English dropdown-ico

Manual Troy-Bilt 634K--ProLine

32 pages 4.93 mb
Download

Go to site of 32

Summary
  • Troy-Bilt 634K--ProLine - page 1

    Rear-tine Tiller Models 630C—T uffy ® 634A—Super Bronco TM 634K—ProLine Model 634A Shown Oper ator’ s Man ual PRINTED IN U.S. A. 770-10594F 10/6/04 FORM NO. IMPOR T ANT : Read saf ety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal co mbustion engine and should not be used on or ...

  • Troy-Bilt 634K--ProLine - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new lawn tractor. It will help you assemble , prepare and maintain the unit for best performance. Please r ead and understand wha t it says. Before you start as sembling your new equipment , plea se locate th e model plate on the equipment a nd copy the ...

  • Troy-Bilt 634K--ProLine - page 3

    3 Training 1. Carefully read this Own- er’ s Manual, the separate Engine Owner’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its en- gine. Know how to stop the unit and disen- gage the controls quickly . 2. Never allow children to operate the tiller . Never all ...

  • Troy-Bilt 634K--ProLine - page 4

    4 4 . Exercise caution to avoid slipping or fall- ing. 5 . If the unit should start to vibrate abnor- mally , stop the engine, disconnect the spark plug wire and prevent it from touch- ing the spark plug, and check immediately for the cause. Vibration is generally a warning of trouble. 6 . Stop the engine, disconnect the spark plug wire and prevent ...

  • Troy-Bilt 634K--ProLine - page 5

    5 Decals For your safety and the safety of others, vari- ous safety and operational decals are located on your unit (see Figure 1-2). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing. Refer to the Parts List pages in this Manual for decal locations ...

  • Troy-Bilt 634K--ProLine - page 6

    6 WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in it ...

  • Troy-Bilt 634K--ProLine - page 7

    7 drive pin (M) through the wheel shaft only (not through the wheel hub). Secure the wheel drive pin with the hairpin cotter (L), pushing the hairpin cotter in as far as it will go. The wheel should now spin freely (freewheel) on the wh eel shaft. Repeat with the other wheel. 4. Use the handlebar to roll the tiller to a flat area. IMPORT ANT: Befor ...

  • Troy-Bilt 634K--ProLine - page 8

    8 4. Check for correct tens ion on the for ward drive belt by taking two measurements of the cable spring, as follows: a. With the Forward Clutch Bail (Y , Fig. 2- 6) in an open (released) position, measure the length of the cable spring (W) from the outermost coil to the outermost coil. b. Squeeze the Forward Clutch Bail against the handlebar (see ...

  • Troy-Bilt 634K--ProLine - page 9

    9 STEP 6: CHECK TRANSMISSION OIL LEVEL The transmission was filled with gear oil at the factory . However , you should check the gear oil level at this time to make certain it is correct. IMPORT ANT : Do not operate the tiller if the gear oil level is low . Doing so will result in severe damage to the transmission com- ponents. 1. With the tiller o ...

  • Troy-Bilt 634K--ProLine - page 10

    10 WARNING: Bef ore operating your machine, carefully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. INTRODUCTION This Section describes the location and function of ...

  • Troy-Bilt 634K--ProLine - page 11

    11 WARNING: Before starting engine, be sure that both wheels are in WHEEL DRIVE position. See Wheels Drive Pins for instructions. Engaging the Forward Clutch Bail or Reverse Clutch Control (if equipped) when the wheels are not in WHEEL DRIVE could allow the tines to rapidly propel the tiller forward or backward. Failure to comply could cause loss o ...

  • Troy-Bilt 634K--ProLine - page 12

    12 WARNING: Bef ore operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injur y . INTRODUCTION Read this Ope ...

  • Troy-Bilt 634K--ProLine - page 13

    13 Stopping the Engine an d Tiller 1. T o stop the wheels and tines, release the Forward Clutch Bail (all models) or the Re- verse Clutch Control (Model 634A) — whichever control is in use. 2. T o stop the engin e, put the ignition switch and/or the throttle control lever in the “OFF” or “STOP” position. OPER ATING THE TILLER The followin ...

  • Troy-Bilt 634K--ProLine - page 14

    14 • When preparing a seedbed, go over the same path twice in the first row , then over- lap one-half the tiller width on the rest of the pas ses (see Fig. 6). When finished in one direction, make a second pass at a right angle, as shown in Fig. 4-7. Overlap each pass for best results (in ver y hard ground, it may take three or four passes to tho ...

