English dropdown-ico

Manual Krell Industries KST100

16 pages 0.87 mb
Download

Go to site of 16

Summary
  • Krell Industries KST100 - page 1

    ...

  • Krell Industries KST100 - page 2

    A, INTRODUCTION Thank you for your purchase of the KRELL KST-100 poweramplifier. This amplifier represents the latest evolution ~n amplifier technology and incorporates many innovative design features. To obtain the best performance from. your KST-100, careful attention sfiould be paid to placement, installation and operation. A thorough understand ...

  • Krell Industries KST100 - page 3

    TABLE OF CONTENTS 4 UNPACKING AND ASSEMBLY 5 BASIC INSTALLATION AND OPERATION 6 INPUT AND OUTPUT CONNECTIONS 8 AMPLIFIER OPERATION 9 PROTECTION CIRCUITRY 10 MONAURAL CONVERSION OPERATION 11 REAR PANEL DESCRIPTIONS 12 QUESTIONS AND ANSWERS 14 SPECIFICATIONS 15 WARRANTY AND SERVICE INFORMATION 3 ...

  • Krell Industries KST100 - page 4

    B. UNPACKING AND ASSEMBLY NOTE: Do to the weight of the KST-100 it is s.trongly advised that unpacking and placement is completed by at least two individuals. 1. Open the box on one end. 2. Fold back the flaps on all four sides of the box and carefully roll it over on to the exposed end. 3. Pull the box straight up and off exposing the foam packing ...

  • Krell Industries KST100 - page 5

    C. BASIC INSTALLATION AND OPERATION 1. Place the KST-100 on a firm level surface away from excessive dirt or moisture. Ideally the amplifier should be placed as close to. the speakers as possible. It is always preferable to run long_ interconnect cables to the amplifier and keep speaker calSle length to.a minimum= Speal~er cable does add an impedan ...

  • Krell Industries KST100 - page 6

    D. INPUT AND OUTPUT CONNECTIONS CAUTION: When making connections to this component or any other, make sure the power amplifier is OFF and the preamplifier is in the MUTE or STANDBY mode. 1. Connect the speaker cables .to. the output terminals of the amplifier. Tile KS~T-100 utilizes two sets of parallel 5-w~y binding posts tor the left and right ch ...

  • Krell Industries KST100 - page 7

    Thepin assignment for the XLR is: pin _1-= shield (ground) . p!n 2 = non-inverting ~nput (hot) p~n 3 - inverting input NOTE: The RCA center conductor for each channel is wiredjn, parallel with pin 2, the non-inv.erted input. Only one ot tlaese inputs should be connectecl to a preamplifier. 3. Insert the AC power cord into the receptacle located on ...

  • Krell Industries KST100 - page 8

    Eo AMPLIFIER OPERATION 1. Push the black breaker type switc.h on the front of the amplifier to turn it on. The LED in the switch will illumi- nate. When turning on the system, the a _m, plifier should always be last. Upon turn-on, the amplifier s outputs are not connectedto the speakers. After the protection circuits have determined that the unit h ...

  • Krell Industries KST100 - page 9

    E PROTECTION CIRCUITRY There are no fuses in the KST-100. The amplifier is protected by a series of non-intrusive, opto-c_o, upled circuits that constantly evaluate the amplifier s operation. Appropriate protective action exists for DC conditions, short circuit, oscillation, AC power anomalies, high ground resistance and out-of:phase ground. Collec ...

  • Krell Industries KST100 - page 10

    G. MONAURAL CONVERSION AND OPERATION The KST-100 can be easily cgnverted into a 400 watt monaural amplifier. To switcla the amplifier to mono follow these instructions. 1. Remove the topcover from the amplifier via 8 topcover screws. 2. Find the toggle switch located at the rear of the ampli- fier mounted on the circuitboard.. Mo.ve the toggle swit ...

  • Krell Industries KST100 - page 11

    H. REAR PANEL DESCRIPTIONS INPUTS: Balanced via 3 pin XLR connector Single ended via RCA connector XLR PIN CONFIGURATION p!n 1 Shield (ground) p!n 2 Non-inverting or 0 degrees (hot) p~n 3 Inverting or 1-80 degrees OUTPUT: Two pairs of five-way binding posts in parallel, per channel OTHER: Standard AC receptacle 20 amp circuit breaker type power swi ...

  • Krell Industries KST100 - page 12

    I. OUESTIONS AND ANSWERS Q. Should I leave the KST-100 ON at all times? A. Althou.gh you could leave the KST-100 ON at all times without fear of damage to the amplifier, we recom- mend 30 minutes of warm-up_ before critical listening and switching the amplifier off when not in use. ~ . When I push the power switch on the front of the ST-100, the am ...

  • Krell Industries KST100 - page 13

    Q. After the amplifier is playing for about one hour it becomes very hot. Is this normal? A. Yes. Due to the design of the KST-100 it will become quite warm when driven hard. If the amplifier should have a severe temperature inbalance between the left and fight channel, unplug the unit and call your authorized dealer or Krell. Q. I tried a ne.w. pr ...

  • Krell Industries KST100 - page 14

    ¯ I. SPECIFICATIONS KST-100 GAIN 26dB, SIGNAL-TO-NOISE 102dB unweighted THD 1K at 8 ohms less than. 1% 20K at 8 ohms less than .3% INPUT IMPEDANCE 47,000 ohms(47K) INPUT SENSITIVITY 1.5 volts for 100 watts out OUTPUT IMPEDANCE ¯ 1 ohms OUTPUT VOLTAGE 80 volts peak to peak 8 ohms OUTPUT POWER All readings are continuous output power, per channel o ...

  • Krell Industries KST100 - page 15

    K. WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the KST-100. The KST-100 has a limited warranty of .five years parts and labor. Return freight is includedin the warranty.. The warranty, pe~od, begins on ~the date of purchase and is activated witla the return ot the enclosed Warranty Card and a copy of the Sales receip ...

  • Krell Industries KST100 - page 16

    45 CONNAIR RD ORANGE, CT 06477 SALES 203-799-9954 FAX 203-799-9796 ...

Manufacturer Krell Industries Category Stereo Amplifier

Documents that we receive from a manufacturer of a Krell Industries KST100 can be divided into several groups. They are, among others:
- Krell Industries technical drawings
- KST100 manuals
- Krell Industries product data sheets
- information booklets
- or energy labels Krell Industries KST100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Krell Industries KST100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Krell Industries KST100, service manual, brief instructions and user manuals Krell Industries KST100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Krell Industries KST100.

Similar manuals

A complete manual for the device Krell Industries KST100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Krell Industries KST100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Krell Industries KST100.

A complete Krell Industries manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Krell Industries KST100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Krell Industries KST100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Krell Industries KST100, that we can find in the current document
3. Tips how to use the basic functions of the device Krell Industries KST100 - which should help us in our first steps of using Krell Industries KST100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Krell Industries KST100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Krell Industries KST100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Krell Industries KST100?

Use the form below

If you did not solve your problem by using a manual Krell Industries KST100, ask a question using the form below. If a user had a similar problem with Krell Industries KST100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)