English dropdown-ico

Manual Graco 255963

32 pages 3.43 mb
Download

Go to site of 32

Summary
  • Graco 255963 - page 1

    Instr uctions - P ar ts Doub le W all Hopper For use with XM ™ plural-component spray er s and immer sion heaters. For prof essional use only . 255963, Double W all Hopper 20 Gallon (75 liter ) Spra y Material Fluid Capacity 12 Gallon (45 liter) Heat ed Material Fluid Capacity See page 12 f or optional accesso ries and approv als. Important Safet ...

  • Graco 255963 - page 2

    Related Manua ls 2 312747L Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Optional Accessorie s . . . . . . . . . . . . . . . . . . . . . . . 3 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 K eep Compone nts A and B Sepa rate . . . . . . . . . 6 Changing M aterial s . . . . . . . . ...

  • Graco 255963 - page 3

    Optional Accessories 312747L 3 Optional Accessories See Accessorie s on page 28 f or par ts lists.  Not appro ved f or use in e xp losiv e atmosphers or hazardous location s Not all accessories and kits are app rov ed f or use in hazardous locations . Ref er to the specific accessory and kit manu als f or approv al de tails. P art Description Ap ...

  • Graco 255963 - page 4

    Warnings 4 312747L Wa r n i n g s The f ollowing w arnings are for t he setup , use, g rounding, maintenance , and repair of this equ ipment. The e xclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk. Ref er back to these wa r nings . Additional, product- specific warnings ma y be f o ...

  • Graco 255963 - page 5

    Warnings 312747L 5 W ARNING W ARNING W ARNING W ARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense v alv e, leaks , or ruptured components can spla sh in the ey es or on skin an d cause serious injury . • F ollow Pressure Relief Procedure in this manual, whe n you stop spra ying and before cleaning, chec king, or ser vicing equipmen ...

  • Graco 255963 - page 6

    Warnings 6 312747L K eep Components A and B Separate Changing Materials • When changing m aterials, flush the equipment mul- tiple times to ensure it is th oroughly clean. • Chec k with your mate rial manuf acturer f or chemical compatibility . • Some materials use catalyst on the A side , b ut some applications ma y use catalyst on the B sid ...

  • Graco 255963 - page 7

    Component Identi fication 312747L 7 Component Identification Double W all Hoppers Mounted on Side of Frame Key: AF r a m e BX t r e m e ® low er (behi nd the fr ame) CN X T ™ air motor (behind the frame) D Double wall hopper E Universal hopper mounting kit F Fluid inlet assembly G Retur n tube H F eed pump J Agitator K Desiccant dr yer L Immersi ...

  • Graco 255963 - page 8

    Overview 8 312747L Overview Double wall hopper s (D) can be mounted on the bac k or side of the frame ( A) to gra vity f eed spr a y material to the Xtreme lo wer (B). F e ed pumps (H) and agita tors (J) can be mounted on to p of the hoppers to pre ssure f eed spra y mater ial directly to the pump. A strainer inside th e hopper (D) pre vents object ...

  • Graco 255963 - page 9

    Installation 312747L 9 Installation Hopper mounting kit 256259 allows the ho ppers (D) to mount on the sid es or back of t he frame (A). 1. Mount hoppers (D) on sides of the frame ( A). See F IG . 3. a. Attach ma in brack et (101) to f rame (A) with screw s (107). b . Repeat f or second hoppe r (D) on opposite side of frame (A) . 2. Mount hoppers ( ...

  • Graco 255963 - page 10

    Installation 10 312747L c. Attach the cor ner brac ket (103) to frame (A) with screw s (108) and washe rs (110). d. Attach lower mo unt brack et (104) to frame (A) with screws (108) and washers (110) . e. Attach main br ack et (101 ) to frame (A) with screws (107). f . Repeat steps b and c fo r second hopper (D). 3. Connect reducing s wivel (211) t ...

  • Graco 255963 - page 11

    Installation 312747L 11 7. Align holes on main br ack et (101) and thr ead inser ts of the hopper (D). Loosely f aste n hopper (D) to brac k et (101) with f our scre ws (107) and washers (110). 8. Conne ct s wivel fitting (202) to nipple (201 ). 9. Tighten union (208) and ensure fluid outlet assem- bly is aligned. See F IG . 7 on page 10. 10. Tight ...