  • Troy-Bilt 634K--ProLine - page 15

    15 Power composting simply means tilling under and bur ying in the soil all manner of organic matter such as crop re sidues, leaves, grass clip pings and cover crops. This material will de- compose during the non-growing season and add important natural nutrients to the soil. The first place to begin is with crop residues such as l eftover vines, s ...

  • Troy-Bilt 634K--ProLine - page 16

    16 The tines have a s elf-clearing action which eliminates most tangling of de bris in the tines. However , occasionally dr y grass, stringy stalks or tough v ines may be- come tangled. Follow these procedures to help av oid tangling and to clean the tines, if necessary . • T o reduce tangling, set the depth re gulator deep enough to get maximum ...

  • Troy-Bilt 634K--ProLine - page 17

    17 WARNING: Bef ore inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage. NOTES 1 ...

  • Troy-Bilt 634K--ProLine - page 18

    18 4. The gear oil level is correct if the gear oil is approximately halfway up the side of the main drive shaft. 5. If the gear oil level is low , add gear oil as described next. If the gear oil level is okay , securely replace the oil fill plug. IMPORT ANT : Do not operate the tiller if the gear oil level is low . Doing so will result in severe d ...

  • Troy-Bilt 634K--ProLine - page 19

    19 CHECKING AND ADJUSTING FORW ARD DRIVE BELT TENSION It is important to maintain correct tension on the forward drive belt . A l oose bel t w ill cause the tines and wheels to sl ow do wn — or stop completely — even though the en- gine is running at full speed. A too tight belt can result in u nintentional tine move- ment when the clutch bail ...

  • Troy-Bilt 634K--ProLine - page 20

    20 FORWARD CLUTCH BAIL ADJUSTMENT If the Forward Clutch Bail does not func- tion properly , first check that the forward drive belt is adjusted properly (see Check- ing and Adjusting Forward Drive Belt T en- sion ). If this fails to correct the problem, contact T roy-Bilt LLC or your authorized dealer for service advice. CHECKING AND ADJUSTING RE- ...

  • Troy-Bilt 634K--ProLine - page 21

    21 3. Clean around the oil dipstick or oil fill tube (whichever applies) to prevent dirt from falling into the crankcase. 4. On engines with an oil fill tube, remove the fill cap and add oil (if required) until it reaches the top of the fill tube. Reinstall the fill cap. 5. On engines with a dipstick, remove it and wipe it clean. Reinsert the dipst ...

  • Troy-Bilt 634K--ProLine - page 22

    22 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTION Engine does not start 1. Spark plug wire disconnected. 1. Reconnect wire. 2. Engine Throttle Control L e ver incorrectly set. 2. Put lever in ST ART position. 3. Fuel tank em pty . 3. Add fuel. 4. Choke control (if so equipped) in inco rrect position. 4. See Engine Owner’ s Manual. 5. Stale gas ...

  • Troy-Bilt 634K--ProLine - page 23

    23 REF NO. P ART NO. DESCRIPTION 1 1185469 Spirol Pin (B) 715-0108 Spirol Pin (A) 2 710-0597 Hex Hd. Screw, 1/4-20 x 1 3 710-0599 Screw, Self -Tapping,1/4-20 x 1/2 4 710-0874 Hex Hd. Screw, 5/16-18 x 1-1/4 5 710-3008* Hex Hd. Screw, 5/16-18 x 3/4 6 712-0324 Lock Nut, 1/4-20 (B) 712-04064 Flange Lock Nut, 1/4-20 (A) 7 712-0429 † Lock Nut, 5/16-18 ...

  • Troy-Bilt 634K--ProLine - page 24

    24 MODELS 630C, 634A & 634K 5 10 2 5 15 1 12 16 21 3 13 20 4 17 11 22 7 25 8 6 23 14 1 8 1 8 7 9 ...

  • Troy-Bilt 634K--ProLine - page 25

    25 MODELS 630C, 634A & 634K REF NO. P ART NO. DESCRIPTION 1 1916719 Cable Assembly, Reverse Clutch (B) 2 1916755 Upper Handlebar 3 747-04210 Bail, Forward Clutch 4 1918745 Cable Assembly, Forward Clutch 5 710-0599 Screw, Self-T apping,1/4-20 x 1/2 6 710-3008 Screw, Hex, 5/16-18 x 3/4 7 712-3009 Hex Lock Nut, 5/16-18 8 786-04188 Handlebar Suppor ...

