English dropdown-ico

Manual Genelec 8240A

16 pages 0.84 mb
Download

Go to site of 16

Summary
  • Genelec 8240A - page 1

    d s p Operating Manual 8240A and 8250A DSP Loudspeakers ...

  • Genelec 8240A - page 2

    2 ...

  • Genelec 8240A - page 3

    3 INTRODUCTION Congratulations and a thank-you for the purchase of this Genelec 8200 Series DSP Loudspeaker . These systems are designed to integrate easily into the digital production environment. There are several ways to configure and operate the DSP loudspeakers for a wide variety of high quality audio applications. The loudspeakers also have a ...

  • Genelec 8240A - page 4

    4 harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this ...

  • Genelec 8240A - page 5

    5 USING THE 8240A AND 8250A IN ST AND -AL ONE MODE The 8240A and 8250A accept both analogue line level input signals and AES/EBU formatted digital input signals. When the 8240A and 8250A are not connected to Genelec loudspeaker control network, they operate in the stand-alone mode. However , settings made with the Genelec Loudspeaker Manager softwa ...

  • Genelec 8240A - page 6

    6 “DIGIT AL IN AES/EBU” connector Use this female XLR connector for AES/EBU formatted digital audio input signals. This input is selected automatically when a valid digital audio signal is present, and overrides the analogue input. Depending on the digital hardware, transmission of a 192 kHz sample rate is achieved using a double speed, single ...

  • Genelec 8240A - page 7

    7 The overload light (red) is activated by several events, • exceeding the maximum input range of the analog input • exceeding the maximum input range of the digital input with large probability • exceeding the output capacity of the power amplifier (clipping in the power amplifier) and thermal overload of the power amplifier or loudspeaker d ...

  • Genelec 8240A - page 8

    8 Mounting options The vibration insulating Isolation Positioner/Decoupler™ (Iso-P od™) table stand allows tilting of the loudspeaker for correct alignment of the acoustic axis. The stand can be attached to three mounting points allowing vertical and symmetrical horizontal positioning. Genelec 8240A and 8250A can be fitted to König & Meyer ...

  • Genelec 8240A - page 9

    9 This feature is designed to compensate for the boost often occurring at this frequency range when the loudspeaker is placed upon a meter bridge, table or similar reflective surface. T reble Tilt control T reble Tilt control (switches 6 and 7) allows adjusting the treble response above 5 kHz by +2 dB, -2 dB or -4 dB, which can be used for correcti ...

  • Genelec 8240A - page 10

    10 F unctions on Switch Group 2 Stored / Manual Ctrl This allows the selection between two basic methods of controlling the loudspeaker in the stand-alone mode. “MANUAL CTRL ” refers to controlling the loudspeaker using the controls on the loudspeaker’s back panel. The “STORED” refers to using settings stored inside the memory of the loud ...

  • Genelec 8240A - page 11

    11 • Connect the GLM Control Network to the main loudspeakers. • Make a System Setup in GLM. It will consist of main loudspeakers as this is all the network can see, so suitable Rapid Cabling Presets are “Stereo Pair (Analog)” and “5.0 Surround System (Analog)”. • Run AutoCal and review and the results to check for large dips at or ab ...

  • Genelec 8240A - page 12

    12 Guarantee Genelec 8240A and 8250A are supplied with one year guarantee against manufacturing faults or defects that might alter the performance of the loudspeakers. Refer to supplier for full sales and guarantee terms. 8240A Accessories Order code Description 8000-408 Floor stand (K&M 26740-000-58) 8000-401B Wall mount, black (K&M 24180- ...

  • Genelec 8240A - page 13

    13 SPECIFICA TIONS 8240A 8250A Lower cut-off frequency , -3 dB Upper cut-off frequency , -3 dB ≤ 45 Hz ≥ 21 kHz ≤ 35 Hz ≥ 21 kHz F ree field frequency response of system (± 1.0 dB) 48 Hz - 20 kHz 38 Hz - 20 kHz Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz @ 1 m @0.5 m ≥ 105 dB SPL ≥ ...

  • Genelec 8240A - page 14

    14 8240A 8250A Analog audio input connector XLR female, pin 1 gnd, pin 2 +, pin 3 - Analog audio input impedance 10 kOhm balanced Input level for maximum short term output of 100 dB SPL @ 1m Adjustable from +6 to -6 dBu Crossover frequency , Bass/T reble 3.0 kHz 1.8 kHz T reble Tilt control operating range in 2 dB steps +2 to -4 dB & MUTE @ 15 ...

  • Genelec 8240A - page 15

    15 The curves above show the effect of the “Bass Tilt”, “T reble Tilt”, “Desktop Low F requency” and “Bass Roll-Off ” controls on the free field response of the 8240A. The upper curve group shows the horizontal directivity characteristics of the 8240A measured at 1 m. The lower curve shows the system's power response. The upper ...

  • Genelec 8240A - page 16

    Genelec Document D0048R001a. Copyright Genelec Oy 3.2006. All data subject to change ...

Manufacturer Genelec Category Portable Speaker

Documents that we receive from a manufacturer of a Genelec 8240A can be divided into several groups. They are, among others:
- Genelec technical drawings
- 8240A manuals
- Genelec product data sheets
- information booklets
- or energy labels Genelec 8240A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Genelec 8240A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Genelec 8240A, service manual, brief instructions and user manuals Genelec 8240A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Genelec 8240A.

Similar manuals

A complete manual for the device Genelec 8240A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Genelec 8240A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Genelec 8240A.

A complete Genelec manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Genelec 8240A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Genelec 8240A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Genelec 8240A, that we can find in the current document
3. Tips how to use the basic functions of the device Genelec 8240A - which should help us in our first steps of using Genelec 8240A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Genelec 8240A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Genelec 8240A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Genelec 8240A?

Use the form below

If you did not solve your problem by using a manual Genelec 8240A, ask a question using the form below. If a user had a similar problem with Genelec 8240A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)