  • Graco 255963 - page 12

    Installation 12 312747L Optional Accessories See Accessorie s page 28 f or a list of all accessories that can be used with doub le wall ho ppers. Immersion Heater Kit 256257 Immersion heater kit 2562 57 can only be used with a water mixture or oil in the outer jac ket ed area of the h op- per . 1. Remov e p lug (28) from side of hopp er (D). 2. App ...

  • Graco 255963 - page 13

    Installation 312747L 13 8. Set thermostat knob (TK) to desired spra y ma terial conditioning te mperature. Align tempe rature setting to set point (SP). NO TE: Set point (SP) is a “V” notc h in the metal brac ket at the top of the t hermostat dial. Maxim um setting is 140 °F (60°C). 9. Install immersion heater cov er (HC) with screws (HS). Se ...

  • Graco 255963 - page 14

    Setup 14 312747L Setup 1. Remov e the large A or B label fr om the label sheet (24) and apply t o front f ace of the appropriate hop - per to help av oid filling the wrong materials and causing cross-contamination. 2. Remov e the small A o r B from the label sheet (24) and apply on lid. Connect Return T ube and Recir culation Hose 1. Install return ...

  • Graco 255963 - page 15

    Setup 312747L 15 Fill Heating Fluid Fill the hopper’ s outer jack e ted area with oil or a 50% water an d 50% eth ylene glycol mixture t o heat yo ur spra y material. The doub le wall hopper de sign pre v ents the spr ay mat erial from losing heat during do wntime and ov ernight. 1. Remov e plug (6) from opposite end of 3/4 npt filling por t. 2. ...

  • Graco 255963 - page 16

    Setup 16 312747L 5. Install plug (6) in opposit e por t and torque to 20-30 ft-lbs (27-41 N•m). NO TE: Occasionall y inspect the inside of the hopper for any lea kage of outer c avity heat ing fluid. Fill Spra y Material Condition materials prior to adding to hoppe rs. Ensure resin materials are thoroughly a gitated, homogenous , and poura ble pr ...

  • Graco 255963 - page 17

    Operation 312747L 17 Operation Star tup 1. Ensure that the outer jac k eted area is filled with water mixture or oil and the ac cessor ies are cor- rectly installed. 2. Follo w Setup procedure in man ual 312359. 3. See manual 312 359 f or testing material and oper a- tion inst ructions bef ore spra ying material. Flush Hopper 1. Drain Spra y Materi ...

  • Graco 255963 - page 18

    Maintenance 18 312747L Maintenance Chec k Heating Fluid Level Gradual f luid e va poration can occur , theref ore , check the le v el of heating fluid monthly . 1. Remove plug (6). 2. Place flexible object in por t so that it protr udes down. Pull out to observe le ve l. 3. Refill heating fluid as nec essar y . See Fill Heating Fluid , page 15, f o ...

  • Graco 255963 - page 19

    Maintenance 312747L 19 Drain Spra y Material 1. Flush and Shutdown XM spra y er . See XM opera- tion manual. 2. T urn off all fluid heaters (S) and allow heating flu id to cool for a minimum of 8 ho urs. 3. Place a clean 1 gallon (4 liter) pail directly bene ath union (208 ) and ball valve (206). 4. Close ball v alv e (206) and open union (208 ) wi ...

  • Graco 255963 - page 20

    Repair 20 312747L Repair Remo ve Immer sion Heater 1. T ur n off powe r to system. See the XM Oper ation manual . 2. Drain Heating Fluid . See page 18. 3. Remov e scre ws (HS) and immersion heat er cov er (HC). 4. Disconnect white , blac k, and gr een wires from power cable (303). 5. Loosen b ushing (302) and pu ll power cable (303) out of bushing. ...

  • Graco 255963 - page 21

    Repair 312747L 21 Remo ve Hopper 1. Check Heating Fluid Level . See page 18. 2. Drain Spray Material . See page 19. 3. Disconnect s wiv el fitting (2 02). See F IG . 29. 4. If a transf e r pump (H) or agitator (J) is mounted to the hopper: a. Relieve pressure . See manual 312 769. b . Disconnect air hoses from agitat or and f eed pump. Disconnect f ...

  • Graco 255963 - page 22

    Troubleshooting 22 312747L T roub leshooting Prob lem Cause Solution Lid does not properly seal on hopper . Material build up . Remov e b uilt up material from gas- ket. Replace as necessar y . Damaged gask et. Material leaking betw een cov er an d hopper . Gask et is not sealed properly . Chec k f or bu ilt up material on gask et. Replace as neces ...