  • Troy-Bilt 634K--ProLine - page 26

    26 MODELS 630C, 634A & 634K * Use as required to obtain between.005” and.0 15” allowable end-p lay . REF NO. P ART NO. DESCRIPTION 1 GW-9517 Snap Ring 2 GW-9400 Drive Shaft Bearing Cup 3 GW-50043 Support Washer, Rear 4 711-04109 Drive Shaft (B) 711-04110 Drive Shaft (A) 5 GW-9401 Drive Shaft Bearing Cone 6 GW-1224-1* Shim, Rear Be aring Cap ...

  • Troy-Bilt 634K--ProLine - page 27

    27 MODELS 630C, 634A & 634K * Use as required to obtain between.005” and.0 30” allowable end-p lay . REF NO. P ART NO. DESCRIPTION 1 GW-9512 Retainer, Snap Ring, “E” Type 2 1909950 Retainer, Snap Ring 3 GW-1166-1* Shim, 0.062" thick GW-1166-2* Shim, 0.030" thick GW-1166-3* Shim, 0.015" thick GW-1166-4* Shim, 0.010" t ...

  • Troy-Bilt 634K--ProLine - page 28

    28 MODELS 630C, 634A & 634K REF NO. P ART NO. DESCRIPTION 1 GW-9727 Plug, T ransmission Oil Fill 2 710-04049 Hex Hd. Flange Sc rew, 5/16-18 x 5/8,Gr. 5 3 736-0119 Lock Washer, 5/16 4 1918377 Rear Cover, Transmission 5 1916641 Front Cover, Transmission 6 GW-50032 Gasket, Housing Cover 7 721-04030 Oil Seal, Drive Shaft 8 721-04031 Oil Seal, Wheel ...

  • Troy-Bilt 634K--ProLine - page 29

    29 MODELS 630C, 634A & 634K FRONT REF NO. P ART NO. DESCRIPTION 1 710-0514 Hex Hd. Screw , 3/8-16 x 1, Grade 5 2 GW-50049-02 Single Bolo Tine - Left Hand (A) (B) 3 712-3000 Hex Lock Nut, 3/8-16 4 710-0347 Hex Hd. Screw, 3/8-16 x 1-3/4 5 GW-50049-01 Single Bolo Tine - Right Hand (A) (B) 6 1916747 Tine Holder (B) 1915075 Tine Holder (A) 7 1917487 ...

  • Troy-Bilt 634K--ProLine - page 30

    30 MODELS 630C, 634A & 634K 9 24 2 8 20 30 25 27 1 1 11 5 17 19 (B) 2 8 (B) 1 (B) 12 10 14 16 3 8 (B) 31 44 3 32 2 7 8 37 19 39 33 4 3 8 34 FORWARD CLUTCH CABLE 35 42 2 8 24 22 22 24 6 13 21 2 8 (B) 16 2 8 (A) 1 8 36 23 41 REVERSE CLUTCH CABLE 15 2 8 29(A) 26 29(B) 45 (A) 43 (A) 40 (A) ...

  • Troy-Bilt 634K--ProLine - page 31

    31 MODELS 630C, 634A & 634K REF NO. P ART NO. DESCRIPTION 1 736-0159 Flat Washer, 5/16 (B) 2 714-0139 Key, 3/16" x 2" 1108841 Key, 3/16" x 1.5” (C) 3 1916531 Pulley, Engine Drive 619-04016 Pulley, Engine Drive (C) 4 1916532 Transmission Pulley (B) 656-04023 Transmission Pulley (A) 5 1916535 Pulley, Reverse Idler (B) 6 1916652 G ...

  • Troy-Bilt 634K--ProLine - page 32

    TR O Y -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt brand ed rear tin e walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of p urchase and is warranted by Troy-Bilt LLC fo r the life of the tiller, to the origin al purchaser only. WHAT IS COVERED Troy-Bilt LLC will, at its option, ...

Manufacturer Troy-Bilt Category Tiller

Documents that we receive from a manufacturer of a Troy-Bilt 634K--ProLine can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- 634K--ProLine manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt 634K--ProLine
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt 634K--ProLine.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt 634K--ProLine, service manual, brief instructions and user manuals Troy-Bilt 634K--ProLine. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt 634K--ProLine.

Similar manuals

A complete manual for the device Troy-Bilt 634K--ProLine, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt 634K--ProLine by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt 634K--ProLine.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt 634K--ProLine - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt 634K--ProLine, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt 634K--ProLine, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt 634K--ProLine - which should help us in our first steps of using Troy-Bilt 634K--ProLine
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt 634K--ProLine
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt 634K--ProLine in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt 634K--ProLine?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt 634K--ProLine, ask a question using the form below. If a user had a similar problem with Troy-Bilt 634K--ProLine it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)