device Yard-Man 7200-0 - which should help us in our first steps of using Yard-Man 7200-0
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Yard-Man 7200-0
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Yard-Man 7200-0 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Yard-Man 7200-0?

Use the form below

If you did not solve your problem by using a manual Yard-Man 7200-0, ask a question using the form below. If a user had a similar problem with Yard-Man 7200-0 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)