  • Graco 255963 - page 23

    Troubleshooting 312747L 23 ...

  • Graco 255963 - page 24

    Parts 24 312747L Pa r t s 255963, Double W all Hopper 1 Assemble with lips f acing down. T orque to 20-30 ft-lbs. Clean groov e with isoprop yl alcohol before applying gask et adhesiv e to plastic. Cut to length. 1 2 3 6 34 4 26 19 7 1c 9 8 10 13 39 28 36 37 1a 11 32 5 33 14 35 32 2 2 2 2 2 1b 24 3 3 12 36 2 6 2 ...

  • Graco 255963 - page 25

    Parts 312747L 25 255963, Double W all Hopper  Replacement Dange r and W arning labels, tags , and cards are av ailab le at no cost. † Supplied spacer kit is f o r installat ion of a 5:1 pump on this hopper . See manual 312769 f or inst ructions. Ref. P art Description Qty 1a HOPPER 1 1b CO VER 1 1c LID 1 4 255965 PLA TE, weldment 2 5 15T007 AD ...

  • Graco 255963 - page 26

    Parts 26 312747L 256259, Double W all Hopper Mounting Kit 107 101 Side Mounted Doub le W all Hopper 107 101 103 108 108 104 Back Mounted Double W all Ho pper 109 107 107 109 107 107 110 110 Ref. Part No. Descri ption Qty . 101 256224 BRA CKET , hopper , 20-gallon 1 103 256254 BRA CKET , hopper , wldmt, bottom mount 1 104 256256 BRA CKET , hopper , ...

  • Graco 255963 - page 27

    Parts 312747L 27 256170, Universal Hopper Fluid Outlet Kit * Parts used for 50 :1 pumps only . † P ar ts u sed with 70:1 pumps on ly . 216 210 209 207 205 204 203 202 206 207 208 201 211 215 212 Apply sealant to all non-swiv eling pipe threads. Do not use pipe sealant on swiv el fittings. 1 2 217 Ref. Part No. Descri ption Qty . 201 121435 N IPPL ...

  • Graco 255963 - page 28

    Accessories 28 312747L Accessories 262820, Flexib le Fluid Connection Kit F or gr avity f eed ing from 20 gallon hopper to propor- tioner with Xtreme lo wer . 256257, 240V 1 PH Immers ion Heater Kit F or non-e xplosiv e atmosphere s only . Includes re-settab le o v er temperatur e s witch. 1500 w atts; 140°F (60°C) maxim um tempera ture. 256512, ...

  • Graco 255963 - page 29

    Technical Data 312747L 29 Te c h n i c a l D a t a Dimensions Hopper 20 Gallon Heated Compat ible Hopper 256233 Maximum (con tinuous) temperature rating . . . . . . . . . . . . 140°F (60° C) Maximum pressu re rating (outer cavity) . . . . . . . . . . . . . . 0 psi (0 MP a, 0 bar) Inner T ank Capacity (spray material) . . . . . . . . . . . . . . . ...

  • Graco 255963 - page 30

    Technica l Data 30 312747L Hopper Stand Hopper on Stand 36 in. (914 mm) 14.5 in. (368 mm) 26.5 in. (673 mm) 1.5 in. (38 mm) 17.5 in. (445 mm) 1.5 in. (38 mm) ti19011a 42.3 in. (1074 mm) 75.4 in. (1915 mm) ...

  • Graco 255963 - page 31

    Technical Data 312747L 31 ...

  • Graco 255963 - page 32

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original instructions. T his manual contains English. MM 312747 Graco Headquarters: Minneapolis ...

Manufacturer Graco Category Pet Fence

Documents that we receive from a manufacturer of a Graco 255963 can be divided into several groups. They are, among others:
- Graco technical drawings
- 255963 manuals
- Graco product data sheets
- information booklets
- or energy labels Graco 255963
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco 255963.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco 255963, service manual, brief instructions and user manuals Graco 255963. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco 255963.

Similar manuals

A complete manual for the device Graco 255963, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco 255963 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco 255963.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco 255963 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco 255963, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco 255963, that we can find in the current document
3. Tips how to use the basic functions of the device Graco 255963 - which should help us in our first steps of using Graco 255963
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco 255963
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco 255963 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco 255963?

Use the form below

If you did not solve your problem by using a manual Graco 255963, ask a question using the form below. If a user had a similar problem with Graco 255963 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)